1The problem Steinbrenner solvedThe settlement of a corner, in closed form.
A foundation settles as soon as it is loaded, before any water has had time to leave a clay. For this immediate (elastic) settlement the ground is treated as a linear elastic body, and the settlement of a point at the loaded level is the integral of the vertical strain below it:
The stress increases are those of Boussinesq’s elastic half-space (see Boussinesq point load and stress below a rectangular footing). Steinbrenner (1934) integrated this strain in closed form below the corner of a flexible rectangle B′ × L′ carrying a uniform pressure q, from the surface down to a depth H at which a rigid base stops the strain:
E and ν are the modulus and Poisson’s ratio of the layer. The result is the settlement of a perfectly flexible area, which follows the soil; a stiff footing evens it out, as shown further down. F1 and F2 are dimensionless and depend only on the shape of the rectangle and on the thickness of the layer.
2F1 and F2Functions of m′ = L′/B′ and n′ = H/B′.
With B′ the shorter side of the corner rectangle, m′ = L′/B′ ≥ 1 and n′ = H/B′:
For a strip (m′ → ∞) the factors take the limits
As the layer gets thicker F1 grows, while F2 of a rectangle passes a maximum and dies away (for a strip it tends to 1/(2π) = 0.159). For a square corner F1 tends to 0.561 on an elastic half-space (n′ → ∞), the value of a flexible square on deep ground; for a strip it grows without bound (0.735 at n′ = 10, 0.954 at n′ = 20), since an infinitely long load on an infinitely deep elastic body has no finite settlement. This is why a strip footing is always computed down to a chosen depth.
3Tables of F1 and F2n′ = 0.25–20, m′ = 1 to strip.
| n′ \ m′ | 1 | 1.2 | 1.5 | 2 | 2.5 | 3 | 4 | 5 | 10 | strip |
|---|---|---|---|---|---|---|---|---|---|---|
| 0.25 | 0.014 | 0.013 | 0.012 | 0.011 | 0.010 | 0.010 | 0.010 | 0.010 | 0.010 | 0.010 |
| 0.5 | 0.049 | 0.046 | 0.043 | 0.040 | 0.038 | 0.038 | 0.037 | 0.036 | 0.036 | 0.036 |
| 0.75 | 0.095 | 0.090 | 0.085 | 0.080 | 0.077 | 0.076 | 0.074 | 0.073 | 0.071 | 0.071 |
| 1 | 0.142 | 0.138 | 0.132 | 0.125 | 0.121 | 0.118 | 0.115 | 0.113 | 0.111 | 0.110 |
| 1.5 | 0.224 | 0.224 | 0.220 | 0.213 | 0.207 | 0.203 | 0.197 | 0.194 | 0.189 | 0.188 |
| 2 | 0.285 | 0.290 | 0.292 | 0.289 | 0.284 | 0.279 | 0.271 | 0.267 | 0.259 | 0.256 |
| 2.5 | 0.330 | 0.341 | 0.349 | 0.351 | 0.348 | 0.344 | 0.336 | 0.331 | 0.320 | 0.315 |
| 3 | 0.363 | 0.379 | 0.393 | 0.402 | 0.402 | 0.400 | 0.392 | 0.386 | 0.373 | 0.366 |
