GeoTerva Open the module

Formulas and tables · Sheet-pile walls

Cantilever sheet pile in sand: embedment depth and maximum moment

How deep a cantilever sheet-pile wall must be driven into sand, and what bending moment it must carry: the net pressure diagram, the equilibrium equations, the margin on the depth, and the depth and moment for every friction angle from 26° to 40°.

  • Free to read
  • φ′ = 26–40°
  • D/L and M/(γL³)
  • Worked example

1How a cantilever wall standsRotation about a point near the toe.

A cantilever sheet-pile wall has no anchor: it holds the retained soil by its embedment alone. Pushed by the soil behind it, the wall rotates about a point a little above its toe. Above that point it moves towards the excavation, so the retained soil is in the active state and the soil in front of the embedded part in the passive state; below it the movement reverses, and so do the pressures — passive behind the toe, active in front of it.

The conventional method of limit equilibrium replaces this distribution by straight lines with Rankine’s coefficients (see earth pressure coefficients):

Ka=tan2(45°−φ′2),Kp=tan2(45°+φ′2)

The wall friction is neglected, which is on the safe side for the passive pressure. The two equations of equilibrium of the wall — no net horizontal force, no net moment — then fix the depth of embedment D below the dredge line, and the shear and moment along the wall follow from the same diagram.

2The net pressure diagramActive above, net passive below the zero point.

Let the water table lie at depth L1 below the top of the wall and the dredge line a further L2 below it, the water standing at the same level on both faces so that the water pressures cancel. With γ the unit weight above the water and γ′ = γsat − γw below it, the active pressure at the water table and at the dredge line is

σ1′=γL1Ka,σ2′=(γL1+γ′L2)Ka

Below the dredge line the passive pressure in front of the wall grows faster than the active pressure behind it, so the net pressure falls with the slope γ′(Kp − Ka) and becomes zero at the point E, a depth L3 below the dredge line:

L3=σ2′γ′(Kp−Ka)

P is the area of the net diagram above E (per metre of wall) and z̄ the height of its centroid above E. Below E the net pressure acts towards the retained side and reaches, at the toe, a depth L4 below E,

σ3′=L4γ′(Kp−Ka)

Behind the toe the passive pressure of the retained soil takes over. Its net ordinate at the toe is

σ4′=σ5′+γ′L4(Kp−Ka),σ5′=(γL1+γ′L2)Kp+γ′L3(Kp−Ka)

and the reversal is drawn as a triangle of height L5 above the toe, on which the net pressure swings from the line E–toe to σ′4.

3The equilibrium equationsL5 from the forces, L4 from the moments.

No net horizontal force on the wall gives the height of the toe block:

L5=σ3′L4−2Pσ3′+σ4′

No net moment about the toe, with L5 substituted, gives a quartic in L4:

L44+A1L43−A2L42−A3L4−A4=0
A1=σ5′γ′(Kp−Ka),A2=8Pγ′(Kp−Ka)
A3=6P[2z¯γ′(Kp−Ka)+σ5′]γ′2(Kp−Ka)2,A4=P(6z¯σ5′+4P)γ′2(Kp−Ka)2

The quartic has one positive root; GeoTerva brackets it and refines it by Newton’s method. The theoretical depth of embedment is

Dtheory=L3+L4

With no water table, L1 = L, L2 = 0 and γ′ is replaced by the moist γ. The GeoTerva module generalises the retained side to several layers, each with its own γ and φ′, and to water at different levels on the two faces; the equations above are the case of one sand.

4The design depthA margin on the depth, or on Kp.

At Dtheory the passive resistance is fully mobilised: the wall is just in equilibrium, with no margin. The margin is put in one of two ways:

  • Increase the depth. The analysis is run with the full Rankine Kp and the depth is increased by 20 to 30 %: Ddesign = f Dtheory, f = 1.2–1.3 (the GeoTerva module proposes f = 1.3). The pressure diagram and the moment are those of the theoretical wall.
  • Reduce Kp. The passive coefficient is divided by a factor of safety FSp = 1.5–2 from the outset, and the depth that comes out is used as it is. L3, L4 and the maximum moment all grow.
Ddesign=fDtheoryorDdesign=Dtheory(KpFSp)

For dry sand the two routes come out close to each other (Table 1, columns f = 1.3 and FSp = 1.5); the second gives the larger moment, because the whole diagram is built with the reduced resistance.

5The maximum bending momentWhere the shear force is zero.

The bending moment is largest where the shear force is zero. Below E the net pressure acts towards the retained side, so the shear falls from P at E to zero at a depth z′ below E:

z′=2Pγ′(Kp−Ka)
Mmax=P(z¯+z′)−[12γ′z′2(Kp−Ka)]z′3

The section of the sheet pile is chosen from Mmax: the GeoTerva module verifies it to EN 1993-1-1 or AISC 360-22. For dry, homogeneous sand every length in the diagram is proportional to the retained height L and the pressures to γL, so D grows in proportion to L and Mmax to γL³: doubling the retained height multiplies the moment by eight.

6Tables of the depth and the momentDry sand, and the effect of the water table.

