1What K0 isLateral stress without lateral strain.
A soil element that has been loaded or unloaded only vertically, with no lateral strain, carries a horizontal effective stress that is a fixed fraction of the vertical one. That fraction is the coefficient of earth pressure at rest:
A wall that cannot move keeps the soil behind it in this state: a basement wall propped by its floors, a box culvert, a bridge abutment on a stiff pile group, the wall of a tank. The pressure grows linearly with depth in a uniform dry soil, and the thrust per metre of wall acts at H/3 above the base:
K0 lies between the active and the passive coefficients, Ka < K0 < Kp (see earth pressure coefficients). It is also the starting point of other calculations: the horizontal stress on a pile shaft, the initial stress state of a numerical model, the stress path of a laboratory test.
2Normally consolidated soilsJaky, Massarsch, Sherif.
For a normally consolidated sand, and approximately for a normally consolidated clay in terms of its drained friction angle, the relationship of Jaky (1944), in the simplified form used in practice, is
For normally consolidated clays Massarsch (1979) related K0 to the plasticity index PI:
A compacted fill is not normally consolidated: rolling it locks horizontal stress in. For a sand compacted behind a non-yielding wall, Sherif, Fang and Sherif (1984) proposed
with γd the compacted dry unit weight and γd,min the dry unit weight of the sand in its loosest state. The second term is large: a fill only 4 % denser than its loosest state adds 0.220 to K0.
3Overconsolidated soilsMayne and Kulhawy (1982).
When a soil is unloaded — by erosion, by the melting of an ice sheet, by excavation — the vertical stress falls but much of the horizontal stress stays. K0 then grows with the overconsolidation ratio, OCR = σ′p/σ′v, the ratio of the preconsolidation pressure to the present vertical effective stress. Mayne and Kulhawy (1982), from laboratory data on 171 soils from clay to gravel, extended Jaky’s relationship to
The relationship describes a soil on its first unloading; reloading it, for example by placing a fill on an eroded surface, brings K0 back toward the normally consolidated value. K0 exceeds 1 in heavily overconsolidated soil: for φ′ = 30° at OCR = 4.00, for φ′ = 35° at OCR = 4.42. It cannot exceed the passive coefficient, at which the soil fails in horizontal compression:
With the Mayne and Kulhawy relationship that limit is reached at OCR = 36 for φ′ = 30° and OCR = 53 for φ′ = 40°, which in practice happens only near the ground surface of a heavily overconsolidated deposit.
For overconsolidated clays the value of Massarsch is commonly multiplied by √OCR; this correction is an approximation used in practice and is not part of Massarsch’s relationship:
4Table of K0 against φ′ and OCRMayne and Kulhawy, every degree.
| φ′ | OCR = 1 | OCR = 1.5 | OCR = 2 | OCR = 3 | OCR = 4 | OCR = 6 | OCR = 8 | OCR = 10 |
|---|---|---|---|---|---|---|---|---|
| 20° | 0.658 | 0.756 | 0.834 | 0.958 | 1.057 | 1.214 | 1.340 | 1.446 |
| 21° | 0.642 | 0.742 | 0.823 | 0.951 | 1.054 | 1.219 | 1.352 | 1.464 |