| 4 | 0.408 | 0.431 | 0.455 | 0.476 | 0.484 | 0.487 | 0.484 | 0.479 | 0.462 | 0.451 |
| 5 | 0.437 | 0.465 | 0.496 | 0.526 | 0.543 | 0.551 | 0.554 | 0.552 | 0.534 | 0.519 |
| 6 | 0.457 | 0.489 | 0.524 | 0.563 | 0.585 | 0.598 | 0.609 | 0.610 | 0.595 | 0.575 |
| 7 | 0.471 | 0.506 | 0.545 | 0.590 | 0.618 | 0.635 | 0.653 | 0.658 | 0.647 | 0.623 |
| 8 | 0.482 | 0.519 | 0.561 | 0.611 | 0.643 | 0.664 | 0.688 | 0.697 | 0.692 | 0.664 |
| 10 | 0.498 | 0.537 | 0.584 | 0.641 | 0.679 | 0.707 | 0.740 | 0.758 | 0.768 | 0.735 |
| 15 | 0.519 | 0.562 | 0.615 | 0.682 | 0.730 | 0.766 | 0.816 | 0.848 | 0.897 | 0.863 |
| 20 | 0.529 | 0.575 | 0.631 | 0.702 | 0.756 | 0.797 | 0.856 | 0.896 | 0.977 | 0.954 |
| n′ \ m′ | 1 | 1.2 | 1.5 | 2 | 2.5 | 3 | 4 | 5 | 10 | strip |
|---|---|---|---|---|---|---|---|---|---|---|
| 0.25 | 0.049 | 0.050 | 0.051 | 0.052 | 0.052 | 0.052 | 0.052 | 0.053 | 0.053 | 0.053 |
| 0.5 | 0.074 | 0.077 | 0.081 | 0.084 | 0.085 | 0.086 | 0.087 | 0.087 | 0.088 | 0.088 |
| 0.75 | 0.083 | 0.089 | 0.095 | 0.101 | 0.104 | 0.106 | 0.108 | 0.109 | 0.110 | 0.111 |
| 1 | 0.083 | 0.091 | 0.100 | 0.109 | 0.114 | 0.117 | 0.120 | 0.122 | 0.124 | 0.125 |
| 1.5 | 0.075 | 0.084 | 0.096 | 0.110 | 0.118 | 0.124 | 0.130 | 0.134 | 0.139 | 0.140 |
| 2 | 0.064 | 0.074 | 0.086 | 0.102 | 0.114 | 0.121 | 0.131 | 0.136 | 0.145 | 0.148 |
| 2.5 | 0.055 | 0.064 | 0.076 | 0.093 | 0.106 | 0.115 | 0.127 | 0.135 | 0.147 | 0.151 |
| 3 | 0.048 | 0.056 | 0.068 | 0.084 | 0.097 | 0.108 | 0.122 | 0.131 | 0.147 | 0.154 |
| 4 | 0.037 | 0.044 | 0.054 | 0.069 | 0.082 | 0.093 | 0.110 | 0.121 | 0.145 | 0.156 |
| 5 | 0.031 | 0.036 | 0.045 | 0.058 | 0.070 | 0.080 | 0.098 | 0.111 | 0.140 | 0.157 |
| 6 | 0.026 | 0.031 | 0.038 | 0.050 | 0.060 | 0.070 | 0.087 | 0.101 | 0.135 | 0.158 |
| 7 | 0.022 | 0.027 | 0.033 | 0.043 | 0.053 | 0.062 | 0.078 | 0.092 | 0.129 | 0.158 |
| 8 | 0.020 | 0.023 | 0.029 | 0.038 | 0.047 | 0.055 | 0.071 | 0.084 | 0.124 | 0.158 |
| 10 | 0.016 | 0.019 | 0.023 | 0.031 | 0.038 | 0.046 | 0.059 | 0.071 | 0.112 | 0.159 |
| 15 | 0.011 | 0.013 | 0.016 | 0.021 | 0.026 | 0.031 | 0.041 | 0.050 | 0.088 | 0.159 |
| 20 | 0.008 | 0.010 | 0.012 | 0.016 | 0.020 | 0.024 | 0.031 | 0.039 | 0.071 | 0.159 |
B′ is the shorter side of the loaded corner rectangle and H the thickness of the elastic layer below it. Values computed by GeoTerva with the functions its elastic settlement modules use.
Between the tabulated values F1 and F2 may be interpolated linearly; the GeoTerva modules do not interpolate but evaluate the formulas above for the exact m′ and n′.
4Poisson’s ratio and IsF2 vanishes for undrained clay.
