1The pressures in undrained clayφ = 0: Ka = Kp = 1.
A sheet pile driven into saturated clay is loaded far faster than the clay can drain, so the wall is first designed in total stress with the undrained shear strength cu and φ = 0. The retained soil above the dredge line is taken as granular (sand or a granular fill), with its own Rankine Ka (see earth pressure coefficients); P1 is the area of its active pressure diagram per metre of wall and z̄1 the height of its centroid above the dredge line.
Below the dredge line both faces are clay, with Ka = Kp = 1. At a depth z below the dredge line the retained face carries the active pressure and the excavation face the passive pressure:
The unit weight of the clay cancels in the difference (and so does the water pressure, when the water stands at the same level on both faces), so the net pressure is constant with depth and acts towards the retained side:
Near the toe the wall moves the other way, and the net pressure reverses to σ7 = 4cu + (γL1 + γ′L2). The wall can stand only while σ6 > 0, that is while γL1 + γ′L2 < 4cu: a softer clay is squeezed from under the retained soil whatever the embedment, and the base of the excavation is close to heaving (see bottom heave in clay).
2The depth of embedmentA quadratic in D.
Let the reversal start a height L4 above the toe. No net horizontal force on the wall gives
and no net moment about the toe, with L4 substituted, a quadratic in the depth D below the dredge line:
Its positive root is the theoretical depth:
With no water table, γL1 + γ′L2 is simply γL. With the water at different levels on the two faces, the GeoTerva module replaces it by the difference of the total vertical stresses on the two faces at the dredge line and adds the net water pressure to P1.
3The maximum bending momentZero shear inside the constant block.
Below the dredge line the constant net pressure σ6 takes away the shear P1 at the rate σ6 per metre, so the shear is zero at
below the dredge line (as long as z′ lies above the reversal), and the moment there is the largest:
For a strong clay σ6 is large, z′ is short and Mmax approaches P1z̄1, the moment of the retained soil about the dredge line. As 4cu falls towards γL1 + γ′L2, both the depth and the moment grow without limit.
4The design depth and the long termD increased by 40 to 60 %.
At Dtheory the undrained strength is fully mobilised. For walls penetrating clay the depth is increased by 40 to 60 %: Ddesign = f Dtheory with f = 1.4–1.6 (the GeoTerva module proposes f = 1.5). The moment is that of the theoretical diagram. The alternative is to divide the passive pressure σv + 2cu by a factor of safety before solving.
The undrained analysis describes the wall when it is built. With time the clay drains, its strength is governed by c′ and φ′, and the net pressure below the dredge line can fall: a permanent wall in clay is checked in the long term with drained parameters as well. The GeoTerva anchored sheet-pile module runs both scenarios on a profile of sand and clay layers.
5Table of the depth and the momentDry granular soil retained over clay.
| cu/(γL) | σ6/(γL) | Dtheory/L, φ′ = 30° | Ddesign/L, f = 1.5 | Mmax/(γL³), φ′ = 30° | Dtheory/L, φ′ = 35° | Ddesign/L, f = 1.5 | Mmax/(γL³), φ′ = 35° |
|---|---|---|---|---|---|---|---|
| 0.28 | 0.12 | 3.142 | 4.71 | 0.1713 | 2.607 | 3.91 | 0.1217 |
| 0.30 | 0.20 | 2.019 | 3.03 | 0.1250 | 1.690 | 2.53 | 0.0911 |
| 0.35 | 0.40 | 1.163 | 1.75 | 0.0903 | 0.987 | 1.48 | 0.0681 |
| 0.40 | 0.60 | 0.869 | 1.30 | 0.0787 | 0.744 | 1.12 | 0.0605 |
| 0.45 | 0.80 | 0.717 | 1.08 | 0.0729 | 0.618 | 0.93 | 0.0566 |
| 0.50 | 1.00 | 0.623 | 0.93 | 0.0694 | 0.539 | 0.81 | 0.0543 |
| 0.60 | 1.40 | 0.510 | 0.77 | 0.0655 | 0.445 | 0.67 | 0.0517 |
| 0.70 | 1.80 | 0.443 | 0.67 | 0.0633 | 0.388 | 0.58 | 0.0503 |
| 0.80 | 2.20 | 0.398 | 0.60 | 0.0619 | 0.349 | 0.52 | 0.0493 |
| 1.00 | 3.00 | 0.339 | 0.51 | 0.0602 | 0.299 | 0.45 | 0.0482 |
| 1.25 | 4.00 | 0.293 | 0.44 | 0.0590 | 0.259 | 0.39 | 0.0475 |
| 1.50 | 5.00 | 0.262 | 0.39 | 0.0583 | 0.233 | 0.35 | 0.0470 |
| 2.00 | 7.00 | 0.222 | 0.33 | 0.0575 | 0.198 | 0.30 | 0.0465 |
No water, no surcharge; σ6 = 4cu − γL. Below cu/(γL) = 0.25 there is no solution. Multiply by L (m) for the depths and by γL³ (kN·m per metre of wall) for the moment. Values computed by GeoTerva with the function its sheet-pile module uses.
