1Below the centreBoussinesq’s point load summed over rings.
A flexible circle of radius R carries a uniform pressure q on the surface of a homogeneous, isotropic, linearly elastic half-space. Divide it into rings of radius ρ and width dρ: each ring carries q·2πρ dρ, and every point of the ring is at the same distance from the axis, so Boussinesq’s (1883) point-load solution (see Boussinesq point load) gives the vertical stress at depth z on the axis directly:
ψ is the half-angle under which the circle is seen from the point (tan ψ = R/z). The stress depends only on z/R: at z = R it is 0.646q, half of q is reached at z = 1.30R, and the stress falls to 0.1q at z = 3.71R. Like every Boussinesq stress, Δσz does not depend on the elastic constants of the soil, and it is an increase: the overburden pressure is added separately.
2At any other pointAhlvin and Ulery (1962), and the integral about the point.
Off the axis there is no closed form. Ahlvin and Ulery (1962) evaluated the integrals and tabulated the stress as the sum of two functions of z/R and r/R, Δσz = q(A′ + B′). The GeoTerva module does not interpolate in such tables: it integrates Boussinesq’s solution over the circle in polar co-ordinates ρ, φ centred on the vertical through the point. The radial integral along each ray is closed, and the remaining integral over the direction φ has a smooth integrand:
r is the horizontal distance of the point from the centre of the circle. A ray crosses the loaded area between ρ1 and ρ2; for a point under the circle ρ1 is taken as zero, and for a point beside it only the directions that meet the circle contribute. On the axis (r = 0) the integral returns the closed form above exactly. Several circles, each with its own pressure and radius, are added point by point: the soil is elastic, so their stresses superpose.
3Tables of Δσz/qz/R down, r/R across; the depth of the pressure bulb.
| z/R \ r/R | 0 | 0.25 | 0.5 | 0.75 | 1 | 1.25 | 1.5 | 2 | 3 |
|---|---|---|---|---|---|---|---|---|---|
| 0.25 | 0.986 | 0.982 | 0.966 | 0.884 | 0.460 | 0.074 | 0.014 | 0.002 | 0.000 |
| 0.5 | 0.911 | 0.896 | 0.840 | 0.692 | 0.417 | 0.169 | 0.060 | 0.010 | 0.001 |
| 0.75 | 0.784 | 0.763 | 0.692 | 0.558 | 0.374 | 0.207 | 0.102 | 0.026 | 0.003 |
| 1 | 0.646 | 0.626 | 0.562 | 0.459 | 0.332 | 0.214 | 0.127 | 0.042 | 0.006 |
| 1.25 | 0.524 | 0.507 | 0.458 | 0.382 | 0.292 | 0.206 | 0.137 | 0.055 | 0.010 |
| 1.5 | 0.424 | 0.411 | 0.375 | 0.320 | 0.256 | 0.193 | 0.138 | 0.065 | 0.015 |
| 2 | 0.284 | 0.278 | 0.259 | 0.230 | 0.196 | 0.160 | 0.126 | 0.073 | 0.023 |
| 2.5 | 0.200 | 0.196 | 0.186 | 0.170 | 0.151 | 0.130 | 0.109 | 0.072 | 0.028 |
| 3 | 0.146 | 0.144 | 0.138 | 0.129 | 0.118 | 0.105 | 0.092 | 0.067 | 0.031 |
| 4 | 0.087 | 0.086 | 0.084 | 0.081 | 0.076 | 0.071 | 0.065 | 0.053 | 0.031 |
| 5 | 0.057 | 0.057 | 0.056 | 0.054 | 0.052 | 0.050 | 0.047 | 0.040 | 0.028 |
| 6 | 0.040 | 0.040 | 0.040 | 0.039 | 0.038 | 0.036 | 0.035 | 0.031 | 0.024 |
| 8 | 0.023 | 0.023 | 0.023 | 0.023 | 0.022 | 0.022 | 0.021 | 0.020 | 0.017 |
| 10 | 0.015 | 0.015 | 0.015 | 0.015 | 0.014 | 0.014 | 0.014 | 0.013 | 0.012 |
r/R = 0: the closed form; r/R > 0: the integral about the point (2880 directions). Below the edge (r/R = 1) the value tends to 0.5 at the surface. Values computed by GeoTerva with the functions its circular load module uses.
