1A vertical wall, sloping backfillRankine (1857): the stress parallel to the surface.
Rankine (1857) found the stresses in a semi-infinite mass of granular soil (c′ = 0) whose surface slopes at α to the horizontal, at the moment it fails by spreading (active) or by compression (passive). On any vertical plane the stress acts parallel to the ground surface and grows linearly with depth. A frictionless vertical wall that takes the place of such a plane carries the thrust
Both forces act at H/3 above the base, inclined at α: the horizontal component is Pa cos α, the vertical component Pa sin α, downward on the wall for a backfill rising away from it. With α = 0 the coefficients are tan²(45° ∓ φ′/2), the level-ground values of the earth pressure coefficients page.
The root needs α ≤ φ′: a slope steeper than φ′ cannot stand. At α = φ′ the root vanishes and both coefficients become cos φ′ (for φ′ = 30°, Ka = Kp = 0.866): the slope itself is at failure, and the active and passive states coincide.
2The general case: an inclined backChu (1991).
Chu (1991) extended Rankine’s solution to a frictionless wall whose back is inclined at θ to the vertical, behind a granular backfill sloping at α. θ is positive when the heel lies farther into the backfill than the top of the wall, so that the soil rests on the back; negative when the back leans out over the soil. The active thrust is Pa = ½γH²Ka(R), with H the vertical height of the wall, and
The thrust acts at H/3 above the heel, inclined at β to the normal of the back, and the failure wedge is bounded by a plane at η to the horizontal:
For the passive case the signs change:
With θ = 0 they return the vertical-back coefficients above, with β = α. With a level backfill the coefficient is the same for ±θ but the thrust turns the other way: for φ′ = 30° and θ = ±10°, Ka(R) = 0.377 with β = 17.9° and −17.9°.
3Table of KaVertical back, φ′ = 20–45°, α = 0–35°.
| φ′ | α = 0° | α = 5° | α = 10° | α = 15° | α = 20° | α = 25° | α = 30° | α = 35° |
|---|---|---|---|---|---|---|---|---|
| 20° | 0.490 | 0.500 | 0.531 | 0.603 | 0.940 | — | — | — |
| 21° | 0.472 | 0.481 | 0.509 | 0.571 | 0.748 | — | — | — |
| 22° | 0.455 | 0.463 | 0.488 | 0.543 | 0.677 | — | — | — |
| 23° | 0.438 | 0.445 | 0.468 | 0.517 | 0.625 | — | — | — |
| 24° | 0.422 | 0.428 | 0.449 | 0.492 | 0.583 | — | — | — |
| 25° | 0.406 | 0.412 | 0.431 | 0.469 | 0.547 | 0.906 | — | — |
| 26° | 0.390 | 0.396 | 0.413 | 0.448 | 0.515 | 0.700 | — | — |
| 27° | 0.376 | 0.380 | 0.396 | 0.428 | 0.487 | 0.626 | — | — |
| 28° | 0.361 | 0.366 | 0.380 | 0.409 | 0.460 | 0.573 | — | — |
| 29° | 0.347 | 0.351 | 0.365 | 0.390 | 0.436 | 0.530 | — | — |
| 30° | 0.333 | 0.337 | 0.350 | 0.373 | 0.414 | 0.494 | 0.866 | — |
| 31° | 0.320 | 0.324 | 0.335 | 0.356 | 0.393 | 0.462 | 0.650 | — |
| 32° | 0.307 | 0.311 | 0.321 | 0.341 | 0.374 | 0.434 | 0.574 | — |
| 33° | 0.295 | 0.298 | 0.307 | 0.325 | 0.355 | 0.408 | 0.520 | — |
| 34° | 0.283 | 0.286 | 0.294 | 0.311 | 0.338 | 0.385 | 0.478 | — |
| 35° | 0.271 | 0.274 | 0.282 | 0.297 | 0.322 | 0.363 | 0.442 | 0.819 |
| 36° | 0.260 | 0.262 | 0.270 | 0.283 | 0.306 | 0.343 | 0.411 | 0.597 |
| 37° | 0.249 | 0.251 | 0.258 | 0.270 | 0.291 | 0.324 | 0.383 | 0.521 |
| 38° | 0.238 | 0.240 | 0.246 | 0.258 | 0.277 | 0.307 | 0.358 | 0.468 |
| 39° | 0.228 | 0.229 | 0.235 | 0.246 | 0.263 | 0.291 | 0.336 | 0.426 |
| 40° | 0.217 | 0.219 | 0.225 | 0.235 | 0.250 | 0.275 | 0.315 | 0.391 |
| 41° | 0.208 | 0.209 | 0.214 | 0.224 | 0.238 | 0.260 | 0.296 | 0.361 |
| 42° | 0.198 | 0.200 | 0.204 | 0.213 | 0.226 | 0.246 | 0.278 | 0.334 |
| 43° | 0.189 | 0.190 | 0.195 | 0.203 | 0.215 | 0.233 | 0.262 | 0.310 |
| 44° | 0.180 | 0.181 | 0.186 | 0.193 | 0.204 | 0.221 | 0.247 | 0.289 |
| 45° | 0.172 | 0.173 | 0.177 | 0.183 | 0.193 | 0.209 | 0.232 | 0.270 |
The thrust Pa = ½KaγH² acts parallel to the surface. — : α > φ′, no solution. Values computed by GeoTerva with the function its Rankine sloping backfill module uses.