The table shows how sharply the depth depends on the strength near the limit: for φ′ = 30°, Dtheory is 0.62 L at cu = 0.5γL but 2.02 L at cu = 0.3γL. A clay that is only just strong enough does not make a practical cantilever wall: an anchor, or a deeper and stiffer wall checked against heave, is needed.
6Worked exampleSand retained over a clay, cu = 40 kPa.
A cantilever wall retains L = 5.0 m of sand (φ′ = 30°, γ = 17.5 kN/m³, γsat = 19.5 kN/m³) and is driven into a clay with cu = 40 kPa. The water stands 2.0 m below the top on both faces: L1 = 2.0 m, L2 = 3.0 m, γ′ = 9.69 kN/m³.
- Active pressure of the sand: Ka = 0.3333; σ′1 = 17.5 × 2.0 × 0.3333 = 11.67 kPa at the water table, σ′2 = 21.36 kPa at the dredge line.
| Block | Shape and depth | Area (kN/m) | Arm above the dredge line (m) | Moment (kN·m/m) |
|---|---|---|---|---|
| 1 | triangle, 0.0–2.0 m | 11.67 | 3.667 | 42.78 |
| 2 | rectangle, 2.0–5.0 m | 35.00 | 1.500 | 52.50 |
| 3 | triangle, 2.0–5.0 m | 14.54 | 1.000 | 14.54 |
| Σ | 61.20 | 1.794 | 109.81 |
Depths from the top of the wall. z̄1 = Σ(area × arm)/P1. Values computed by GeoTerva.
- Net pressure in the clay: γL1 + γ′L2 = 17.5 × 2.0 + 9.69 × 3.0 = 64.07 kPa (less than 4cu = 160 kPa), so σ6 = 160 − 64.07 = 95.93 kPa and σ7 = 224.07 kPa.
- Quadratic: 95.93 D² − 122.40 D − 391.86 = 0, with C = 61.20 × (61.20 + 12 × 40 × 1.794) / (64.07 + 2 × 40) = 391.86, so Dtheory = 2.76 m; L4 = (95.93 × 2.757 − 61.20) / (4 × 40) = 1.271 m.
- Design depth: Ddesign = 1.5 × 2.76 = 4.14 m, a sheet pile 9.14 m long.
- Maximum moment: z′ = 61.20 / 95.93 = 0.638 m below the dredge line; Mmax = 61.20 × (0.638 + 1.794) − 95.93 × 0.638² / 2 = 129.3 kN·m/m.
The shear and the moment come back to zero at the toe. Driven into the same sand as it retains, the wall would need Dtheory = 6.19 m and carry Mmax = 273.9 kN·m/m (see cantilever sheet pile in sand): in the short term the clay resists with its full strength from the dredge line down, whereas the passive resistance of a sand builds up from zero. The sheet pile in clay module of GeoTerva also handles retained clay with its tension crack, water at different levels, anchors, the seismic situation and the displacement.
7QuestionsShort answers.
What is the net pressure below the dredge line in clay?
σ6 = 4cu − (γL1 + γ′L2), constant with depth: the passive pressure γsatz + 2cu in front of the wall less the active pressure (γL1 + γ′L2) + γsatz − 2cu behind it, the weight of the clay cancelling.
When can a cantilever wall not be built in clay?
When γL1 + γ′L2 ≥ 4cu: σ6 is then zero or negative, the clay in front of the wall cannot hold it at any depth, and the quadratic has no positive root. For dry retained soil this is cu/(γL) ≤ 0.25.
How much is the theoretical depth increased in clay?
By 40 to 60 %, Ddesign = 1.4–1.6 Dtheory, more than the 20–30 % used in sand, because the undrained strength is uncertain and the long-term drained strength can be lower.