Skip to the manual
GeoTerva Start free
User manual · Stresses in a soil mass

Westergaard point load stresses: user manual

Calculate the vertical stress increase at a point below one or several vertical point loads on layered ground, in the Westergaard model of soil with thin rigid horizontal layers: the stress at A, the lines of equal stress, colour contours, the profile with depth and a 3D view, the Results, the Profile view and the report giving Boussinesq’s value beside it. This manual walks through the screen, dragging, every input, the results and the report, with a worked example you can reproduce.

Updated 17 October 2026 · GeoTerva user manual

What the module calculates

Westergaard point load gives the increase in vertical stress at a point of the ground below one or several vertical point loads on the ground surface, in the ground model of Westergaard (1938): an elastic soil reinforced by numerous thin, rigid horizontal layers that allow no lateral strain. It stands for a clay with thin seams of sand, whose horizontal deformation the stiffer layers hold back. You choose the point A by its position x, y on the ground surface and its depth z, and the module gives Δσz there, the lines of equal stress, the colour contours, the profile with depth under A and a 3D view; the Results, the Profile view and the report also give the value that Boussinesq’s solution (a uniform, isotropic half-space) gives for the same load and point, so you see what the layering changes.

For one load P at the horizontal distance r from A and the depth z, in soil whose Poisson’s ratio between the rigid layers is μs:

Δσz = (P/z²) I5, I5 = 1/(2πη²) · [(r/ηz)² + 1]−3/2, η = √[(1 − 2μs) / (2 − 2μs)]

I5 is the influence value. It depends on r/z and on μs only. With several loads each acts alone with its own distance r from A, and the stresses are added (the ground is elastic, so they superpose).

What you can describe

  • One to eight vertical point loads, each with its own force P and its own position xL, yL on the ground surface; no two loads may stand at the same place.
  • The point A: its position x, y on the ground surface and its depth z.
  • The Poisson’s ratio μs of the soil between the rigid layers.
  • The depth of the profile zmax, down to which the Profile view and the table under A run.

The result is the increase caused by the loads only; the overburden pressure of the soil above A is not included, so add it where your design needs the total stress. The module draws the section with the lines of equal stress, the colour contours, the profile and a 3D view, writes out the working and prepares a PDF or Word report.

Which module for which load

Before you start: what you need

Have these ready from your design:

WhatNotes
The loads PFrom your design loading. Vertical forces on the ground surface, zero or more, up to eight. A load of zero is accepted and adds nothing.
Their positions xL, yLFrom the layout. On the ground surface, in one set of coordinates with the point A; any value; no two loads at the same place.
The point A: x, y, zWhere you want the stress. x and y in the coordinates of the loads; z at least 0.001 m below the surface.
Poisson’s ratio μsYour judgement of the layered soil. From 0 to 0.49; at 0.5 the soil between the layers could not deform at all, so the module stops at 0.49.

Quick start in seven steps

  1. Open the module and choose the units

    Open Westergaard point load from the Stresses in a Soil Mass family. Pick SI · kN, SI · tf or US in the header; you can change it at any time.

  2. Enter the loads

    In Point loads the first load is already in the table. Press its row to change P, xL and yL. To add another, fill the New point load form and press + Add point load.

  3. Place the point A

    In Point of interest type x, y and z, or drag the blue point on the Section drawing.

  4. Set Poisson’s ratio

    In Westergaard material type μs (0 to 0.49).

  5. Set the depth of the profile

    In Depth profile type zmax, or drag the dashed line at the foot of the Section drawing.

  6. Press Analyze

    Press Analyze at the foot of the Model tab. The bar reads Analysed and the loads lock; the point A and the profile depth stay free.

  7. Read the answer

    The Results tab gives Δσz at A with the Boussinesq value beside it, I5 for one load, the part from each load for several, and a table of the stress against depth under A. The lines of equal stress are on the Section drawing, the colour bands in Contours. The Calculations tab writes out the working and the Report tab saves a PDF or a Word file.