4Table of KpVertical back, φ′ = 20–45°, α = 0–35°.
| φ′ | α = 0° | α = 5° | α = 10° | α = 15° | α = 20° | α = 25° | α = 30° | α = 35° |
|---|---|---|---|---|---|---|---|---|
| 20° | 2.040 | 1.986 | 1.826 | 1.548 | 0.940 | — | — | — |
| 21° | 2.117 | 2.064 | 1.905 | 1.633 | 1.181 | — | — | — |
| 22° | 2.198 | 2.145 | 1.986 | 1.719 | 1.305 | — | — | — |
| 23° | 2.283 | 2.230 | 2.071 | 1.806 | 1.413 | — | — | — |
| 24° | 2.371 | 2.318 | 2.159 | 1.895 | 1.515 | — | — | — |
| 25° | 2.464 | 2.410 | 2.251 | 1.987 | 1.614 | 0.906 | — | — |
| 26° | 2.561 | 2.507 | 2.346 | 2.083 | 1.714 | 1.174 | — | — |
| 27° | 2.663 | 2.608 | 2.446 | 2.181 | 1.815 | 1.312 | — | — |
| 28° | 2.770 | 2.715 | 2.551 | 2.284 | 1.918 | 1.434 | — | — |
| 29° | 2.882 | 2.826 | 2.660 | 2.390 | 2.023 | 1.550 | — | — |
| 30° | 3.000 | 2.943 | 2.775 | 2.502 | 2.132 | 1.664 | 0.866 | — |
| 31° | 3.124 | 3.066 | 2.895 | 2.618 | 2.245 | 1.778 | 1.154 | — |
| 32° | 3.255 | 3.196 | 3.022 | 2.740 | 2.362 | 1.894 | 1.306 | — |
| 33° | 3.392 | 3.332 | 3.155 | 2.868 | 2.484 | 2.013 | 1.441 | — |
| 34° | 3.537 | 3.476 | 3.295 | 3.002 | 2.612 | 2.135 | 1.570 | — |
| 35° | 3.690 | 3.627 | 3.442 | 3.144 | 2.745 | 2.262 | 1.698 | 0.819 |
| 36° | 3.852 | 3.788 | 3.598 | 3.293 | 2.886 | 2.394 | 1.827 | 1.124 |
| 37° | 4.023 | 3.957 | 3.762 | 3.450 | 3.033 | 2.532 | 1.958 | 1.288 |
| 38° | 4.204 | 4.136 | 3.936 | 3.615 | 3.189 | 2.676 | 2.094 | 1.435 |
| 39° | 4.395 | 4.326 | 4.121 | 3.791 | 3.353 | 2.827 | 2.234 | 1.576 |
| 40° | 4.599 | 4.527 | 4.316 | 3.977 | 3.526 | 2.987 | 2.380 | 1.718 |
| 41° | 4.815 | 4.741 | 4.523 | 4.174 | 3.710 | 3.155 | 2.533 | 1.861 |
| 42° | 5.045 | 4.968 | 4.744 | 4.383 | 3.904 | 3.333 | 2.694 | 2.009 |
| 43° | 5.289 | 5.210 | 4.978 | 4.605 | 4.111 | 3.521 | 2.863 | 2.162 |
| 44° | 5.550 | 5.468 | 5.228 | 4.842 | 4.331 | 3.721 | 3.042 | 2.322 |
| 45° | 5.828 | 5.744 | 5.495 | 5.095 | 4.565 | 3.934 | 3.232 | 2.489 |
α is measured upward away from the wall, as in Table 1. Values computed by GeoTerva.
