1The unit skin frictionf = Kσ′otanδ′ along the shaft.
The skin (shaft) resistance of a pile is the unit friction f summed over the surface of the shaft:
p is the perimeter of the section and ΔL a length of shaft over which p and f are taken as constant. In a sand the unit friction is the horizontal effective stress on the shaft times the friction coefficient of the pile–soil interface:
σ′o is the effective vertical stress at depth z, K the effective earth-pressure coefficient on the shaft and δ′ the pile–soil friction angle. The product K·tanδ′ is the β of the β method for sands, so the same equation is also written f = βσ′o. In reality K varies with depth: it is roughly the Rankine passive coefficient near the head and may fall below the at-rest value deeper down, so an average is used for the whole shaft.
2K and δ′ by installationBored, low-displacement and high-displacement piles.
How a pile is put into the ground changes the sand around it. Driving densifies it, to some 2.5 pile diameters from the shaft; a high-displacement pile (a closed-ended pipe, a precast concrete pile) earns more friction in a loose sand than a low-displacement one (an H-pile, an open-ended pipe); boring or jetting loosens the sand and earns less. The averages recommended for K follow the installation, with Ko = 1 − sinφ′:
| Pile type | K | At φ′ = 34° |
|---|---|---|
| Bored or jetted | ≈ Ko | 0.44 |
| Low-displacement driven | Ko to 1.4Ko | 0.44 to 0.62 |
| High-displacement driven | Ko to 1.8Ko | 0.44 to 0.79 |
From field load tests, Mansur and Hunter (1970) report average values of K = 1.65 for H-piles, 1.26 for steel pipe piles and 1.5 for precast concrete piles. The pile–soil friction angle lies between 0.5φ′ and 0.8φ′ according to the various investigations.
Both K and δ′ are judgements about the pile rather than properties of the sand, so the GeoTerva pile modules ask for them and fill in a default: δ′ = 0.75φ′ of each sand layer, and K = Ko of the layer for a bored pile or 1.4Ko for a driven or jacked one. Both boxes stay editable, and the modules caution when K is far above Ko for a bored pile.
3The critical depth L′ = 15DWhy the friction stops growing.
Measured unit friction does not keep growing with depth as the effective stress does. It increases roughly linearly to a depth L′ and stays nearly constant below it; L′ is fifteen to twenty pile diameters, and the conservative estimate is
The usual explanation is arching: below a certain depth the sand round the shaft no longer passes the full overburden on to it. The K–δ method therefore holds σ′o at its value at L′ from there to the tip:
The critical depth belongs to the pile, not to a layer: in a layered profile (the pile capacity in layered soil module) a sand layer that lies wholly below L′ carries the same σ′o over its whole thickness. It is a different thing from the limit on the point resistance in Meyerhof’s method, which caps a stress, not a depth. Coyle and Castello’s shaft method has no critical depth at all: the averaging over the whole length and a K that falls with L/D play that part.
4Table of K·tanδ′, φ′ = 25–40°Bored and driven piles, δ′ = 0.75φ′.