The screen: section, contours, profile and 3D

The layout is the one every GeoTerva module shares, described in the workspace guide. The drawing has four views, chosen with the buttons above it:

  • Section is a vertical cross section with the load arrow(s) on the ground, the point A with its dimensions and the dashed line of the profile depth. For one load it is the plane through the load and A, with the horizontal distance r from the load as its axis (the solution is the same all round the load). For several loads it is the vertical plane y = yA through A, parallel to x; loads that stand beside the plane are marked “beside the plane” with their distance and act on it as well. After Analyze it adds the lines of equal stress and a label with Δσz at A.
  • Contours is the same section filled with colour bands of Δσz on a logarithmic scale, with a legend in kPa.
  • Profile is the curve of Δσz against depth under A for Westergaard’s solution (solid) and Boussinesq’s (dashed), with a marker at the depth of A.
  • 3D is an oblique view of the ground block with the axes x, y and z, the load arrow(s), the distances from the load to A and a small element at A with the stress on it.

Before Analyze the drawings follow the inputs and say “The stress and the lines of equal stress appear after Analyze” (Section), “The colour contours of the stress appear after Analyze” (Contours), “The profile appears after Analyze” (Profile) or “The stresses on the element appear after Analyze” (3D).

The Section view before Analyze: the load arrow P = 5.0 kN on the ground, the point A with its distances r = 5.00 m and z = 4.00 m, the dashed line of the profile depth and the hint under the drawing.
Section before Analyze.
The Section view after Analyze: the lines of equal stress labelled 0.5, 0.2, 0.1, 0.07, 0.05, 0.02, 0.011 (the line through A) and 0.01 kPa below the load, the point A with the label Δσz = 0.01058 kPa and the line through A drawn in blue.
Section after Analyze: the lines of equal stress; the line through A (0.011 kPa) is blue.
The Contours view after Analyze: colour bands from dark red under the load to blue far away, a legend from 0.001 to 0.5 kPa, the point A and the dashed line of the profile depth.
Contours after Analyze.
The Profile view after Analyze: the Westergaard curve (solid) and the Boussinesq curve (dashed) of the stress against depth under the point, with the marker at z = 4.00 m reading 0.01058 and 0.01419.
Profile after Analyze: Westergaard solid, Boussinesq dashed.
The 3D view after Analyze: the ground block with the load arrow P = 5.0 kN, the axes x, y and z, the distances x = 3.00, y = 4.00, z = 4.00 and r = 5.00, and an element at A with Δσz = 0.01058.
3D after Analyze.

The 3D view ends with the line “A negative Δσ is a decrease (tension) in the elastic solution.” The solution of this module gives positive values for the loads it describes.

The Show chips

Above the Section drawing a bar has two chips: Lines of equal stress and Dimensions. The lines chip is off and greyed out until you press Analyze, and then turns on; Dimensions is on by default. The Contours view has the same two chips under the heading Show; there the lines chip is off by default, so that the lines can be laid over the colours. The Profile and 3D views have no chips.

The Contours view with the chip Lines of equal stress switched on: lines of equal stress drawn over the colour bands.
Contours with the lines of equal stress laid over the colours; the labels sit on blank boxes, so read the values in the Section view.

Dragging on the drawing

The hint under the Section drawing reads “Drag the point A to place it” and “Drag the dashed line to set the depth of the profile”; with several loads it also tells you to drag a load to move it. What each pull does, as the module runs it:

  • The point A, one load. Drag the blue point in the Section or Contours view: it moves in the plane through the load and A, so x and y change together (the direction from the load stays, the distance r follows the pointer, and x and y are rounded to 1 cm) and z follows in steps of 5 cm. From the example, pulling A 60 px right and 40 px down gave x = 3.9 m, y = 5.2 m, z = 5 m. The depth stops at 0.05 m at the top and at the foot of the drawn frame at the bottom; the distance stops at the sides of the frame.
  • The point A, several loads. The Section is the plane y = yA, so a pull changes x and z only; y stays.
  • The dashed line. Drag it up or down to set zmax; it stops at 0.5 m at the top.
  • A load, several loads. In the Section and Contours views each load arrow can be dragged sideways: xL follows in steps of 5 cm and yL stays. In the 3D view a load can be dragged over the ground and xL and yL both change.
  • A single load cannot be dragged in the Section or Contours view (its arrow is the axis of the drawing); in the 3D view it can.
  • No two loads on one place. A pull that would put a load on another stops at the nearest free place and a message says “Another point load already stands at this position — the value is kept as it was.”
  • After Analyze the loads are locked: the load handles are gone. The point A and the dashed line stay free, and so do the boxes x, y, z and zmax.

