1Two parts of the settlementWhat happens at once, and what takes time.
The total settlement of a shallow foundation is the sum of two parts that differ in their cause and in their timing:
- The immediate settlement Se occurs as the load is applied. In a saturated clay, which cannot drain that fast, it is a distortion at constant volume (undrained, Eu, ν = 0.5); in a sand or gravel, which drains at once, it is the whole settlement (drained, E′, ν′).
- The consolidation settlement Sc is the volume decrease of the clay layers as the excess pore water drains away. It takes months to decades, at a rate set by the coefficient of consolidation and the drainage path (Terzaghi, 1925).
A sand layer therefore contributes Se only, a clay layer Se and Sc. The GeoTerva total settlement module computes the two on the same slices of one profile, with the same Boussinesq stress increase, the same excavation and the same calculation depth, and adds them. Sc is the primary consolidation; the slow secondary compression that may follow it at constant effective stress (Buisman, 1936) is a separate term with its own index.
2The immediate partSteinbrenner’s factors, layer by layer.
Each layer between the depths zt and zb below the foundation level contributes, with its own modulus and Poisson’s ratio,
with the influence factor Is of Steinbrenner (1934), α = 4 and B′ = B/2 at the centre, α = 1 and B′ = B at a corner, and the net pressure qnet = q − σ′v0(D). A clay layer takes Eu and ν = 0.5, a sand layer E′ and ν′. The factors are tabulated on Steinbrenner influence factors, and the moduli, the net pressure and the calculation depth are discussed on elastic settlement of a footing.
3The consolidation partThe e–log σ′ formulas along the stress path.
Each slice of a clay layer, of thickness H and initial void ratio e0, compresses from its effective stress σ′0 to σ′f, with the recompression index Cr up to its preconsolidation pressure σ′p = OCR·σ′0 and the compression index Cc beyond:
If σ′f ≤ σ′p only the first term remains, with σ′f in place of σ′p; for a normally consolidated clay σ′p = σ′0 and only the second remains. Where the foundation sits in an excavation, the clay first swells and then recovers the swelling before it is compressed; measured from the original ground the consolidation settlement is Sc + Sheave. The formulas, a table for one metre of clay and the stress path are on consolidation settlement of clay. With time, each clay layer i follows Terzaghi’s degree of consolidation Ui (see time factor):
4Worked exampleA footing over sand and clay layers.
A footing B × L = 8 m × 12 m is founded at D = 1.5 m and carries a gross pressure of 140 kPa; the water table is at 2.0 m. Below the sandy fill that is dug out:
- 1.5–4.5 m medium dense sand: E′ = 25 MPa, ν′ = 0.3;
- 4.5–10 m soft to firm clay: Eu = 12 MPa, γsat = 18 kN/m³, e0 = 1.00, Cc = 0.32, Cr = Cs = 0.05, OCR = 1.4, cv = 1.2 m²/year;
- 10–16 m dense sand: E′ = 50 MPa, ν′ = 0.3;
- 16–30 m stiff clay: Eu = 45 MPa, e0 = 0.70, Cc = 0.18, Cr = 0.03, OCR = 2.5, cv = 3 m²/year.
The excavation removes 27.0 kPa, so qnet = 113.0 kPa, and the influence depth (10 %) lies at 21.87 m: the stiff clay is counted down to it. Two lines of the hand calculation at the centre (α = 4, B′ = 4 m, m′ = 1.50):
- Sand, Se: z′ = 0–3.00 m, Is(1.50, 0.750, ν = 0.3) = 0.1397: 113.0 × 0.91 / 25000 × 4 × 4 × 0.1397 = 9.2 mm.
- Clay, Se: z′ = 3.00–8.50 m, Is = F1 = 0.0853 to 0.3079: 113.0 × 0.75 / 12000 × 4 × 4 × (0.3079 − 0.0853) = 25.2 mm.
- Clay, Sc: every slice passes σ′p (Cr, then Cc): 143.2 mm of compression from the excavation base, of which 14.6 mm recovers the swelling of the excavation, so 128.6 mm from the original ground. The stiff clay stays below its σ′p and adds 3.4 mm.
| Layer | Type | Depth compressed (m) | Se | Se corner | Heave | Sc from the excavation base | Sc + Sheave | Total |
|---|---|---|---|---|---|---|---|---|
| Medium dense sand | sand | 1.50–4.50 | 9.2 | 2.1 | — | — | — | 9.2 |
| Soft to firm clay | clay | 4.50–10.00 | 25.2 | 6.7 | −14.6 | 143.2 | 128.6 | 153.7 |
| Dense sand | sand | 10.00–16.00 | 3.7 | 1.9 | — | — | — | 3.7 |
| Stiff clay | clay | 16.00–21.87 | 1.9 | 1.3 | −0.9 | 4.2 | 3.4 | 5.3 |
| Total | 40.0 | 12.0 | −15.5 | 147.4 | 132.0 | 172.0 |
Total = Se + Sc + Sheave, measured from the original ground. Values computed by GeoTerva with the engine of its total settlement module.
