1The free earth support methodThe wall turns about the anchor.
When the retained height is too great for a cantilever, the wall is tied back near its top by anchors or tie rods. The anchor becomes a support, the wall bends as a beam between the anchor and the soil in front of its embedded part, and it needs far less embedment and a far smaller section.
In the free earth support method the embedment is taken just deep enough for the passive resistance in front of the wall to balance it: the toe is free to move and rotate, and the wall turns about the anchor as a rigid body. Rankine’s coefficients are used on both faces (see earth pressure coefficients). With one row of anchors the problem has two unknowns, the depth D and the anchor force F per metre of wall, and two equations:
the moment of the net pressure about the anchor at depth za must vanish, and the anchor takes the rest of the horizontal force. Deeper walls develop a fixity at the toe, and Blum (1931) treated that case — the fixed earth support method — with an equivalent beam; the free earth support method is the simpler of the two, and the one used here.
2The equations for one sandA cubic in L4.
The net pressure diagram is that of the cantilever wall above the toe (see cantilever sheet pile in sand): the active pressure σ′1 = γL1Ka at the water table and σ′2 = (γL1 + γ′L2)Ka at the dredge line, the zero point E at L3 = σ′2/γ′(Kp − Ka) below it, P the area above E and z̄ its height above E. Below E the net passive pressure grows linearly over L4, and there is no reversal at the toe. Taking moments about the anchor gives a cubic in L4:
and the horizontal forces give the anchor force per metre of wall and the theoretical depth:
GeoTerva does not rely on the closed form: it scans the whole range of depths, closes every root of the moment equation by Brent’s method and keeps the smallest one with the anchor in tension. For one sand the two agree, and on layered soil, with water at different levels or with surcharges, the scan still applies where the cubic does not.
3Design depth and maximum momentThe margin, and zero shear between the anchor and the dredge line.
At Dtheory the passive resistance is fully mobilised. As for the cantilever, the margin goes either on the depth, Ddesign = f Dtheory with f = 1.2–1.3 (the GeoTerva module proposes f = 1.3), or on the passive pressure, divided by FSp = 1.5–2 before solving, which increases D and F together.
The shear force is F just below the anchor and falls as the active pressure accumulates; the largest moment is where it reaches zero, usually between the anchor and the dredge line:
Rowe (1952) showed that a flexible wall in sand carries less moment than the free earth support diagram gives, the pressures redistributing as the wall bends; the GeoTerva module reports the moment of the limit-equilibrium diagram, without that reduction.
4The anchorsForce, free length and bond.
Each anchor of a row at horizontal spacing s and inclination α below the horizontal carries
The vertical component Tv acts downwards on the wall. The bond zone must begin behind the critical surface, which is taken from the foot of the excavated face (the wall at the dredge line) rising to the retained side at θ = 45° + φ′/2. Along the tendon it is crossed at sc, and the free length must reach beyond it by at least max(1.5 m, L/5), and be no shorter than 4.5 m for strands or 3 m for bars (FHWA GEC-4, Sabatini et al. 1999):
The ground bond is estimated from the diameter Db and length Lb of the grout body and the ultimate bond stress τult, and compared with the anchor force (the GeoTerva module also compares it with the lock-off load):
5Table of the depth, the anchor force and the momentDry sand, two anchor levels.
| φ′ (°) | Dtheory/L, za = 0.1L | F/(γL²) | Mmax/(γL³) | Dtheory/L, za = 0.25L | F/(γL²) | Mmax/(γL³) | Cantilever Dtheory/L |
|---|---|---|---|---|---|---|---|
| 28 | 0.442 | 0.1047 | 0.0427 | 0.423 | 0.1180 | 0.0341 | 1.117 |
| 30 | 0.392 | 0.0927 | 0.0368 | 0.374 | 0.1049 | 0.0293 | 1.004 |
| 32 | 0.348 | 0.0822 | 0.0319 | 0.332 | 0.0935 | 0.0253 | 0.906 |
| 34 | 0.309 | 0.0730 | 0.0277 | 0.295 | 0.0834 | 0.0219 | 0.819 |
| 36 | 0.276 | 0.0650 | 0.0241 | 0.262 | 0.0745 | 0.0190 | 0.741 |
| 38 | 0.246 | 0.0578 | 0.0211 | 0.233 | 0.0666 | 0.0166 | 0.672 |
L is the retained height and za the depth of the anchor below the top; the same γ on both faces, no water, no surcharge. F is the anchor force per metre of wall. Values computed by GeoTerva with the functions of its anchored sheet-pile module; the last column is the cantilever wall without an anchor.
