GeoTerva Open the module

Formulas and tables · Pile foundations

β method for piles in clay: effective-stress skin friction

The skin friction of a pile in clay from the vertical effective stress and the remoulded friction angle (Burland, 1973), with the overconsolidation correction of Meyerhof (1976): β for φ′R = 15–35° and OCR = 1–8.

  • Free to read
  • φ′R = 15–35°
  • OCR = 1–8
  • Worked example

1The β methodEffective stress, long term.

Burland (1973) argued that the clay next to a driven pile is remoulded in a thin zone, that the excess pore pressures set up by driving dissipate from that thin zone fairly quickly, and that the shaft then fails in drained shear along a remoulded skin with no effective cohesion. The unit skin friction at depth z is then an effective-stress quantity:

f=Kσv′tan⁡φR′=βσv′

K is the coefficient of lateral earth pressure on the shaft, σ′v the vertical effective stress and φ′R the drained friction angle of the remoulded clay. The method uses neither cu nor an empirical adhesion factor: it describes the shaft after the clay has drained, which makes it the long-term counterpart of the α method.

2K and the overconsolidation ratioAt rest, raised by √OCR.

For a normally consolidated clay K is taken at rest, K = 1 − sin φ′R. For an overconsolidated clay Meyerhof (1976) raised it by the square root of the overconsolidation ratio, so that both cases are one expression:

K=(1−sin⁡φR′)OCR
β=(1−sin⁡φR′)tan⁡φR′OCR

At OCR = 1 this is the normally consolidated form. In a layered clay β is worked out for each layer and multiplied by the mean effective stress over that layer:

Qs=∑ipβiσ¯v,i′ΔLi

σ̄′v,i is the true mean over the layer, the area of the effective-stress diagram divided by the thickness, not the stress at mid-depth: the two differ when the water table crosses the layer. Within a layer f grows with depth in step with σ′v, and it steps where β changes at a boundary.

3Table of βφ′R = 15–35°, OCR = 1–8.

φ′R is measured on the remoulded clay, in a drained shear test on a remoulded specimen, and OCR comes from oedometer tests; neither is estimated from cu here.

Table 1. β = (1 − sin φ′R) tan φ′R √OCR against φ′R and OCR
φ′R (°)K, OCR = 1β, OCR = 1β, OCR = 1.5β, OCR = 2β, OCR = 3β, OCR = 4β, OCR = 6β, OCR = 8
150.7410.1990.2430.2810.3440.3970.4860.562
160.7240.2080.2540.2940.3600.4150.5090.587
170.7080.2160.2650.3060.3750.4330.5300.612
180.6910.2250.2750.3180.3890.4490.5500.635
190.6740.2320.2840.3280.4020.4640.5690.657
200.6580.2390.2930.3390.4150.4790.5870.677
210.6420.2460.3020.3480.4270.4930.6030.697
220.6250.2530.3090.3570.4380.5050.6190.715
230.6090.2590.3170.3660.4480.5170.6330.731
240.5930.2640.3240.3740.4580.5280.6470.747
250.5770.2690.3300.3810.4660.5380.6590.762
260.5620.2740.3350.3870.4740.5480.6710.775
270.5460.2780.3410.3930.4820.5560.6810.787
280.5310.2820.3450.3990.4890.5640.6910.798
290.5150.2860.3500.4040.4950.5710.7000.808
300.5000.2890.3540.4080.5000.5770.7070.816
310.4850.2910.3570.4120.5050.5830.7140.824
320.4700.2940.3600.4150.5090.5870.7200.831
330.4550.2960.3620.4180.5120.5910.7240.836
340.4410.2970.3640.4200.5150.5950.7280.841
350.4260.2990.3660.4220.5170.5970.7310.845

K = 1 − sin φ′R at OCR = 1; at any OCR, K = (1 − sin φ′R)√OCR. Burland (1973), Meyerhof (1976). Values computed by GeoTerva with the function its pile modules use.

4Worked exampleAn overconsolidated crust over a softer clay.

A driven pile D = 0.45 m, L = 15 m, passes through an overconsolidated crust and into a lightly overconsolidated clay; the water table is at 2 m (γw = 9.81 kN/m³). The perimeter is p = πD = 1.414 m.

Table 2. β method layer by layer
Layerγ (kN/m³)φ′R (°)OCRσ̄′v (kPa)βf̄ = βσ̄′v (kPa)Qs (kN)
0–6 m18.528442.420.56423.93203.0
6–15 m17.5241.5106.360.32434.41437.8
Total641
  • Upper layer, 0–6 m: β = (1 − sin 28°) tan 28° √4 = 0.564. σ′v rises to 37.0 kPa at the water table and 71.8 kPa at 6 m; the exact mean over the layer is σ̄′v = 42.42 kPa. The stress at mid-depth, 45.69 kPa, is 7.7 % higher, because the line bends at the water table. f̄ = 0.564 × 42.42 = 23.93 kPa and Qs,1 = 1.414 × 6 × 23.93 = 203.0 kN.
  • Lower layer, 6–15 m: β = (1 − sin 24°) tan 24° √1.5 = 0.324, σ̄′v = 106.36 kPa, f̄ = 34.41 kPa and Qs,2 = 1.414 × 9 × 34.41 = 437.8 kN.

Qs = 203.0 + 437.8 = 641 kN. Were the crust normally consolidated (OCR = 1), the upper layer would carry 101.5 kN instead of 203.0 kN. The point resistance is added separately (see pile end bearing in clay); the short-term shaft of the same pile follows from the α method or the λ method.

5QuestionsShort answers.

What is φ′R in the β method?

The drained friction angle of the clay in its remoulded state, with c′ = 0: the clay of the thin skin that installation leaves around the shaft. It is measured in a drained shear test on a remoulded specimen; the GeoTerva pile modules ask for it rather than estimate it.

When should the β method be used instead of the α method?

The β method gives the long-term, drained shaft resistance; the α method the short-term, undrained one. For a pile in soft, normally consolidated clay, and for a check of the shaft once the excess pore pressures of installation have dissipated, the β method is the natural choice; for the short-term capacity of a stiff clay the α method is usual.

What values does β take?

For a normally consolidated clay with φ′R = 20–30°, β = 0.239 to 0.289. Overconsolidation raises it by √OCR: at φ′R = 30° and OCR = 4, β = 0.577.

The theory behind it