Poisson’s ratio enters twice: through the factor (1 − ν²) in front and through the weight of F2 in Is, (1 − 2ν)/(1 − ν), which is 0.750 for ν = 0.2, 0.571 for ν = 0.3 and 0.333 for ν = 0.4. A saturated clay loaded faster than it can drain deforms at constant volume, ν = 0.5: the weight is zero, F2 drops out and Is = F1 (Table 1). For sand and gravel, which drain as they are loaded, ν′ is usually taken between 0.25 and 0.35.
| n′ | m′ = 1, ν = 0.2 | m′ = 1, ν = 0.3 | m′ = 1, ν = 0.4 | m′ = 2, ν = 0.2 | m′ = 2, ν = 0.3 | m′ = 2, ν = 0.4 |
|---|---|---|---|---|---|---|
| 0.25 | 0.050 | 0.041 | 0.030 | 0.049 | 0.040 | 0.028 |
| 0.5 | 0.104 | 0.091 | 0.073 | 0.103 | 0.088 | 0.068 |
| 0.75 | 0.157 | 0.142 | 0.122 | 0.156 | 0.138 | 0.114 |
| 1 | 0.204 | 0.190 | 0.170 | 0.207 | 0.187 | 0.161 |
| 1.5 | 0.280 | 0.267 | 0.249 | 0.295 | 0.276 | 0.250 |
| 2 | 0.333 | 0.322 | 0.306 | 0.366 | 0.348 | 0.323 |
| 2.5 | 0.371 | 0.361 | 0.348 | 0.421 | 0.405 | 0.382 |
| 3 | 0.399 | 0.390 | 0.379 | 0.465 | 0.450 | 0.430 |
| 4 | 0.436 | 0.430 | 0.421 | 0.528 | 0.515 | 0.499 |
| 5 | 0.460 | 0.455 | 0.447 | 0.570 | 0.560 | 0.546 |
| 6 | 0.476 | 0.472 | 0.466 | 0.600 | 0.591 | 0.579 |
| 7 | 0.488 | 0.484 | 0.479 | 0.622 | 0.615 | 0.604 |
| 8 | 0.497 | 0.494 | 0.489 | 0.639 | 0.633 | 0.623 |
| 10 | 0.510 | 0.507 | 0.503 | 0.664 | 0.658 | 0.651 |
| 15 | 0.527 | 0.525 | 0.522 | 0.697 | 0.694 | 0.689 |
| 20 | 0.535 | 0.534 | 0.532 | 0.714 | 0.712 | 0.708 |
For ν = 0.5, Is = F1 of Table 1. Values computed by GeoTerva.
5Centre, corner and rigid footingSuperposition of corner rectangles.
Steinbrenner’s factors give the settlement of a corner. Any other point at the surface is the corner of four rectangles, whose settlements add (or subtract, for a point outside the loaded area). For a flexible footing B × L:
- Centre: four rectangles B/2 × L/2, so B′ = B/2, m′ = L/B and n′ = 2H/B: S = 4·q·(B/2)·(1 − ν²)/E·Is.
- Corner: the whole rectangle, B′ = B, m′ = L/B and n′ = H/B: S = q·B·(1 − ν²)/E·Is.
- Edge of a strip: two semi-infinite strips, S = 2·q·B·(1 − ν²)/E·Is with the strip factors.