At φ′ = 30° with the anchor at 0.1L, Dtheory = 0.392 L against 1.004 L for the cantilever, and Mmax = 0.0368 γL³ against 0.1250 γL³. Lowering the anchor shortens the span below it and reduces the moment, but raises the force the anchor must carry.
6Worked exampleA quay wall, L = 8.5 m, one row of anchors.
A sheet-pile wall retains L = 8.5 m of sand (φ′ = 32°, γ = 18 kN/m³, γsat = 20.5 kN/m³); the water stands 3.0 m below the top on both faces. One row of anchors is placed za = 1.6 m below the top. Ka = 0.3073, Kp = 3.2546, γ′ = 10.69 kN/m³ and γ′(Kp − Ka) = 31.507 kN/m³.
- Net pressure: σ′1 = 16.59 kPa at the water table, σ′2 = 34.66 kPa at the dredge line, L3 = 1.100 m; above E, P = 184.88 kN/m acting z̄ = 3.787 m above E.
- Cubic: L4³ + 1.5 × 8.000 L4² − 3 × 184.88 × 4.213 / 31.507 = 0 gives L4 = 2.279 m and Dtheory = 3.38 m; the scan of the module finds the same root.
- Anchor force: F = 184.88 − ½ × 31.507 × 2.279² = 103.1 kN/m.
- Design depth: Ddesign = 1.3 × 3.38 = 4.39 m, a sheet pile 12.89 m long. Dividing the passive pressure by 1.5 instead gives D = 4.61 m and F = 113.9 kN/m.
- Maximum moment: the shear is zero at z = 6.50 m below the top, where Mmax = 267.9 kN·m/m. Without the anchor the same wall would need Dtheory = 9.08 m and carry 1122 kN·m/m.
The anchors are spaced at s = 2.5 m and inclined α = 15°; they are strands with a free length Lf = 7.0 m and a grout body Db = 0.15 m by Lb = 8.0 m in sand with τult = 150 kPa.
- Force per anchor: Th = 103.06 × 2.5 = 257.7 kN, T = 257.7 / cos 15° = 266.7 kN, Tv = 69.0 kN down the wall.
- Free length: θ = 45° + 32°/2 = 61°, sc = (8.5 − 1.6) / (cos 15° tan 61° + sin 15°) = 3.45 m, Lf,req = 3.45 + 1.70 = 5.15 m ≤ Lf = 7.0 m: satisfied.
- Bond: Tult = π × 0.15 × 8.0 × 150 = 565.5 kN, FSbond = 565.5 / 266.7 = 2.12 ≥ 2.0.
The anchored sheet pile module of GeoTerva carries out these steps on a profile of sand and clay layers with up to four rows of anchors (the hinge method below the uppermost), runs the short- and long-term scenarios, verifies the section and estimates the displacement of the wall with the anchors as prestressed springs. A strip or point load behind the wall adds the lateral pressure of surcharge loads.
7QuestionsShort answers.
What is the free earth support method?
A limit-equilibrium design of an anchored sheet-pile wall in which the embedment is just deep enough for the passive resistance to balance the wall turning about the anchor: the toe is free to move, the depth comes from the moments about the anchor and the anchor force from the horizontal forces.
How much embedment does an anchored wall need compared with a cantilever?
Far less. In dry sand with φ′ = 30° and the anchor at a tenth of the retained height, Dtheory is about 0.39 L against 1.00 L for a cantilever, and the maximum moment is 29 % of the cantilever’s.
Where must the anchor bond zone begin?
Behind the critical surface that rises from the foot of the wall at the dredge line at 45° + φ′/2, with a further margin of max(1.5 m, L/5) along the tendon; the free length must also be at least 4.5 m for strands and 3 m for bars.