GeoTerva Open the module

Formulas and tables · Stress distribution

Stress below a strip load: Δσz, Δσx and τxz

The stresses a uniform load on a long strip of width B causes in an elastic half-space: the closed form, the angle form with α and δ, Δσz/q for every depth and offset, and the stresses below the centre and the edge.

  • Free to read
  • x/B = 0–3
  • z/B = 0.1–6
  • Worked example

1The strip loadThe line load integrated over a width.

A long footing, a road, a wall base: many loads are long in one direction and of finite width B in the other. A flexible strip of infinite length carrying a uniform pressure q loads every cross section in the same way, so the stresses are those of plane strain and depend only on the horizontal distance x from the centre line and the depth z. The soil is a homogeneous, isotropic, linearly elastic half-space.

An element dr of the strip is a line load q·dr, for which Flamant (1892) gave the stresses from Boussinesq’s (1883) solution (see stress below a line load). With b = B/2, integrating over the width:

Δσz=∫−bb2qz3π[(x−r)2+z2]2dr=qπ[F(x+b)−F(x−b)]
F(u)=tan−1uz+zuu2+z2

Written with the antiderivative F, the expression holds everywhere, below the strip and beside it, without a correction of the arctangent; the GeoTerva strip module evaluates it in this form. The arctangents are in radians.

2The angle formΔσz, Δσx and τxz with α and δ.

The same integration gives the horizontal and the shear stress, and all three are written most compactly with two angles: α, the angle the strip subtends at the point, and δ, the angle between the vertical through the point and the line to the nearer edge of the strip, negative when the point lies below the strip:

Δσz=qπ[α+sin⁡αcos⁡(α+2δ)]
Δσx=qπ[α−sin⁡αcos⁡(α+2δ)]
τxz=qπsin⁡αsin⁡(α+2δ)
α=tan−1|x|+bz−tan−1|x|−bz,δ=tan−1|x|−bz

τxz is given for x ≥ 0 and changes sign across the centre line, where it is zero. The principal stresses take a particularly simple form; the major one acts along the bisector of the angle α:

σ1,3=qπ(α±sin⁡α),τmax=qπsin⁡α

All points from which the strip is seen under the same angle α lie on a circle through its two edges, so the lines of equal principal stress are circles. The largest shear stress, q/π = 0.318q, occurs where α = 90°: on the semicircle that has the strip as its diameter, whose lowest point is at the depth z = B/2 below the centre.

3Tables of the stressesΔσz/q everywhere; all three below the centre and the edge.

Table 1. Δσz/q below a uniform strip load: z/B down, x/B across (x from the centre line)
z/B \ x/B00.250.50.7511.523
0.10.9970.9880.5000.0110.0020.0000.0000.000
0.250.9590.9020.4970.0890.0190.0030.0010.000
0.50.8180.7350.4800.2140.0840.0170.0050.001
0.750.6680.6070.4480.2710.1460.0420.0150.003
10.5500.5100.4090.2880.1850.0710.0290.007
1.250.4620.4360.3700.2850.2050.0950.0440.012
1.50.3960.3790.3340.2740.2110.1140.0590.018
20.3060.2980.2750.2420.2050.1340.0830.031
2.50.2480.2440.2310.2120.1880.1390.0970.044
30.2080.2060.1980.1860.1710.1360.1030.054
40.1580.1560.1530.1470.1400.1220.1020.066
50.1260.1260.1240.1210.1170.1070.0950.069
60.1060.1050.1040.1020.1000.0940.0860.068

x/B = 0.5 is the edge of the strip; the table is symmetric about the centre line. Values computed by GeoTerva with the function its strip load module uses.

Below the centre the vertical stress falls to q/2 at z = 1.13B, to 0.2q at 3.13B and to 0.1q only at 6.34B, against 2.09B below the centre of a square footing of the same width: the pressure bulb of a long load reaches much deeper.

Table 2. Δσz/q, Δσx/q and τxz/q below the centre line and below the edge
z/BΔσz/q centreΔσx/q centreΔσz/q edgeΔσx/q edgeτxz/q edge
0.10.9970.7520.5000.4370.315
0.250.9590.4500.4970.3470.300
0.50.8180.1820.4800.2250.255
0.750.6680.0810.4480.1420.204
10.5500.0410.4090.0910.159
1.250.4620.0230.3700.0600.124
1.50.3960.0140.3340.0400.098
20.3060.0060.2750.0200.064
2.50.2480.0030.2310.0110.044
30.2080.0020.1980.0070.032
40.1580.0010.1530.0030.019
50.1260.0000.1240.0020.012
60.1060.0000.1040.0010.009

Below the centre τxz = 0. Δσz: the strip module’s function; Δσx and τxz: the angle form, checked by GeoTerva against a numerical integration of the line-load stresses.

4Worked exampleA wall footing 2.4 m wide at 160 kPa.

A long wall footing B = 2.4 m wide applies q = 160 kPa. Find the stresses at z = 3 m below the centre line, below the edge (x = 1.2 m) and at x = 3.0 m, 1.8 m beyond the edge. Here b = 1.2 m.

  • Below the centre: δ = tan−1(−1.2/3.0) = −21.80°, α = 2 × 21.80° = 43.60° = 0.7610 rad, so α + 2δ = 0 and Δσz = (160/π)(0.7610 + sin 43.60°) = 73.9 kPa, Δσx = (160/π)(0.7610 − 0.6897) = 3.6 kPa, τxz = 0.
  • Below the edge: δ = 0, α = tan−1(2.4/3.0) = 38.66°: Δσz = 59.2 kPa, Δσx = 9.5 kPa, τxz = 19.9 kPa.
  • Beside the strip (x = 3.0 m): δ = tan−1(1.8/3.0) = 30.96°, α = tan−1(4.2/3.0) − δ = 23.50°: Δσz = 22.5 kPa, Δσx = 19.3 kPa, τxz = 20.2 kPa.
Table 3. The worked example: stresses (kPa) at z = 3 m
x (m)α (°)δ (°)ΔσzΔσxτxzσ1σ3
0.043.60−21.8073.93.60.073.93.6
1.238.660.0059.29.519.966.22.5
3.023.5030.9622.519.320.241.20.6

σ1, σ3: the principal stress increases (q/π)(α ± sin α). Values computed by GeoTerva.

Below the centre Δσx is only 5 % of Δσz; beside the strip it is 86 %: away from the centre line the load pushes the soil sideways almost as much as down. Several parallel strips, each with its own pressure and width, add point by point; an embankment is a uniform strip with two triangular ones (see stress below an embankment).

5QuestionsShort answers.

When can a long footing be treated as a strip?

When it is long compared with its width and with the depth of interest. Below the centre at z = 2B, a rectangle of length L = 2B gives 62 % of the strip value, L = 5B 93 % and L = 10B 99 % (corner factors as in stress below a rectangular footing); the deeper the point, the longer the rectangle must be.

Where is the shear stress below a strip load largest?

On the semicircle through the two edges of the strip, where the strip is seen under a right angle (α = 90°): there τmax = q/π, about 0.32q. Directly below the centre at the surface it is zero, since there α = 180°.

Does Δσz include the weight of the soil?

No. The strip-load stresses are the increases caused by the load alone; the overburden pressure at the depth of the point, and the pore pressure, are added separately to obtain the total and the effective stresses.

The theory behind it