Zoom

Each view has −, a percentage and + at the lower right, and a button that fits the whole drawing in the pane. Zoom is a property of the drawing only: it is not saved with the model and does not change the report.

Entering the model, section by section

The Model tab has five sections: Model data, Point loads, Point of interest, Westergaard material and Depth profile. Each opens when you click its title; Next and Back at the foot walk you through them, and Analyze waits below the last one. Lengths are in m in both SI systems and in ft in US; forces are in kN, tf and kip for SI · kN, SI · tf and US. Defaults are shown in SI; in US the boxes show the converted values, for example 20 m is 65.6168 ft and the form opens with 1.12404 kip at 13.1234 ft. In US the row of the Point loads table keeps the labels kN and m although the numbers are converted; read the unit in the form.

Model data

The first section holds the model name, Save to file…, Open file…, Quick Save… with its list and Load and Delete, and Reset to defaults. It works as described in the workspace guide.

The Model data section with the model name, Save to file, Open file, Quick Save, Reset to defaults and the quick-save list with Load and Delete.
Model data.

Point loads

The section is a form over a table. The New point load form takes P, xL and yL; + Add point load puts the load into the Point loads table, and a counter beside the button shows how many of the eight loads there are. The table lists each load with its force and position. Press a row to change that load in the form (the form then reads Editing · Point load 1 and offers Done and Delete point load; the note says that changes apply as they are entered), or press × to take a load out. The first load is already in the table when the module opens, and Delete point load in the form and × in the table are greyed out while it is the only one.

The Point loads section: the New point load form with P = 5 kN, xL = 4 m and yL = 0 m, the Add point load button with the counter 1 of 8, and the table with Point load 1.
Point loads: the form over the table.
Point load fields (the form, and each row of the table)
FieldDefaultWhat to enter
Point load P
kN · tf · kip
5 (load 1) · 5 (form)The vertical force on the ground surface. Zero or more.
Position along x xL
m · ft
0 (load 1) · 4 (form)Any value. A load added later starts at 4 m.
Position along y yL
m · ft
0Any value.
The Point loads section with the row of load 1 pressed: the form reads Editing, Point load 1, shows P, xL and yL with the Done and Delete point load buttons.
A row of the table pressed: the load is edited in the form.

The loads are listed in the order you add them, and their numbers name the results “From point load 1”, “From point load 2” and so on. No two loads may stand at the same place: adding a load at a position that is taken, or typing such a position into a row, is refused (see Messages).

The Point loads section with two loads in the table: Point load 1 with P = 5 kN at xL = 0 m, yL = 0 m and Point load 2 with P = 5 kN at xL = 4 m, yL = 0 m; the counter reads 2 of 8.
Two loads in the table.

Point of interest

The three coordinates of the point where you want the stress. A is under the ground surface at the position x, y and the depth z; the drawing shows the same distances as dimensions. For one load the solution depends on r = √[(x − xL)² + (y − yL)²] and z only.

The Point of interest section with x = 3 m, y = 4 m and the depth z = 4 m.
Point of interest.
Point of interest fields
FieldDefaultWhat to enter
Point A: x on the ground surface x
m · ft
3In the same coordinates as the loads.
Point A: y on the ground surface y
m · ft
4In the same coordinates as the loads.
Depth of the point z
m · ft
4At least 0.001 m below the ground surface.

Westergaard material

The one soil constant: Poisson’s ratio μs of the soil between the rigid layers. The note in the section explains the medium: elastic soil with closely spaced thin rigid horizontal sheets that allow no lateral strain, an idealisation of a clay with thin sand seams, and μs must stay below 0.5.