| φ′ (°) | Ko = 1 − sinφ′ | δ′ = 0.75φ′ (°) | δ′ range 0.5–0.8φ′ (°) | K·tanδ′, K = Ko (bored) | K·tanδ′, K = 1.4Ko (driven) | K·tanδ′, K = 1.8Ko (high-displacement) |
|---|---|---|---|---|---|---|
| 25 | 0.577 | 18.8 | 12.5–20.0 | 0.197 | 0.275 | 0.354 |
| 26 | 0.562 | 19.5 | 13.0–20.8 | 0.199 | 0.278 | 0.358 |
| 27 | 0.546 | 20.3 | 13.5–21.6 | 0.202 | 0.283 | 0.364 |
| 28 | 0.531 | 21.0 | 14.0–22.4 | 0.204 | 0.285 | 0.367 |
| 29 | 0.515 | 21.8 | 14.5–23.2 | 0.206 | 0.288 | 0.371 |
| 30 | 0.500 | 22.5 | 15.0–24.0 | 0.207 | 0.290 | 0.373 |
| 31 | 0.485 | 23.3 | 15.5–24.8 | 0.209 | 0.292 | 0.376 |
| 32 | 0.470 | 24.0 | 16.0–25.6 | 0.209 | 0.293 | 0.377 |
| 33 | 0.455 | 24.8 | 16.5–26.4 | 0.210 | 0.295 | 0.379 |
| 34 | 0.441 | 25.5 | 17.0–27.2 | 0.210 | 0.294 | 0.378 |
| 35 | 0.426 | 26.3 | 17.5–28.0 | 0.211 | 0.295 | 0.379 |
| 36 | 0.412 | 27.0 | 18.0–28.8 | 0.210 | 0.294 | 0.378 |
| 37 | 0.398 | 27.8 | 18.5–29.6 | 0.210 | 0.294 | 0.378 |
| 38 | 0.384 | 28.5 | 19.0–30.4 | 0.209 | 0.292 | 0.376 |
| 39 | 0.371 | 29.3 | 19.5–31.2 | 0.208 | 0.291 | 0.374 |
| 40 | 0.357 | 30.0 | 20.0–32.0 | 0.206 | 0.289 | 0.371 |
Multiply K·tanδ′ by the effective vertical stress σ′o (held at its value at L′ = 15D below that depth) to get the unit friction f in the same units. δ′ is rounded to 0.1°, as the GeoTerva modules fill it in. Values computed by GeoTerva.
5Worked exampleA driven pile, 0.45 m in diameter, 13.5 m long.
A driven concrete pile of circular section, D = 0.45 m, is embedded L = 13.5 m in a sand with φ′ = 34°, γ = 18 kN/m³ above the water table at 3.0 m depth and γsat = 20 kN/m³ below it (γw = 9.81 kN/m³). p = πD = 1.414 m.
- K and δ′: Ko = 1 − sin 34° = 0.441; for a driven pile K = 1.4 × 0.441 = 0.62 (to two decimals); δ′ = 0.75 × 34° = 25.5°.
- Critical depth: L′ = 15 × 0.45 = 6.75 m. σ′o = 54.0 kPa at the water table and 92.2 kPa at L′; below L′ it is held at 92.2 kPa.
- Unit friction below L′: f = 0.62 × 92.2 × tan 25.5° = 27.3 kPa (without the limit it would reach 47.6 kPa at the tip).
- Area of the stress diagram: ½ × 54.0 × 3.0 + ½ × (54.0 + 92.2) × 3.75 + 92.2 × 6.75 = 355.1 + 622.4 = 977.6 kN/m.
- Skin resistance: Qs = 1.414 × 0.62 × tan 25.5° × 977.6 = 409 kN.
Bored instead of driven (K = Ko = 0.44), the same shaft gives 290 kN. Coyle and Castello’s method (K = 0.81, δ′ = 0.8φ′, no critical depth) gives 712 kN for the driven pile. With Meyerhof’s point of 617 kN, Qu = 617 + 409 = 1026 kN and, with a factor of safety of 3, Qall = 342 kN.
6QuestionsShort answers.
What K should be used for a driven pile in sand?
Between Ko and 1.4Ko for a low-displacement pile (an H-pile, an open-ended pipe) and between Ko and 1.8Ko for a high-displacement one (a closed-ended pipe, a precast concrete pile), with Ko = 1 − sinφ′. At φ′ = 34° that is 0.44 to 0.62 and 0.44 to 0.79. For a bored or jetted pile K ≈ Ko.
What is the critical depth for skin friction?
The depth L′ below which the unit friction stops growing. It is fifteen to twenty pile diameters, and L′ = 15D is the conservative value used in the K–δ method: 6.75 m for a pile 0.45 m in diameter.
What friction angle δ′ should be used between the pile and the sand?
The investigations put δ′ between 0.5φ′ and 0.8φ′, rougher surfaces towards the upper end. GeoTerva fills in δ′ = 0.75φ′ and lets you change it; at φ′ = 34° the range is 17.0° to 27.2° and the default 25.5°.