GeoTerva Open the module

Formulas and tables · Laterally loaded piles

p–y curves for sand and clay: API sand and Matlock soft clay

The non-linear springs of a laterally loaded pile: the API curve of a sand after Reese, Cox and Koop, the soft-clay curve of Matlock, their ultimate resistances, and the curves at one depth, static and cyclic.

  • Free to read
  • Sand · soft clay
  • Static and cyclic
  • Worked example

1What a p–y curve isThe reaction of the ground against the deflection of the pile.

A pile under a lateral load is a beam held by the ground along its length. In the p–y method the ground is a row of independent springs, and each spring follows a curve of the soil reaction p (force per unit length of the pile, kN/m) against the deflection y of the pile at that depth. The beam equation becomes

EId4ydz4+Pd2ydz2+p(y,z)=0

EI is the bending stiffness of the pile and P its axial load. A p–y curve starts steep, softens as the soil yields and ends on the ultimate resistance pu of the soil at that depth, which grows with depth and with the strength of the soil. The equation is solved numerically, depth by depth along the pile; the curves below are the ones the GeoTerva laterally loaded pile module uses.

2Sand: the API curveReese, Cox and Koop (1974), as API RP 2A states it.

Reese, Cox and Koop (1974) built the curve of a sand from field tests and from two mechanisms of failure: a wedge pushed up in front of the pile near the surface, and the soil flowing round the pile deeper down. The ultimate resistance is the smaller of the two:

pu=min[(C1z+C2D)σ′v,C3Dσ′v]

with σ′v the effective vertical stress at the depth z, D the width of the pile and coefficients that depend on φ′ alone:

C1=K0tan⁡φ′sin⁡βtan⁡(β−φ′)cos⁡α+tan2βtan⁡αtan⁡(β−φ′)+K0tan⁡β(tan⁡φ′sin⁡β−tan⁡α)
C2=tan⁡βtan⁡(β−φ′)−Ka,C3=K0tan⁡φ′tan4β+Ka(tan8β−1)

where α = φ′/2, β = 45° + φ′/2, K0 = 0.4 and Ka = tan²(45° − φ′/2). API RP 2A writes the curve in the hyperbolic-tangent form of O’Neill and Murchison (1983):

p=Aputanh⁡(kzyApu),A=max(3.0−0.8zD,0.9)

for static loading; for cyclic loading A = 0.9 at every depth. k is the initial modulus of subgrade reaction (kN/m³), read from the API chart against φ′, with a lower value below the water table. At small deflections the curve is the straight line p = kzy, the elastic subgrade reaction with nh = k; at large deflections it ends on Apu.

Table 1. Coefficients of the ultimate resistance and the initial modulus k of the sand curve
φ′C1C2C3k above the water table (MN/m³)k below the water table (MN/m³)
28°1.602.4122.525.45.4
29°1.752.5425.436.06.4
30°1.912.6728.7510.57.9
31°2.092.8032.5115.49.7
32°2.282.9536.8120.711.9
33°2.493.1041.7326.514.6
34°2.723.2547.3532.717.6
35°2.973.4253.7939.321.0
36°3.243.5961.2046.324.8
37°3.543.7769.7353.829.0
38°3.873.9779.5761.733.6
39°4.234.1790.9570.138.6
40°4.624.38104.1578.944.0

k: a quadratic fitted to the API chart, not less than 5.4 MN/m³, as the GeoTerva module fills it in (it can be typed over there). Values computed by GeoTerva with the functions its laterally loaded pile module uses.

3Soft clay: Matlock (1970)A cube-root curve, static and cyclic.

Matlock (1970) derived the curve of a soft clay from tests on instrumented piles. The ultimate resistance at the depth z, with cu the undrained shear strength, is again the smaller of a shallow (wedge) and a deep (flow-around) value:

pu=min[(3+σ′vcu+JzD)cuD,9cuD]

and the static curve is a cube root up to eight times y50, the deflection at which half of pu is mobilised:

ppu=0.5(yy50)1/3(y≤8y50),y50=2.5ε50D

with p = pu beyond 8y50. ε50 is the strain at half the maximum deviator stress in an undrained triaxial test; when none is measured, the GeoTerva module fills in 0.020 for a soft clay (cu below 48 kPa), 0.010 for a medium one and 0.005 for a stiff one (96 kPa and more). J is 0.50 for a soft clay and 0.25 for a medium to stiff one.

Cyclic loading. Up to 3y50 the curve is the static one, which has reached 0.72pu there. Below the transition depth zR the resistance then stays at 0.72pu; above it, it falls linearly to 0.72pu·z/zR at 15y50 and stays there:

zR=6Dγ′Dcu+J

γ′ being the effective unit weight of the clay above z (the GeoTerva module keeps zR not less than 2.5D).