The Westergaard material section with Poisson’s ratio μs = 0.3.
Westergaard material.
Westergaard material field
FieldDefaultWhat to enter
Poisson’s ratio of the soil between the rigid layers μs
—
0.3From 0 to 0.49.

Depth profile

The depth down to which the Profile view and the table of the stress under A run.

The Depth profile section with the depth of the profile zmax = 20 m.
Depth profile.
Depth profile field
FieldDefaultWhat to enter
Depth of the profile zmax
m · ft
20At least 0.1 m. The Profile view and the table under A go from the surface down to this depth, or to the depth of A if that is deeper.

The Westergaard medium, Boussinesq beside it, and several loads

What Poisson’s ratio does

μs enters through η = √[(1 − 2μs)/(2 − 2μs)]: η = 0.7071 at μs = 0, 0.5345 at 0.3 and 0.1400 at 0.49. Its effect depends on where A lies:

  • Under the load (r = 0) the influence value is 1/(2πη²), so it rises with μs. At z = 4 m under a 5 kN load the module gives 0.09947 kPa with μs = 0 (I5 = 0.3183), 0.1741 kPa with 0.3 (I5 = 0.5570) and 0.2984 kPa with 0.4 (I5 = 0.9549); Boussinesq gives 0.1492 kPa.
  • At 5 m from the load in the example (r/z = 1.25) a higher μs gives a lower stress: 0.01187 kPa at 0, 0.01129 at 0.2, 0.01058 at 0.3, 0.008930 at 0.4 and 0.003500 at 0.49.

Westergaard beside Boussinesq

The Results, the depth table, the Calculations tab and the report give Boussinesq’s value for the same load and point, and the Profile view draws both curves. In the example (5 kN, r = 5 m, z = 4 m) Westergaard gives 0.01058 kPa and Boussinesq 0.01419 kPa. The Westergaard curve lies below the Boussinesq curve at moderate depths and the two come together deeper down; at z = 20 m they are 0.005175 and 0.005129 kPa. Close to the surface, away from the load, Westergaard’s value is the larger: 0.006364 against 0.004217 kPa at z = 2 m. The Calculations tab gives the ratio Westergaard/Boussinesq (0.745 for the example).

Several loads

The number of loads, from 1 to 8, is made by adding and deleting loads. The stress of each load is found as if it were alone, with its own distance r from A, and the stresses are added; the Boussinesq values are added in the same way.

  • All positions are in one set of coordinates. xL, yL and A’s x, y refer to the same origin. Only the distance counts: A at (4, 3), (5, 0) or (−3, −4) with the load at the origin gives the same stress, 0.01058 kPa, and so does the load at (2, 1) with A at (5, 5) (0.01058 kPa).
  • Loads can differ. Each load has its own P.
  • The cards show the parts. The Results tab shows the total, Boussinesq’s total and a card for the part from each load for two or three loads (from four loads the parts are listed under the cards); the Calculations tab writes out each load’s working.

With the example load and a second load of 5 kN at xL = 4 m, yL = 0 the second load is 4.12 m from A and adds 0.01698 kPa to the 0.01058 kPa of the first: 0.02756 kPa in all (Boussinesq 0.03862 kPa). Make that second load 10 kN and the total is 0.04455 kPa; put it 20 m away and it adds almost nothing (0.01089 kPa). A third load of 5 kN at (0, 6) gives 0.05066 kPa. Eight loads of 5 kN, 1 m apart along x from 0 to 7, give 0.1090 kPa (Boussinesq 0.1525).

The Section view of two loads, P1 and P2 of 5.0 kN, in the plane y = 4 m through A, both marked 4.00 m beside the plane, with the lines of equal stress of the sum labelled 0.015, 0.02 and 0.028 kPa and the point A with the label Δσz = 0.02756 kPa.
Two loads: the lines of equal stress of the sum in the plane through A.
The Contours view of the same two loads: the colour bands of the sum in the plane y = 4 m.
The same two loads in the Contours view.
The 3D view of the same two loads: the arrows P1 and P2 on the ground, the axes and an element at A with Δσz = 0.02756.
The same two loads in 3D.