Table 1. Cantilever wall in dry, homogeneous sand: depths as a fraction of the retained height L, moment as a multiple of γL³
φ′ (°)KaKpL3/LDtheory/LDdesign/L, f = 1.3D/L, Kp/1.5z′/LMmax/(γL³)
260.3902.5610.1801.2461.621.710.4610.1752
280.3612.7700.1501.1171.451.500.4150.1474
300.3333.0000.1251.0041.311.330.3750.1250
320.3073.2550.1040.9061.181.180.3390.1067
340.2833.5370.0870.8191.061.060.3070.0916
360.2603.8520.0720.7410.960.950.2780.0789
380.2384.2040.0600.6720.870.850.2520.0683
400.2174.5990.0500.6100.790.760.2280.0592

The same γ on both faces, no water, no surcharge. Multiply by L (m) for the depths and by γL³ (kN·m per metre of wall) for the moment. Values computed by GeoTerva with the function its sheet-pile module uses.

At φ′ = 30° the theoretical depth is about 1.00 L; at φ′ = 35° it falls to 0.78 L. A water table changes this a great deal, because below it the passive resistance is built on the submerged unit weight:

Table 2. The water table: L = 6 m, φ′ = 32°, γ = 18 kN/m³, γsat = 20 kN/m³
Water table below the topDtheory (m)Ddesign (m), f = 1.3Mmax (kN·m/m)
none (dry)5.437.06414.9
0.0 m (at the top)5.437.06234.9
1.5 m6.278.15354.4
3.0 m6.828.86443.6
4.5 m7.199.35505.1
6.0 m (at the dredge line)7.449.68542.8

The water stands at the same level on both faces; with a water table at or above the dredge line the embedded sand is submerged on both faces. Values computed by GeoTerva.

Even a water table at the dredge line, which leaves the retained soil dry, raises Dtheory from 5.43 m to 7.44 m: the passive resistance of the submerged sand is little more than half that of the dry sand. With the water at the top the whole profile is submerged: the depth is that of the dry wall, and the moment is smaller in the ratio γ′/γ.

7Worked exampleA waterfront wall, L = 5.5 m.

A cantilever wall retains L = 5.5 m of sand above the dredge line; the water stands 2.0 m below the top on both faces, so L1 = 2.0 m and L2 = 3.5 m. The sand, above and below the dredge line, has φ′ = 33°, γ = 17.5 kN/m³ and γsat = 20.0 kN/m³, so γ′ = 10.19 kN/m³.

  • Coefficients: Ka = 0.2948, Kp = 3.3921, γ′(Kp − Ka) = 31.562 kN/m³.
  • Active pressures: σ′1 = 17.5 × 2.0 × 0.2948 = 10.32 kPa; σ′2 = (17.5 × 2.0 + 10.19 × 3.5) × 0.2948 = 20.83 kPa.
  • Zero point: L3 = 20.83 / 31.562 = 0.660 m.
Table 3. The net pressure diagram above E, block by block
BlockShape and depthArea (kN/m)Arm above E (m)Moment about E (kN·m/m)
1triangle, 0.0–2.0 m10.324.82749.80
2rectangle, 2.0–5.5 m36.112.41087.03
3triangle, 2.0–5.5 m18.401.82733.61
4triangle, dredge line to E6.880.4403.03
Σ71.712.419173.47

Depths from the top of the wall. z̄ = Σ(area × arm)/P. Values computed by GeoTerva.

  • Coefficients of the quartic: σ′5 = 260.54 kPa, A1 = 8.255, A2 = 18.175, A3 = 178.48, A4 = 292.87.
  • Root: L4 = 4.977 m, so Dtheory = 0.660 + 4.977 = 5.64 m. The toe block: σ′3 = 157.1 kPa, σ′4 = 417.6 kPa, L5 = 1.111 m.
  • Design depth: Ddesign = 1.3 × 5.64 = 7.33 m, a sheet pile 12.83 m long. Dividing Kp by 1.5 instead would give D = 7.36 m.
  • Maximum moment: z′ = √(2 × 71.71 / 31.562) = 2.132 m below E, that is 2.79 m below the dredge line; Mmax = 71.71 × (2.419 + 2.132) − ½ × 31.562 × 2.132² × 2.132/3 = 275.4 kN·m/m (341.2 kN·m/m with Kp/1.5).

The net diagram closes: the shear and the moment at the toe come back to zero. The sheet pile in sand module of GeoTerva carries out these steps for layered retained soil, water at different levels, surcharges and the seismic situation, verifies the section and estimates the displacement of the wall. The same wall with an anchor near its top needs far less embedment (see anchored sheet pile, free earth support).

8QuestionsShort answers.

How deep must a cantilever sheet pile be driven into sand?

To the theoretical depth from the equilibrium of the net pressure diagram, increased by 20 to 30 %. For dry sand with φ′ = 30° the theoretical depth is about 1.00 times the retained height, so the design depth is about 1.31 L; a water table in front of the wall makes it deeper.

Why is the theoretical depth not used as it is?

At Dtheory the passive resistance in front of the wall is fully mobilised, so the wall has no margin against rotation. The margin is added either by driving the pile 20–30 % deeper or by dividing Kp by a factor of safety of 1.5–2 before solving.

Where does the maximum bending moment occur?

Below the dredge line, where the shear force is zero: at z′ = √(2P/γ′(Kp − Ka)) below the zero point E of the net pressure. When the margin is put on the depth, increasing D does not change Mmax.

The theory behind it