Formulas and tables
Bearing capacity of shallow foundations
Bearing capacity factors Nc, Nq, NγThe three factors of the bearing-capacity equation for every friction angle from 0° to 50°: Terzaghi’s own factors and those of the general equation, with the Nγ of Meyerhof, Hansen and Vesic side by side.Formulas and table →Shape, depth and inclination factorsThe factors that turn the strip-footing solution into a square, rectangular or embedded footing under an inclined load, with their values for a square footing at Df = B.Formulas and table →
Piles and deep foundations
Meyerhof pile point bearing in sandThe unit point resistance of a pile in sand by Meyerhof (1976): the bearing capacity factor Nq* for every friction angle from 20° to 45°, the limiting value ql, and the effective stress at which that limit takes over.Formulas and table →Vesic pile point bearingThe unit point resistance of a pile in sand by Vesic (1977), from the theory of the expansion of cavities: the rigidity index, its reduced form Irr, and the bearing capacity factor Nσ* for every friction angle from 25° to 45°.Formulas and table →Coyle and Castello methodThe capacity of a pile driven in sand from the field load tests of Coyle and Castello (1981): the point factor Nq* and the shaft coefficient K against the embedment ratio L/D and the friction angle, in two full tables.Formulas and table →Pile skin friction in sandThe shaft resistance of a pile in sand, f = Kσ′otanδ′: how K follows the installation, the range of the pile–soil friction angle δ′, why the friction stops growing at L′ = 15D, and K·tanδ′ for every friction angle from 25° to 40°.Formulas and table →α method for piles in clayThe unit skin friction of a pile in clay as a fraction of the undrained shear strength: the adhesion factor α for driven and for bored piles at every strength from 10 to 280 kPa, with a worked example.Formulas and table →λ method for piles in clayThe average skin friction of a pile in clay from the mean effective stress and the mean undrained strength over its length: the coefficient λ for embedded lengths from 0 to 90 m, and how the two means are taken in a layered clay.Formulas and table →β method for piles in clayThe skin friction of a pile in clay from the vertical effective stress and the remoulded friction angle (Burland, 1973), with the overconsolidation correction of Meyerhof (1976): β for φ′R = 15–35° and OCR = 1–8.Formulas and table →Pile end bearing in clayThe point resistance of a pile in undrained clay by three routes: Meyerhof’s fixed qp = 9cu, Vesic’s factor from the rigidity index, and Reese and O’Neill’s rule for a drilled shaft, with tables for cu = 8–500 kPa.Formulas and table →Pile group efficiencyHow much of the sum of its single piles a group of friction piles carries: the Converse–Labarre equation, the Los Angeles and Seiler–Keeney equations, the rules for sand, and η for the usual layouts.Formulas and table →Pile group block failureWhen piles stand close together in a soft clay, the piles and the soil between them can sink as one block. Its capacity, the factor Nc* of its base, and the spacing at which the block governs.Formulas and table →Load on each pile of a groupHow a rigid cap shares a vertical load and two moments among its piles: the formula, the sums Σx² and Σy² of the usual layouts, when a pile goes into tension, and a worked example with the load on every pile.Formulas and table →p–y curves for sand and clayThe non-linear springs of a laterally loaded pile: the API curve of a sand after Reese, Cox and Koop, the soft-clay curve of Matlock, their ultimate resistances, and the curves at one depth, static and cyclic.Formulas and table →Pile uplift capacityHow much a pile can carry when it is pulled rather than pushed: the shaft resistance in tension in sand and in clay, the weight, and the piles of a group in tension checked against the block of soil around them.Formulas and table →p-multipliers of a pile groupWhy the rows of a pile group pushed sideways do not carry the same load: the p-multipliers of the leading, second, third and trailing rows against the spacing, for sand and for clay, and the group solved under a rigid cap.Formulas and table →Pile group settlementWhy a group of piles settles more than one pile, and by how much: the consolidation of the clay below the group by the equivalent footing at two thirds of the pile length, and the elastic settlement of the group from that of one pile.Formulas and table →Elastic settlement of a single pileHow far a pile settles at its working load: the shortening of the pile itself, the settlement its point load causes and the settlement its shaft load causes, with the influence factors and the distribution factor ξ.Formulas and table →Deflection and bending moment of a laterally loaded pileHow far the head of a pile moves under a lateral load, how large the bending moment gets and at what depth: the beam on non-linear springs, the head free or held, and one pile in sand worked from a small load to a large one.Formulas and table →Coefficient of subgrade reaction nh and khThe springs of the elastic solution of a laterally loaded pile: nh for a sand, kh for a clay, the relative stiffness T and R, the coefficients of Matlock and Reese, and how far the elastic answer stays from the p–y one as the load grows.Formulas and table →
Lateral earth pressure