Outside the loaded area (r/R > 1) the stress is small near the surface, rises to a maximum and then decreases: the load spreads sideways as it goes down, and the farther the point lies from the circle, the deeper its maximum.
| Δσz/q | z/R, circle | z/R, strip of width B = 2R |
|---|---|---|
| 0.90 | 0.52 | 0.74 |
| 0.80 | 0.72 | 1.06 |
| 0.70 | 0.90 | 1.39 |
| 0.60 | 1.09 | 1.77 |
| 0.50 | 1.30 | 2.26 |
| 0.40 | 1.57 | 2.96 |
| 0.30 | 1.93 | 4.08 |
| 0.20 | 2.50 | 6.26 |
| 0.10 | 3.71 | 12.68 |
| 0.05 | 5.36 | 25.44 |
The strip column is the centre line of a strip as wide as the diameter of the circle (see stress below a strip load). Values computed by GeoTerva by bisection on its closed forms.
4Worked exampleA tank on a clay layer, and its neighbour.
A steel tank of diameter 15 m (R = 7.5 m) stands on a flexible base and applies q = 120 kPa when full. A soft clay layer lies between 4 m and 10 m below the ground; its middle is at z = 7 m.
- Below the centre: R/z = 7.5/7 = 1.0714, (R/z)² = 1.1480, 1/[1 + (R/z)²] = 0.4656, raised to the power 3/2: 0.3177. Δσz = 120 × (1 − 0.3177) = 81.9 kPa.
- Below the edge (r = 7.5 m, r/R = 1): the integral gives Δσz = 41.2 kPa, 50 % of the centre value: the base of a flexible tank settles into a dish.
- Beside the tank (r = 12 m, 4.5 m outside the shell): Δσz = 11.5 kPa.
A second, identical tank is built with its centre 18 m away (a clear gap of 3 m). At the same depth it adds 1.9 kPa below the centre of the first tank (r = 18 m) and 18.4 kPa below its nearer edge (r = 10.5 m): the near edge of each tank now carries 59.6 kPa, the far edge 41.5 kPa, and the bases tilt towards each other.
| z (m) | z/R | r = 0 | r = R (edge) | r = 12 m | edge/centre |
|---|---|---|---|---|---|
| 2 | 0.27 | 117.9 | 54.8 | 1.2 | 0.46 |
| 4 | 0.53 | 107.5 | 49.4 | 5.5 | 0.46 |
| 7 | 0.93 | 81.9 | 41.2 | 11.5 | 0.50 |
| 10 | 1.33 | 58.6 | 33.6 | 14.1 | 0.57 |
| 15 | 2.00 | 34.1 | 23.5 | 13.7 | 0.69 |
| 20 | 2.67 | 21.5 | 16.7 | 11.5 | 0.78 |
q = 120 kPa, R = 7.5 m. Values computed by GeoTerva with the functions its circular load module uses.
5QuestionsShort answers.
What is the stress below the edge of a circular load?
At the surface it is half the applied pressure, q/2. With depth it falls more slowly than below the centre, so the two come closer: at z = R it is 0.332q against 0.646q below the centre (Table 1).
Does the formula hold for a rigid circular footing?
It is written for a flexible load, a uniform pressure on the ground. Below a rigid footing the contact pressure is not uniform (it is higher towards the edge on an elastic soil), but the difference fades with depth; below about one radius the stresses of the two are close, and the flexible solution is the usual basis of the stress increase in a settlement estimate.
How deep does a circular load affect the ground?
Below the centre Δσz falls to 0.2q at about z = 2.5R and to 0.1q at about 3.7R (Table 2). Below a strip as wide as the diameter the 0.1q depth is 12.7R: a long load stresses the ground much deeper than a circle or a square of the same width.