GeoTerva Open the module

Formulas and tables · Stress distribution

Stress below an embankment: Osterberg’s influence factor

The vertical stress a road or railway embankment, a levee or a long stockpile causes in the ground: Osterberg’s influence factor for a half embankment, its table against a/z and b/z, and how the halves add up below the crest, the slopes and beyond the toe.

  • Free to read
  • a/z = 0.05–10
  • b/z = 0–3
  • Worked example

1The embankment loadA trapezoid, γH under the crest.

An embankment of height H and unit weight γ loads the ground with q0 = γH under its crest; under each side slope the load falls linearly to zero at the toe. The fill is treated as a flexible load on the surface of a homogeneous, isotropic, linearly elastic half-space; its own stiffness is ignored. The embankment is long, so the problem is two-dimensional (plane strain), and Δσz is the increase caused by the fill alone.

2Osterberg’s solutionThe influence factor of a half embankment.

Osterberg (1957) gave, from the elastic solution for a half-space, the vertical stress below half an embankment: a ramp of horizontal width a rising from zero to q0, followed by a uniform part of width b. The point lies at depth z on the vertical through the far end of the uniform part (for a symmetric embankment, the centre line, b being half the crest width):

Δσz=q0I,I=1π[a+ba(α1+α2)−baα2]
α1=tan−1a+bz−tan−1bz,α2=tan−1bz

The angles are in radians. I depends only on a/z and b/z and never exceeds 0.5: one half of a very wide embankment carries half of q0 to the point. With b = 0 the half embankment is a plain ramp, and I = α1/π. (The embankment module of GeoTerva calls the two widths B2 = a and B1 = b.)

3Superposition of halvesBelow the crest, below a slope, beyond the toe.

The soil being elastic, any point is reached by adding and subtracting half embankments, each written as I(a, b). Let al and ar be the widths of the left and right slopes and Bc the crest width.

  • Below the crest, at the distances bl and br from the left and right crest edges:
Δσz=q0[I(al,bl)+I(ar,br)]
  • Beyond the right toe, at the distance d from it: the crest is extended to the point, and the missing load, a half embankment of slope ar and crest d, is subtracted (at the toe, d = 0):
Δσz=q0[I(al,Bc+ar+d)−I(ar,d)]
  • Below the right slope, at the distance s from the crest edge: the crest is extended to the point, the missing ramp of width s is subtracted, and the slope that remains beyond the point is a ramp of height q0(1 − s/ar):
Δσz=q0[I(al,Bc+s)−sarI(s,0)+(1−sar)I(ar−s,0)]

The GeoTerva module does the same with three strips and no case distinctions: a uniform strip q0 under the crest and two triangular strips under the slopes (see stress below a strip load). The two routes give the same stress at every point; the worked example below checks it for each case.

4Table of the influence factora/z down, b/z across.

Table 1. Osterberg’s influence factor I for a half embankment: a/z down, b/z across
a/z \ b/z00.10.20.40.60.811.523
0.050.0160.0790.1390.2420.3210.3760.4130.4610.4800.493
0.10.0320.0940.1530.2530.3290.3810.4170.4630.4810.493
0.20.0630.1230.1790.2740.3430.3910.4230.4650.4820.494
0.30.0930.1510.2040.2920.3560.3990.4290.4670.4830.494
0.50.1480.2000.2470.3230.3770.4140.4380.4710.4850.494
0.70.1940.2410.2820.3470.3940.4250.4460.4740.4860.495
10.2500.2880.3220.3750.4120.4380.4550.4780.4880.495
1.50.3130.3420.3660.4060.4330.4520.4650.4820.4900.496
20.3520.3750.3940.4250.4460.4610.4710.4850.4920.497
30.3980.4130.4260.4470.4620.4720.4790.4890.4940.497
50.4370.4470.4550.4670.4760.4830.4870.4930.4960.498
100.4680.4730.4770.4830.4880.4910.4930.4960.4980.499

a: horizontal width of the slope; b: width of the crest part between the top of the slope and the vertical through the point. Δσz = q0I for one half. Values computed by GeoTerva with the function its embankment module uses.

5Worked exampleA road embankment 4.5 m high.

A road embankment H = 4.5 m high is built of fill with γ = 19 kN/m³, so q0 = 19 × 4.5 = 85.5 kPa. The crest is 12 m wide and the side slopes are 2 horizontal to 1 vertical, so a = 9 m on both sides. Find Δσz at z = 5 m.

  • Below the centre line (b = 6 m): α2 = tan−1(6/5) = 50.19°, α1 = tan−1(15/5) − α2 = 21.37°; I = (1/π)[(15/9)(1.2490) − (6/9)(0.8761)] = 0.4767. Δσz = 2 × 85.5 × 0.4767 = 81.5 kPa.
  • Below the crest edge: I(9, 12) + I(9, 0) = 0.4939 + 0.3386, Δσz = 71.2 kPa.
  • Below the slope, s = 3 m from the crest edge: I(9, 15) − (3/9)·I(3, 0) + (1 − 3/9)·I(6, 0) = 0.4963 − 0.0573 + 0.1859, Δσz = 53.4 kPa.
  • Below the toe: I(9, 21) − I(9, 0) = 0.4984 − 0.3386, Δσz = 13.7 kPa.
  • 3 m beyond the toe: I(9, 24) − I(9, 3) = 0.4988 − 0.4418, Δσz = 4.9 kPa.

The three-strip sum of the module gives the same five values. Below the centre the stress at this depth is still 95 % of q0; it decreases slowly with depth, because the embankment is wide and long:

Table 2. The worked example: Δσz against depth below the centre line and below the toe
z (m)Δσz centre (kPa)Δσz/q0 centreΔσz toe (kPa)Δσz/q0 toe
185.50.9993.00.035
2.584.80.9927.40.086
581.50.95313.70.160
7.576.00.88818.50.216
1069.50.81321.80.255
1557.40.67225.40.297
2047.80.55926.20.307
3034.90.40824.50.287

q0 = 85.5 kPa, crest 12 m, slopes 9 m. Values computed by GeoTerva with the function its embankment module uses.

6QuestionsShort answers.

What are a and b in Osterberg’s chart?

a is the horizontal width of the side slope and b the width of the crest between the top of that slope and the vertical through the point; for a point on the centre line of a symmetric embankment, b is half the crest width. Both are divided by the depth z of the point.

What is the largest value of the influence factor?

0.5 for one half. When a and b are large compared with z, each half contributes q0/2 and the stress below the centre approaches q0: for a/z = b/z = 10, I = 0.4999.

Does the solution account for the stiffness of the fill?

No. The embankment is a flexible load γH on an elastic half-space, which is the usual basis for the stress increase in a settlement estimate. A stiff or reinforced fill spreads its load somewhat differently, and the stability of the embankment on soft ground is a separate check.

The theory behind it