Which should I use?

  • Layered ground with horizontal seams that restrain lateral strain: this module. Ground you treat as uniform: Point load.
  • A load spread over an area is not a point load: use Westergaard areas for layered ground or Rectangle for uniform ground. A point load is the right model when the loaded area is small compared with its distance to A.

Analyze and read the results

Press Analyze. The bar changes to Analysed — the stress at the point calculated and says “The inputs are locked. Edit inputs clears the results; the unit system can still be changed. The point A stays free: drag it on the drawing or change its coordinates, and the stress there is calculated at once.” A message appears briefly, “Analysed — see the Results tab and the Calculations.” The module stays on the Model tab: open Results for the answer. The Section view now shows the lines of equal stress.

The Analysed bar: Analysed — the stress at the point calculated, the message about the locked inputs and the free point A, the Warnings (0) button and the Edit inputs button.
The bar after Analyze.
The Results tab: the cards Vertical stress increase (Westergaard) 0.01058 kPa, Influence value 0.03386 and Boussinesq, for comparison 0.01419 kPa, with the note that the overburden pressure is not included.
The cards of the example.
CardSymbolThe example
Vertical stress increase (Westergaard)Δσz0.01058 kPa
Influence value (one load)I50.03386
Boussinesq, for comparisonΔσz,B0.01419 kPa
From point load k (two or three loads)Δσz(k) the part of the total from load k

Below the cards a Values, step by step table lists the steps of the Calculations tab with their values, and the Vertical stress increase under the point table gives z, Δσz (Westergaard) and Δσz,B (Boussinesq) at ten equal steps from the surface to zmax, with the row of A inserted and highlighted. For one load it also gives r/ηz and I5; with several loads those two columns are left out. If zmax is less than the depth of A, the table runs to the depth of A.

The table Vertical stress increase under the point with the columns z, r/ηz, I5, Δσz Westergaard and Δσz Boussinesq: 2.000 m, 4.000 m (highlighted, 0.01058 and 0.01419 kPa), 6.000 m and on to 20.00 m.
The depth table of the example.
The Results tab of two loads: the total 0.02756 kPa, Boussinesq 0.03862 kPa and the parts 0.01058 kPa from point load 1 and 0.01698 kPa from point load 2.
Two loads: the total, Boussinesq and the part from each.

Using the numbers

  • The result is an increase, not the total stress: add the overburden pressure of the soil above A for the total vertical stress.
  • The values are small for the example because the load is 5 kN; they scale with the load. Read the digits as the module gives them (four significant figures).
  • Change x, y or z after Analyze and everything follows at once; to change a load, press Edit inputs, which unlocks the loads and clears the results.
  • Changing the unit system after Analyze re-states the cards and the report without a new run. The drawings keep their labels in m and kPa.
  • Values are rounded where they are drawn, so the last digit of a figure on the drawing can differ by one from the card.

Warnings

The bar carries a Warnings (0) button. It opens a window that says “No warnings — the assumptions of the solution hold for these inputs.” The runs of this manual, from the default to eight loads and from μs = 0 to 0.49, gave no warning.

The window Warnings (0) with the text No warnings — the assumptions of the solution hold for these inputs, and a Close button.
The Warnings window.

The Calculations tab, the report and the Theory tab

The Calculations tab opens with Given and what is sought and then writes out the working in numbered steps, ending with the answer. For one load:

  1. The constant η from μs, with your numbers.
  2. The influence value I5 — the distance r (from the load to A on the ground), r/(ηz), 1/(2πη²) and I5.
  3. The stress — Δσz = (P/z²) I5 with your numbers, Boussinesq’s value at the same point and the ratio Westergaard/Boussinesq.
  4. The stress against depth — the same down the vertical line through A, as the table of the Results tab, with the row of A marked.

With several loads step 2 and 3 become one step for each load (its position, r, r/(ηz), I5, Δσz(k) and Boussinesq’s value), followed by a Superposition step that adds the parts, then the depth table. The working ends with the line “Answer.”.