| 22° | 0.625 | 0.728 | 0.811 | 0.944 | 1.051 | 1.224 | 1.363 | 1.482 |
| 23° | 0.609 | 0.714 | 0.799 | 0.936 | 1.047 | 1.227 | 1.373 | 1.498 |
| 24° | 0.593 | 0.700 | 0.786 | 0.927 | 1.043 | 1.230 | 1.382 | 1.514 |
| 25° | 0.577 | 0.685 | 0.774 | 0.919 | 1.037 | 1.231 | 1.390 | 1.528 |
| 26° | 0.562 | 0.671 | 0.761 | 0.909 | 1.031 | 1.232 | 1.397 | 1.541 |
| 27° | 0.546 | 0.656 | 0.748 | 0.899 | 1.025 | 1.232 | 1.403 | 1.553 |
| 28° | 0.531 | 0.642 | 0.735 | 0.889 | 1.017 | 1.230 | 1.408 | 1.564 |
| 29° | 0.515 | 0.627 | 0.721 | 0.878 | 1.009 | 1.228 | 1.412 | 1.573 |
| 30° | 0.500 | 0.612 | 0.707 | 0.866 | 1.000 | 1.225 | 1.414 | 1.581 |
| 31° | 0.485 | 0.598 | 0.693 | 0.854 | 0.990 | 1.220 | 1.415 | 1.588 |
| 32° | 0.470 | 0.583 | 0.679 | 0.841 | 0.980 | 1.215 | 1.415 | 1.593 |
| 33° | 0.455 | 0.568 | 0.664 | 0.828 | 0.969 | 1.208 | 1.413 | 1.596 |
| 34° | 0.441 | 0.553 | 0.650 | 0.815 | 0.957 | 1.201 | 1.410 | 1.598 |
| 35° | 0.426 | 0.538 | 0.635 | 0.801 | 0.944 | 1.192 | 1.406 | 1.597 |
| 36° | 0.412 | 0.523 | 0.620 | 0.786 | 0.931 | 1.182 | 1.399 | 1.596 |
| 37° | 0.398 | 0.508 | 0.604 | 0.771 | 0.917 | 1.171 | 1.392 | 1.592 |
| 38° | 0.384 | 0.493 | 0.589 | 0.756 | 0.902 | 1.158 | 1.383 | 1.586 |
| 39° | 0.371 | 0.478 | 0.573 | 0.740 | 0.887 | 1.145 | 1.372 | 1.579 |
| 40° | 0.357 | 0.464 | 0.558 | 0.724 | 0.871 | 1.130 | 1.360 | 1.569 |
| 41° | 0.344 | 0.449 | 0.542 | 0.707 | 0.854 | 1.114 | 1.346 | 1.558 |
| 42° | 0.331 | 0.434 | 0.526 | 0.690 | 0.837 | 1.097 | 1.330 | 1.544 |
| 43° | 0.318 | 0.419 | 0.510 | 0.673 | 0.819 | 1.079 | 1.313 | 1.529 |
| 44° | 0.305 | 0.405 | 0.494 | 0.655 | 0.800 | 1.060 | 1.295 | 1.512 |
| 45° | 0.293 | 0.390 | 0.478 | 0.637 | 0.781 | 1.040 | 1.274 | 1.492 |
Values computed by GeoTerva with the function its at-rest earth pressure module uses.
5Tables for clay and compacted sandMassarsch; Sherif, Fang and Sherif.
| PI (%) | OCR = 1 | OCR = 1.5 | OCR = 2 | OCR = 3 | OCR = 4 |
|---|---|---|---|---|---|
| 10 | 0.482 | 0.590 | 0.682 | 0.835 | 0.964 |
| 15 | 0.503 | 0.616 | 0.711 | 0.871 | 1.006 |
| 20 | 0.524 | 0.642 | 0.741 | 0.908 | 1.048 |
| 25 | 0.545 | 0.667 | 0.771 | 0.944 | 1.090 |
| 30 | 0.566 | 0.693 | 0.800 | 0.980 | 1.132 |
| 35 | 0.587 | 0.719 | 0.830 | 1.017 | 1.174 |
| 40 | 0.608 | 0.745 | 0.860 | 1.053 | 1.216 |
| 45 | 0.629 | 0.770 | 0.890 | 1.089 | 1.258 |
| 50 | 0.650 | 0.796 | 0.919 | 1.126 | 1.300 |
| 60 | 0.692 | 0.848 | 0.979 | 1.199 | 1.384 |
| 70 | 0.734 | 0.899 | 1.038 | 1.271 | 1.468 |
OCR = 1: Massarsch (1979). OCR > 1: the √OCR approximation. Values computed by GeoTerva.
| γd/γd,min | φ′ = 30° | φ′ = 32° | φ′ = 34° | φ′ = 36° | φ′ = 38° | φ′ = 40° |
|---|---|---|---|---|---|---|
| 1.00 | 0.500 | 0.470 | 0.441 | 0.412 | 0.384 | 0.357 |
| 1.01 | 0.555 | 0.525 | 0.496 | 0.467 | 0.439 | 0.412 |
| 1.02 | 0.610 | 0.580 | 0.551 | 0.522 | 0.494 | 0.467 |
| 1.04 | 0.720 | 0.690 | 0.661 | 0.632 | 0.604 | 0.577 |
| 1.06 | 0.830 | 0.800 | 0.771 | 0.742 | 0.714 | 0.687 |
| 1.08 | 0.940 | 0.910 | 0.881 | 0.852 | 0.824 | 0.797 |
| 1.10 | 1.050 | 1.020 | 0.991 | 0.962 | 0.934 | 0.907 |
γd/γd,min = 1 is the loosest state, where the relationship returns Jaky’s value. Values computed by GeoTerva.