5Table for an inclined backChu (1991), φ′ = 34°.
| θ | α = 0° | α = 10° | α = 20° | α = 30° |
|---|---|---|---|---|
| −10° | 0.333 (−22.0°) | 0.299 (−14.3°) | 0.285 (−2.9°) | 0.335 (15.9°) |
| −5° | 0.296 (−12.2°) | 0.283 (−2.4°) | 0.299 (9.5°) | 0.396 (24.5°) |
| 0° | 0.283 (0.0°) | 0.294 (10.0°) | 0.338 (20.0°) | 0.478 (30.0°) |
| 5° | 0.296 (12.2°) | 0.331 (20.3°) | 0.400 (27.2°) | 0.578 (32.9°) |
| 10° | 0.333 (22.0°) | 0.388 (27.5°) | 0.481 (31.5°) | 0.697 (34.0°) |
| 15° | 0.390 (28.5°) | 0.463 (31.6°) | 0.578 (33.6°) | 0.836 (33.7°) |
| 20° | 0.461 (32.2°) | 0.553 (33.6°) | 0.693 (34.0°) | 0.996 (32.5°) |
θ > 0: the heel farther into the backfill than the top (the soil rests on the back). Pa = ½γH²Ka(R) with H the vertical height. Values computed by GeoTerva after Chu (1991).
6Worked exampleA battered back behind a sloping backfill.
A wall H = 6 m high has its back inclined at θ = 10° (the heel 1.06 m farther into the fill than the top) and retains a granular backfill sloping at α = 15°, with φ′ = 34° and γ = 19 kN/m³.
- Angle ψa: sin−1(sin 15°/sin 34°) = 27.57°, so ψa = 27.57° − 15° + 2 × 10° = 32.57°.
- Coefficient: Ka(R) = 0.428, against 0.311 for a vertical back behind the same slope.
- Thrust: Pa = ½ × 19 × 6² × 0.428 = 146.2 kN/m, at H/3 = 2.00 m above the heel.
- Direction: β = 29.65° to the normal of the back. The normal itself points 10° below the horizontal, so the thrust is inclined 39.65° below the horizontal: Ph = 112.6 kN/m, Pv = 93.3 kN/m.
- Failure wedge: its plane rises from the heel at η = 55.7° to the horizontal.
Against a vertical back the same slope gives Pa = 106.3 kN/m at α = 15° (Ph = 102.7, Pv = 27.5 kN/m). The battered back carries part of the weight of the soil resting on it, which shows in the much larger vertical component. Pushed into the same fill, the battered back would mobilise Kp(R) = 3.345 at β = 8.1°. In the stability check of a cantilever or gravity wall the Rankine pressure is usually taken on the vertical plane through the heel instead, with the soil above the heel counted as weight (see retaining wall stability checks).
7QuestionsShort answers.
In which direction does the Rankine thrust act behind a sloping backfill?
On a vertical back it is parallel to the ground surface, inclined at α to the horizontal, at H/3 above the base. On a back inclined at θ it makes the angle β of Chu (1991) with the normal of the back.
What happens when the backfill slope reaches φ′?
Ka and Kp both become cos φ′, and for α > φ′ there is no solution: a granular slope steeper than its friction angle cannot stand, with or without a wall.
Does the sloping-backfill solution include wall friction?
The wall is frictionless in Rankine’s theory, but the thrust is inclined as if a wall friction δ = α acted on a vertical back. Coulomb’s wedge with δ = α on a vertical back gives the same coefficient: for φ′ = 32° and α = 10°, 0.321 against Rankine’s 0.321.