4Tables of p against yA sand and a soft clay at one depth, static and cyclic.

Table 2. The API sand curve at z = 1.20 m: φ′ = 35°, γ = 18 kN/m³ (dry), D = 0.60 m
y (mm)p static (kN/m)p/pu staticp cyclic (kN/m)
0.523.40.19323.2
1.046.00.37944.4
2.085.60.70676.2
3.0115.80.95593.9
5.0149.91.236106.3
7.5164.61.357108.8
10.0168.51.389109.1
15.0169.71.399109.2
20.0169.81.400109.2
30.0169.81.400109.2
50.0169.81.400109.2

pu = 121.3 kN/m, A = 1.40 (static) and 0.90 (cyclic), k = 39.3 MN/m³: the static curve ends on 169.8 kN/m, the cyclic one on 109.2 kN/m. Values computed by GeoTerva with the function its module uses.

Table 3. Matlock’s soft-clay curve at z = 3.0 m: cu = 30 kPa, γsat = 17 kN/m³, water table at the ground, D = 0.60 m
y/y50y (mm)p static (kN/m)p/pu staticp cyclic (kN/m)
0.13.026.00.23226.0
0.257.535.30.31535.3
0.515.044.40.39744.4
130.056.00.50056.0
260.070.50.63070.5
390.080.70.72180.7
5150.095.70.85574.5
8240.0111.91.00065.1
10300.0111.91.00058.9
15450.0111.91.00043.3
20600.0111.91.00043.3

pu = 111.9 kN/m, y50 = 30.0 mm (ε50 = 0.020), zR = 5.59 m: at this depth, above zR, the cyclic curve falls to 43.3 kN/m. Values computed by GeoTerva with the function its module uses.

5Worked exampleThe two curves at one depth, by hand.

Sand. A pile D = 0.60 m wide in a dry sand with φ′ = 35° and γ = 18 kN/m³, at z = 1.20 m: σ′v = 18 × 1.20 = 21.6 kPa. Table 1 gives C1 = 2.97, C2 = 3.42, C3 = 53.79, so

  • (C1z + C2D)σ′v = (2.97 × 1.20 + 3.42 × 0.60) × 21.6 = 121.3 kN/m and C3Dσ′v = 53.79 × 0.60 × 21.6 = 697.2 kN/m: pu = 121.3 kN/m (the wedge value governs).
  • A = 3.0 − 0.8 × 1.20/0.60 = 1.40, k = 39.3 MN/m³ (above the water table). At y = 10 mm: kzy/(Apu) = 39.3×10³ × 1.20 × 0.010 / (1.40 × 121.3) = 2.775, and p = 1.40 × 121.3 × tanh(2.775) = 168.5 kN/m.

Soft clay. The same pile in a clay with cu = 30 kPa and γsat = 17 kN/m³ below the water table, at z = 3.0 m: σ′v = (17 − 9.81) × 3.0 = 21.57 kPa, ε50 = 0.020, J = 0.50.

  • (3 + 21.57/30 + 0.50 × 3.0/0.60) × 30 × 0.60 = 111.9 kN/m against 9 × 30 × 0.60 = 162.0 kN/m: pu = 111.9 kN/m.
  • y50 = 2.5 × 0.020 × 0.60 = 30.0 mm. At y = y50, p = 0.5pu = 56.0 kN/m; at 8y50 = 240 mm the static curve reaches pu = 111.9 kN/m, while under cyclic loading the clay at this depth (z/zR = 0.54) is down to 43.3 kN/m at 15y50.

The module integrates curves like these along the whole pile and solves the beam equation for the deflection, the bending moment and the shear. In a group, the curve of each row is scaled by its p-multiplier; the vertical loads of the same piles come from the cap (see the load on each pile of a group).

6QuestionsShort answers.

What is the factor A in the API sand curve?

A raises the end of the curve near the surface under static loading: A = 3.0 − 0.8z/D, not less than 0.9, which it reaches at z = 2.625D. Under cyclic loading A = 0.9 at every depth, so the cyclic curve of a sand differs from the static one only in the top few diameters.

Can Matlock’s curve be used for a stiff clay?

It was derived for soft clay. Stiff clays have curves of their own (Reese and Welch, 1975, above the water table; Reese, Cox and Koop, 1975, below it). With the ε50 of a stiff clay entered and J = 0.25 the Matlock curve is a substitute, and its results should be judged as those of a curve not calibrated on such a clay.

How are p–y curves changed for a pile in a group?

Each curve is multiplied by a p-multiplier Pm ≤ 1 that depends on the row of the pile and on the spacing: the leading row keeps most of its resistance, the rows behind it less (Brown, Morrison and Reese, 1988; Rollins et al., 2006). The GeoTerva pile group module applies them layer by layer.

The theory behind it