6Worked exampleA propped wall in an overconsolidated sand.
A basement wall H = 6 m high is propped rigidly by its floors and cannot move. It retains a dry, dense sand with φ′ = 33° and γ = 18 kN/m³ that was once buried under about 5 m of soil since eroded: at every depth the preconsolidation pressure exceeds the present vertical stress by 90 kPa, σ′p = σ′v + 90 kPa. The OCR is therefore large near the surface and falls with depth. Neglecting the disturbance caused by building the wall, the soil keeps its in-situ K0:
| z (m) | σ′v (kPa) | σ′p (kPa) | OCR | K0 | σ′h (kPa) | σ′h if normally consolidated (kPa) |
|---|---|---|---|---|---|---|
| 0.5 | 9.0 | 99.0 | 11.00 | 1.681 | 15.1 | 4.1 |
| 1.0 | 18.0 | 108.0 | 6.00 | 1.208 | 21.7 | 8.2 |
| 2.0 | 36.0 | 126.0 | 3.50 | 0.901 | 32.4 | 16.4 |
| 3.0 | 54.0 | 144.0 | 2.67 | 0.777 | 42.0 | 24.6 |
| 4.0 | 72.0 | 162.0 | 2.25 | 0.708 | 51.0 | 32.8 |
| 5.0 | 90.0 | 180.0 | 2.00 | 0.664 | 59.8 | 41.0 |
| 6.0 | 108.0 | 198.0 | 1.83 | 0.633 | 68.4 | 49.2 |
K0 by Mayne and Kulhawy (1982); the last column uses Jaky’s K0 = 1 − sin 33° = 0.455.
- At z = 1 m: σ′v = 18 kPa, OCR = (18 + 90)/18 = 6.00, K0 = 0.455 × 6.00sin 33° = 1.208 — more than twice the normally consolidated value.
- At z = 6 m: σ′v = 108 kPa, OCR = 1.83, K0 = 0.633.
- Thrust: integrating σ′h = K0γz down the wall gives P0 = 244.7 kN/m, acting 2.28 m above the base. Within 13 cm of the surface the formula would exceed Kp = 3.392, and K0 is held at Kp there; the effect on the thrust is negligible.
Had the sand been normally consolidated, P0 = ½ × 0.455 × 18 × 6² = 147.5 kN/m at H/3 = 2.00 m; a wall free to yield would carry only the active thrust, ½ × 0.295 × 18 × 6² = 95.5 kN/m. Overconsolidation adds 66 % to the at-rest thrust and lifts its line of action, because the extra pressure is concentrated near the top. The at-rest earth pressure module of GeoTerva gives each layer its own K0, by any of these relationships, with a water table at any depth.
7QuestionsShort answers.
Can K0 be greater than 1?
Yes. In an overconsolidated soil the horizontal stress can exceed the vertical one; with Mayne and Kulhawy’s relationship K0 = 1 is reached at OCR = 4.00 for φ′ = 30°. The upper limit is the passive coefficient Kp.
When should a wall be designed for K0 rather than Ka?
When it cannot move enough for the active state to develop: a wall propped by floors or struts, a culvert, an abutment on a stiff foundation. A free-standing cantilever or gravity wall that can rotate or slide a little (of the order of 0.1 % of its height in dense sand) is designed for the active pressure.
Does compaction of the backfill change K0?
Yes. Compaction behind a non-yielding wall locks in horizontal stress, so K0 can be well above 1 − sin φ′; Sherif, Fang and Sherif (1984) relate the increase to how much denser than its loosest state the fill is (Table 3).