Written as S = qB(1 − ν²)/E · Ic, the centre factor Ic = 2Is(L/B, 2H/B) is:
| H/B | L/B = 1, ν = 0.3 | L/B = 1, ν = 0.5 | L/B = 2, ν = 0.3 | L/B = 2, ν = 0.5 | L/B = 5, ν = 0.3 | L/B = 5, ν = 0.5 |
|---|---|---|---|---|---|---|
| 0.5 | 0.379 | 0.284 | 0.375 | 0.250 | 0.366 | 0.227 |
| 1 | 0.643 | 0.570 | 0.695 | 0.578 | 0.689 | 0.534 |
| 1.5 | 0.781 | 0.726 | 0.899 | 0.803 | 0.922 | 0.773 |
| 2 | 0.859 | 0.816 | 1.031 | 0.952 | 1.096 | 0.958 |
| 3 | 0.943 | 0.914 | 1.182 | 1.126 | 1.336 | 1.221 |
| 5 | 1.014 | 0.996 | 1.317 | 1.281 | 1.596 | 1.515 |
| 10 | 1.068 | 1.059 | 1.423 | 1.405 | 1.837 | 1.793 |
| half-space | 1.122 | 1.122 | 1.532 | 1.532 | 2.105 | 2.105 |
Half-space: computed with H/B = 106. The corner factor is Is(L/B, H/B), read from Tables 1–3. Values computed by GeoTerva with the functions its elastic settlement modules use.
On deep ground the centre of a flexible square settles Ic = 1.122 and its corner 0.561, the half-space values first given by Schleicher (1926): the centre settles twice as much as the corner. A layer of finite thickness settles less, the more so the thinner it is.
A rigid footing cannot follow this dish-shaped settlement and settles uniformly. The GeoTerva modules take its settlement as 0.93 times that of the flexible centre. They apply no reduction for the depth of the foundation: the depth factor of Fox (1948), which lowers the settlement of an embedded footing, is taken as 1, on the safe side. A layered profile is handled by giving each layer its own E and ν and the difference of Is between its bottom and its top (see elastic settlement of a footing).
6Worked exampleA footing on a sand layer over rock.
A flexible footing B × L = 2.5 m × 4.0 m carries a net pressure q = 150 kPa at the ground surface. Below it lies a medium dense sand, E′ = 30 MPa and ν′ = 0.3, 7.5 m thick, on rock. The factor in front is q(1 − ν²)/E = 150 × 0.91 / 30000 = 4.550 × 10−3, and (1 − 2ν)/(1 − ν) = 0.5714.
- Centre: B′ = 1.25 m, m′ = 2.00/1.25 = 1.60, n′ = 7.5/1.25 = 6.00: F1 = 0.5337, F2 = 0.0405, Is = 0.5337 + 0.5714 × 0.0405 = 0.5568. S = 4 × 1.25 × 4.550 × 10−3 × 0.5568 = 12.7 mm.
- Corner: B′ = 2.5 m, m′ = 1.60, n′ = 3.00: F1 = 0.3955, F2 = 0.0713, Is = 0.4363. S = 2.5 × 4.550 × 10−3 × 0.4363 = 5.0 mm.
- Rigid footing: 0.93 × 12.67 = 11.8 mm.
The flexible footing would settle 7.7 mm more at its centre than at its corners. The elastic settlement module gives the same three values for this footing, with the bottom of the profile as the calculation depth. Had the layer been a saturated clay loaded undrained with the same modulus, Eu = 30 MPa and ν = 0.5, the centre would take Is = F1 = 0.5337 and the factor 1 − ν² = 0.75: S = 10.0 mm.
7QuestionsShort answers.
What are F1 and F2?
Two dimensionless functions of m′ = L′/B′ and n′ = H/B′ in the closed-form solution of Steinbrenner (1934) for the settlement of the corner of a uniformly loaded flexible rectangle on an elastic layer of thickness H over a rigid base. They combine into Is = F1 + (1 − 2ν)/(1 − ν)·F2, and S = qB′(1 − ν²)Is/E.
Why is Is = F1 for clay?
A saturated clay loaded faster than it can drain deforms at constant volume, so ν = 0.5. The weight (1 − 2ν)/(1 − ν) of F2 is then zero, and the corner settlement becomes q·B′·0.75·F1/Eu.
How is the settlement at the centre of a footing found?
Divide the footing into four rectangles B/2 × L/2 meeting at the centre and add their corner settlements: S = 4q(B/2)(1 − ν²)Is(L/B, 2H/B)/E. On deep ground the centre of a flexible square settles 1.122·qB(1 − ν²)/E, twice its corner.