The Calculations tab of two loads: step 2 Stress from point load 1, step 3 Stress from point load 2 and step 4 Superposition, with r = 5.00 m and 4.12 m, I5 = 0.03386 and 0.05434, the parts 0.01058 and 0.01698 kPa and the sum 0.02756 kPa.
The Calculations tab of two loads: the steps for each load and the superposition.

The report

In the Report tab fill in the cover (project, location, client, report number, date, prepared by, title or qualification, checked by, and optional notes). The details are kept in this browser and saved with the model file. Save as PDF and Download Word (.docx) produce the summary report; the preview below the buttons is the report itself.

The report has six parts: 1 Introduction and scope, 2 Input data, 3 Calculation, 4 Results, 5 Summary and 6 References. It carries three drawings, the Section with the lines of equal stress, the Profile and the 3D view, and states the units used.

The Report tab: the cover form with project, location, client, report number, date, prepared by, title, checked by and notes, the Save as PDF and Download Word buttons, and the cover page of the report with the table of the load, the point, the soil and the results and the conclusion sentence.
The Report tab: the cover details, the two buttons and the first page.

The Theory tab

The Theory tab has four sections: Westergaard’s medium, The solution, Worked example and References. Each opens when you click its title (Open all and Close all open or close them together). They describe the medium of thin rigid sheets, give the equations, draw I5 against r/z for μs = 0, 0.2 and 0.4 beside Boussinesq’s influence value, tabulate I5, and work the module’s own example; the figures are computed from the equations.

Worked example: the module’s own example

The module opens on this example, so you can follow the numbers on your own screen.

Inputs of the example
SectionInputValue
Point loadsPoint load 1P = 5 kN at xL = 0, yL = 0
Point of interestPositionx = 3 m; y = 4 m; z = 4 m
Westergaard materialPoisson’s ratioμs = 0.3
Depth profileDepthzmax = 20 m

Step 1: the constant η

η = √[(1 − 2 × 0.3)/(2 − 2 × 0.3)] = √(0.4/1.4) = 0.5345

Step 2: the influence value

The horizontal distance of A from the load is r = √(3² + 4²) = 5.00 m. Then r/(ηz) = 5/(0.53452 × 4) = 2.3385, 1/(2πη²) = 0.55709 and [2.3385² + 1]−3/2 = 0.06078, so

I5 = 0.55709 × 0.06078 = 0.03386

Step 3: the stress

Δσz = (P/z²) I5 = (5/4²) × 0.03386 = 0.01058 kPa

Boussinesq’s solution gives 0.01419 kPa at the same point, so Westergaard/Boussinesq = 0.745. These are the three cards of the Results tab and the steps of the Calculations tab. The same equations worked independently give every value of the depth table, for example 0.006364 kPa at 2 m, 0.01218 kPa at 6 m and 0.009489 kPa at 12 m.

Other unit systems

The same load in SI · tf, with P = 1 tf (the other values unchanged), gives 0.002116 t/m²: I5 is unchanged and (1/4²) × 0.03386 = 0.002116. In US the default example (5 kN is 1.124 kip) gives 0.0002210 ksf: 0.01058 kPa is 0.000221 ksf. A check by hand with round US numbers: P = 10 kip at the origin and A at x = 9 ft, y = 12 ft, z = 12 ft gives r = 15 ft, r/z = 1.25 as in the example, so I5 = 0.03386 and Δσz = (10/12²) × 0.03386 = 0.002351 ksf; the module gives 0.002351 ksf. With P = 1 kip and A 10 ft from the load at 10 ft depth (r/z = 1) it gives 0.0005835 ksf and I5 = 0.05835, the same as the equations.

How each input changes the answer

Each row changes one thing in the example (one load of P = 5 kN at the origin, A at x = 3 m, y = 4 m, z = 4 m, μs = 0.3, zmax = 20 m) and runs the module again, in SI · kN. The numbers are the ones the module gives, so you can reproduce any row; an independent calculation with the same equations agrees with every row.