Earth pressure coefficients Ka, Kp, K0The active, passive and at-rest coefficients for every friction angle from 20° to 45°: Rankine’s, Coulomb’s with wall friction, and Jaky’s K0.Formulas and table →Mononobe–Okabe coefficient KAEThe active earth pressure on a wall during an earthquake: the pseudo-static Mononobe–Okabe coefficient for horizontal seismic coefficients from 0 to 0.4.Formulas and table →Earth pressure at rest K0The coefficient of earth pressure at rest for sands, clays and compacted fills, and how overconsolidation raises it: K0 against φ′ and OCR, against the plasticity index, and against the degree of compaction.Formulas and table →Rankine earth pressure with a sloping backfillThe active and passive Rankine coefficients when the ground behind the wall slopes, for every friction angle from 20° to 45°, and the general case of a wall whose back is inclined, after Chu (1991).Formulas and table →Coulomb earth pressure on an inclined wallCoulomb’s active and passive coefficients for a wall whose back is inclined, behind a sloping granular backfill, with friction between wall and soil: the general formulas, tables for the usual wall friction and the limits of the passive wedge.Formulas and table →Log-spiral passive earth pressureThe passive resistance of a granular soil against a rough wall, on the curved failure surface that wall friction produces: Kp for every friction angle from 20° to 45°, compared with Coulomb, Rankine and Lancellotta.Formulas and table →
Retaining walls
Sheet-pile walls
Cantilever sheet pile in sandHow deep a cantilever sheet-pile wall must be driven into sand, and what bending moment it must carry: the net pressure diagram, the equilibrium equations, the margin on the depth, and the depth and moment for every friction angle from 26° to 40°.Formulas and table →Cantilever sheet pile in clayHow deep a cantilever sheet-pile wall must be driven into a saturated clay in the short term, when the clay is undrained: the constant net pressure 4cu − (γL1 + γ′L2), the quadratic for the depth, the maximum moment, and the depth for every strength ratio cu/γL.Formulas and table →Anchored sheet pile, free earth supportHow a sheet-pile wall held by one row of anchors is designed by the free earth support method: the moment equation about the anchor, the anchor force, the maximum moment, the free length and bond of the anchors, and the depth for every friction angle from 28° to 38°.Formulas and table →
Braced excavations
Apparent earth pressure for braced cutsThe pressure envelopes from which the struts of a braced excavation are designed: sand, soft to medium clay and stiff clay, the stability number that decides between the clays, and the strut loads by the hinge method, with every ordinate tabulated.Formulas and table →Bottom heave of a braced cut in clayWhether the base of a deep excavation in soft clay will heave: the factor of safety against bottom heave, the effect of a firm stratum below the base and of the length of the cut, and FS for every stability number from 3 to 9.Formulas and table →
Surcharge loads on walls
Settlement and consolidation
Time factor Tv and degree of consolidation UHow long a clay layer takes to consolidate: Terzaghi’s one-dimensional solution, its two well-known approximations and the time factor for every 5 % of consolidation.Formulas and table →Steinbrenner influence factors F1, F2, IsThe settlement of the corner of a uniformly loaded rectangle on an elastic layer over a rigid base: Steinbrenner’s closed-form factors for every shape and thickness, how they depend on Poisson’s ratio, and how four corners give the centre of a footing.Formulas and table →Elastic settlement of a footingThe settlement a shallow foundation undergoes as it is loaded: the elastic formula with Steinbrenner’s factors, the modulus of clay and of sand, the net pressure, layered ground and the depth down to which the soil is counted.Formulas and table →Consolidation settlement of clayHow much a clay layer compresses as the water drains from it: the e–log σ′ formulas for normally consolidated and overconsolidated clay, the settlement of one metre of clay for every load and OCR, and the stress path of an excavation that is loaded again.Formulas and table →Total settlement of a foundationA foundation on clay and sand settles twice: at once, as the ground deforms under the load, and over months or years, as the clay drains. How the two parts are found on one profile, how they add up with time, and which one governs.Formulas and table →
Stress distribution in soil
Boussinesq point loadThe vertical stress a point load causes at any depth in an elastic half-space, the influence factor for every r/z from 0 to 3, and how to use it.Formulas and table →Stress below a rectangular footingThe vertical stress below a corner of a uniformly loaded rectangle, its influence factor for m = B/z and n = L/z, and how the corners add up to give the stress anywhere.Formulas and table →Stress below a circular loadThe vertical stress increase below a uniformly loaded flexible circle, such as a tank or a circular raft: the closed form under the centre, the integral for any other point, and Δσz/q for every depth and offset.Formulas and table →Stress below a strip loadThe stresses a uniform load on a long strip of width B causes in an elastic half-space: the closed form, the angle form with α and δ, Δσz/q for every depth and offset, and the stresses below the centre and the edge.Formulas and table →Stress below an embankmentThe vertical stress a road or railway embankment, a levee or a long stockpile causes in the ground: Osterberg’s influence factor for a half embankment, its table against a/z and b/z, and how the halves add up below the crest, the slopes and beyond the toe.Formulas and table →Stress below a line loadThe stresses a load per unit length along a straight line causes in an elastic half-space: Δσz, Δσx and τxz of a vertical line load, the vertical stress below a horizontal one, a table against x/z, and when a narrow footing may be treated as a line.Formulas and table →Westergaard stress distributionThe vertical stress in a soil whose thin, stiff horizontal layers prevent lateral strain: Westergaard’s point load, circle and rectangle, their influence factors side by side with Boussinesq’s, and when each applies.Formulas and table →