1The λ methodVijayvergiya and Focht (1972).
Vijayvergiya and Focht (1972) fitted a single expression to load tests on long steel pipe piles driven into clay, most of them for offshore structures. They took the soil displaced by driving to exert a passive lateral pressure on the shaft, and wrote the average unit skin friction over the whole embedded length as
where σ̄′v is the mean vertical effective stress over the embedded length, c̄u the mean undrained shear strength, and λ a coefficient that depends only on the embedded length L. The term σ′v + 2cu is the passive pressure of a clay in the undrained state; λ scales it to the friction the load tests measured. The shaft resistance is then
with p the perimeter of the pile. Unlike the α method, the λ method uses the effective stress as well as the strength, so the unit weights and the water table enter it.
2The two means in a layered clayWeighted by thickness and by area.
In a layered clay the mean strength is weighted by the thickness of each layer, and the mean effective stress is the area of the effective-stress diagram divided by the embedded length:
Ai is the area under the σ′v–depth line over layer i. σ′v grows linearly within a layer and changes slope at every layer boundary and at the water table, so each area is a set of trapezoids broken at those depths.
λ is read once, at the length of the pile, and applied to the whole shaft: the method was fitted to whole piles, not to layers. Applying it layer by layer with the λ of the full length is an extension of the method, not part of it.
3Table of λEmbedded length 0–90 m.
| L (m) | λ |
|---|---|
| 0 | 0.500 |
| 5 | 0.336 |
| 10 | 0.245 |
| 15 | 0.200 |
| 20 | 0.173 |
| 25 | 0.150 |
| 30 | 0.136 |
| 35 | 0.132 |
| 40 | 0.127 |
| 45 | 0.122 |
| 50 | 0.118 |
| 55 | 0.115 |
| 60 | 0.113 |
| 65 | 0.112 |
| 70 | 0.110 |
| 75 | 0.110 |
| 80 | 0.110 |
| 85 | 0.110 |
| 90 | 0.110 |
After Vijayvergiya and Focht (1972), read by straight-line interpolation between the tabulated lengths; λ stays at 0.110 beyond 70 m. Values computed by GeoTerva with the functions its pile modules use.
Because λ falls with length while σ̄′v grows, the average friction changes much less with length than either term does. Table 2 shows this for a uniform clay with cu = 50 kPa, γsat = 18 kN/m³ and the water table at the ground surface, beside the α method on the same pile (D = 0.6 m).
| L (m) | σ̄′v (kPa) | λ | fav, λ method (kPa) | Qs, λ method (kN) | f, α method (kPa) | Qs, α method (kN) |
|---|---|---|---|---|---|---|
| 5 | 20.5 | 0.336 | 40.5 | 382 | 34.0 | 320 |
| 10 | 41.0 | 0.245 | 34.5 | 651 | 34.0 | 641 |
| 15 | 61.4 | 0.200 | 32.3 | 913 | 34.0 | 961 |
| 20 | 81.9 | 0.173 | 31.5 | 1186 | 34.0 | 1282 |
| 25 | 102.4 | 0.150 | 30.4 | 1431 | 34.0 | 1602 |
| 30 | 122.8 | 0.136 | 30.3 | 1714 | 34.0 | 1923 |
| 40 | 163.8 | 0.127 | 33.5 | 2526 | 34.0 | 2564 |
| 50 | 204.7 | 0.118 | 36.0 | 3389 | 34.0 | 3204 |
| 60 | 245.7 | 0.113 | 39.1 | 4418 | 34.0 | 3845 |
γw = 9.81 kN/m³. Values computed by GeoTerva with the functions its pile modules use.
4Worked exampleA 24 m pipe pile through three clays.
A steel pipe pile D = 0.5 m is driven L = 24 m into three clays, with the water table at 2 m: 0–5 m, cu = 35 kPa, γ = 17.5 kN/m³; 5–14 m, cu = 55 kPa, γsat = 18 kN/m³; 14–24 m, cu = 85 kPa, γsat = 19 kN/m³ (γw = 9.81 kN/m³).
- Mean strength: c̄u = (35 × 5 + 55 × 9 + 85 × 10)/24 = 63.33 kPa.
- Mean effective stress: σ′v = 35.0 kPa at 2 m, 58.1 kPa at 5 m, 131.8 kPa at 14 m and 223.7 kPa at 24 m. The areas of the diagram over the three layers are A1 = 174.6, A2 = 854.3 and A3 = 1777.3 kN/m, so σ̄′v = (174.6 + 854.3 + 1777.3)/24 = 116.93 kPa.
- λ at L = 24 m: between λ = 0.173 at 20 m and 0.150 at 25 m, λ = 0.1546.
- Average friction: fav = 0.1546 × (116.93 + 2 × 63.33) = 37.66 kPa.
- Shaft resistance: Qs = πDLfav = π × 0.5 × 24 × 37.66 = 1420 kN.
The α method on the same pile, layer by layer, gives 1421 kN, almost the same. The agreement belongs to this profile rather than to the methods, which share only the strengths: on a longer pile or in a different clay they drift apart, as Table 2 shows. The point resistance is added separately (see pile end bearing in clay).
5QuestionsShort answers.
What does λ depend on?
Only on the embedded length of the pile: λ = 0.500 at the surface, 0.173 at 20 m and 0.110 beyond 70 m. The soil enters through σ̄′v and c̄u, not through λ.
Can the λ method be used for a bored pile?
It was fitted to piles driven into clay, where driving displaces the soil and raises the lateral pressure on the shaft; a bored pile displaces nothing. The GeoTerva pile modules therefore refuse the λ method for a bored pile and offer the α method with the drilled-shaft rule instead.
Why is λ applied to the whole pile and not to each layer?
Vijayvergiya and Focht fitted λ to the total shaft resistance of whole piles, with the means of σ′v and cu over the full length. The friction it gives is an average for the pile, not the friction at any one depth.