The example with one change at a time
ChangeΔσz (kPa)I5
The example0.010580.03386
P = 10 kN
Proportional to the load
0.021160.03386
P = 20 kN
Four times the stress
0.042320.03386
z = 0.5 m
Near zero close to the surface
0.0016940.00008471
z = 2 m
Larger than Boussinesq here
0.0063640.005092
z = 6 m
Near the maximum
0.012180.08767
z = 8 m
Past the maximum
0.011950.1529
z = 12 m0.0094890.2733
z = 20 m
Close to Boussinesq
0.0051750.4140
x = 0, y = 0
A under the load
0.17410.5570
x = 2, y = 0
2 m from the load
0.067800.2170
x = 10, y = 0
10 m from the load
0.0015910.005092
x = 6, y = 8
Also 10 m away: same as above
0.0015910.005092
x = 4, y = 3
Also 5 m away: same as the example
0.010580.03386
x = −3, y = −4
Also 5 m away: same as the example
0.010580.03386
μs = 0
Higher stress at this distance
0.011870.03799
μs = 0.20.011290.03614
μs = 0.40.0089300.02858
μs = 0.49
The largest value accepted
0.0035000.01120
Load (2, 1), A (5, 5)
Still 5 m apart
0.010580.03386

Several loads, SI · kN, from the example (a second load added with the values shown):

Adding loads
AddedTotal (kPa)Parts (kPa)
Load 2: 5 kN at (4, 0)
4.12 m from A
0.027560.01058 + 0.01698
Load 2: 10 kN at (4, 0)0.044550.01058 + 0.03396
Load 2: 5 kN at (20, 0)
Far from A: almost no change
0.010890.01058 + 0.0003124
Load 2: 5 kN at (3, 4)
Directly above A, 0 m away
0.18470.01058 + 0.1741

The pattern follows the equations. The stress is proportional to P; I5 depends on r/z and μs only. Halving the depth (z = 2 m, r = 5 m) and doubling the distance (r = 10 m, z = 4 m) both give r/z = 2.5, and both rows show the same I5 = 0.005092; the stress is highest under the load and, at a fixed distance, rises to a maximum at some depth and then falls; and at a given r/z the sign of the μs effect follows the position of A, as the section above shows. The depth of the profile zmax changes the table and the Profile view but not the stress at A: 0.01058 kPa with zmax = 6 m and 0.01058 kPa with zmax = 2 m, a depth the table extends to the depth of A.

Messages: when the module stops, and what it notes

The module checks the numbers it needs before it calculates. When an input cannot be used, press Analyze and a window titled Cannot analyse — 1 input error (or 2 input errors …) lists each message; nothing is calculated. A load row whose force is negative is outlined in red.

The window Cannot analyse, 1 input error: Depth of the point (z) must be at least 0.001 m.
The window Analyze opens when the depth is zero.
WhenMessage and what to do
z is 0 or negative“Depth of the point (z) must be at least 0.001 m.” Enter a depth of at least 0.001 m.
μs is 0.5 or more“Poisson's ratio of the soil between the rigid layers (μs) must be at most 0.49.” Enter a value up to 0.49.
μs is negative“Poisson's ratio of the soil between the rigid layers (μs) must be at least 0.” Enter zero or a positive value.
P is negative“Point load 1 (P1) must be at least 0 kN.” Enter zero or a positive load.
zmax is 0“Depth of the profile (zmax) must be at least 0.1 m.” Enter a depth of at least 0.1 m.
A box is empty“Depth of the point (z) is missing.” Fill the box. The same words appear for x, y, μs, P and a load position.
Two inputs are wrongOne window lists both: “Depth of the point (z) must be at least 0.001 m. Poisson's ratio of the soil between the rigid layers (μs) must be at most 0.49.”
A new load would stand on anotherA message appears briefly: “A point load already stands at this position. Give the new one another position.” The load is not added.
A position typed or dragged onto another loadA message appears briefly: “Another point load already stands at this position — the value is kept as it was.”