The footing settles 172.0 mm at its centre, 144.0 mm at a corner and 169.2 mm as a rigid footing. The immediate part is 40.0 mm (23 %), the consolidation of the clay 132.0 mm (77 %); the soft-to-firm clay alone gives 89 % of the total. With time:
| t (years) | Consolidation U (%) | S (mm) |
|---|---|---|
| 0 (end of loading) | 0 | 24.5 |
| 0.5 | 31 | 70.9 |
| 1 | 44 | 90.0 |
| 2 | 62 | 116.3 |
| 5 | 88 | 153.9 |
| 10 | 98 | 168.9 |
| 20 | 100 | 171.7 |
At the end of loading the footing has settled Se = 40.0 mm into ground that had heaved 15.5 mm during the excavation. Values computed by GeoTerva.
Half of the consolidation is reached after 1.3 years and 90 % after 5.5 years. One year after loading the footing has settled 90.0 mm; the remaining 81.9 mm come afterwards.
5Which part governsAgainst the stress history and the load.
Whether the immediate or the consolidation part is the larger depends above all on whether the clay is loaded past its preconsolidation pressure. Table 3 repeats the worked example with other overconsolidation ratios for the soft-to-firm clay, all else unchanged:
| OCR | Se | Sc + Sheave | Total | Share of consolidation |
|---|---|---|---|---|
| 1 | 40.0 | 240.5 | 280.5 | 86 % |
| 1.2 | 40.0 | 181.7 | 221.7 | 82 % |
| 1.4 | 40.0 | 132.0 | 172.0 | 77 % |
| 1.7 | 40.0 | 81.0 | 120.9 | 67 % |
| 2 | 40.0 | 55.8 | 95.7 | 58 % |
| 2.5 | 40.0 | 40.8 | 80.8 | 51 % |
| 3 | 40.0 | 40.4 | 80.4 | 50 % |
Se is the same in every row because Eu is entered directly; a real clay with a higher OCR is usually stiffer as well. Values computed by GeoTerva.
Normally consolidated, the clay gives 240.5 mm of consolidation against 40.0 mm of immediate settlement; with OCR = 3 it stays below σ′p and the consolidation, 40.4 mm, is about the size of the immediate part. The pressure acts the same way (Table 4): the immediate settlement grows in proportion to qnet, the consolidation faster once σ′p is passed.
| q (kPa) | qnet (kPa) | Se | Sc + Sheave | Total | Share of consolidation |
|---|---|---|---|---|---|
| 60 | 33 | 11.7 | 15.6 | 27.3 | 57 % |
| 80 | 53 | 18.7 | 38.6 | 57.3 | 67 % |
| 100 | 73 | 25.8 | 68.2 | 94.0 | 73 % |
| 140 | 113 | 40.0 | 132.0 | 172.0 | 77 % |
| 180 | 153 | 54.1 | 189.9 | 244.0 | 78 % |
| 220 | 193 | 68.3 | 240.2 | 308.5 | 78 % |
Values computed by GeoTerva with the engine of its total settlement module.
From q = 60 to 220 kPa the immediate part rises from 11.7 to 68.3 mm and the consolidation from 15.6 to 240.2 mm. In short: on sand and gravel the immediate settlement is the whole settlement; on a normally or lightly overconsolidated clay loaded past σ′p the consolidation governs and is usually several times the immediate part; on a clay that stays below σ′p the two are of the same order, and both must be added.
6QuestionsShort answers.
Are the immediate and the consolidation settlement simply added?
Yes: the GeoTerva total settlement module gives S = Se + Sc, the undrained settlement and the one-dimensional consolidation. Skempton and Bjerrum (1957) showed that under a footing of limited size the consolidation part depends on the pore-pressure response of the clay, and that for overconsolidated clays the one-dimensional value overstates it.
Does a sand layer have a consolidation settlement?
No. A sand or gravel drains as fast as it is loaded, so its whole settlement is the drained, immediate one, computed with E′ and ν′. Only clay and silt layers add a consolidation settlement.
Which part of the settlement happens first?
The immediate settlement occurs as the load is applied, mostly during construction. The consolidation follows over months or years: in the worked example half of it after 1.3 years and 90 % after 5.5 years.