The messages use the numbered names of the loads, such as “Point load 2 (P2)” and “Position of load 1 along x (xL,1)”, and the limits in the units of the unit system chosen. A negative force typed into the New point load form is added to the table with its row marked in red, and Analyze then stops with “Point load 2 (P2) must be at least 0 kN.” At eight loads + Add point load is greyed out and the counter reads 8 of 8.

Notes and warnings

With every input inside its limits the module calculates, and the Warnings window reads “No warnings — the assumptions of the solution hold for these inputs.” A load of zero is accepted and gives 0 kPa. A point very close to a load gives a very large stress, as the equation does: with A directly under the load at z = 0.01 m the module gives 27,852 kPa for 5 kN (I5 = 0.5570, the value under the load at μs = 0.3). A very large depth is accepted too: z = 100,000 m gives 2.79e-10 kPa. Very small and very large values are shown in exponent form.

Good practice and common mistakes

  • Use the module for a soil that fits the model. Westergaard’s medium is an idealisation: the rigid layers allow no lateral strain. Where the ground is better described as a uniform half-space, Point load is the model; the Boussinesq column here lets you see how far apart the two are.
  • Choose μs for the soil between the layers. It sets η; the values the module accepts are 0 to 0.49. Run the example at a few values (the table above) to see how much it matters at your r/z.
  • Use one set of coordinates. xL, yL of every load and x, y of A refer to the same origin; only the distance between a load and A counts.
  • Enter forces, not pressures. P is a force. For a load spread over an area use Westergaard areas.
  • Keep a point load a point. At a distance from A of the order of its own size or less, a real footing is not a point load.
  • Add the overburden. The result is the stress increase; for the total vertical stress add the soil weight above A.
  • Place A with the drawing, then type exact values. Dragging snaps to a few centimetres; type the coordinates when you need a given place. In 3D a pull has no stop at the frame, so check the load row after a long pull.
  • Check the units after switching the system: type values in the units shown beside the boxes.
  • Keep a record. The report is the record of an analysis; use Quick Save… or Save to file… to keep the model.

Frequently asked questions

How is the stress below a point load calculated here?

By Westergaard’s solution for soil reinforced by thin rigid horizontal layers: Δσz = (P/z²) I5 with I5 = 1/(2πη²) · [(r/ηz)² + 1]−3/2 and η = √[(1 − 2μs)/(2 − 2μs)]. For the module’s example it gives 0.01058 kPa.

What is the influence value I5?

It is the stress increase multiplied by z² and divided by the load. It depends only on r/z and μs, and under the load it equals 1/(2πη²), for example 0.5570 at μs = 0.3. The module gives it for one load; with several loads it gives the stress of each.

How does Westergaard differ from Boussinesq?

Boussinesq treats the ground as a uniform half-space; Westergaard treats it as an elastic soil with thin rigid layers that stop lateral strain, so it spreads the load differently. The module shows both: in the example 0.01058 kPa against 0.01419 kPa. Under the load Westergaard’s stress is the larger at μs = 0.3; at 5 m from it, at moderate depths, the smaller.

Does the result include the weight of the soil?

No. It is the increase caused by the loads only. Add the overburden pressure of the soil above A for the total vertical stress.

How many loads can I add, and can they stand at the same place?

Up to eight, each with its own P, xL and yL. No two may stand at the same place; the module refuses a load that would. The stresses of the loads add.

Can I drag the loads and the point on the drawing?

Yes. Drag A and the dashed line at any time; before Analyze you can also drag the loads: with several loads a load arrow in the Section and Contours views (along x) and over the ground in the 3D view, and one load in 3D only. After Analyze the loads are locked.

What values does the module accept?

P zero or more, z at least 0.001 m, μs from 0 to 0.49, zmax at least 0.1 m, and x, y, xL and yL any value. Anything else stops the analysis with a message that names the value.

Why can Poisson’s ratio not be 0.5?

At μs = 0.5 the constant η is zero: soil that cannot change volume and cannot strain sideways could not deform at all, and the equation breaks down. The module stops at 0.49 (η = 0.1400).

What do the lines of equal stress show?

Each line joins the points of the section with the same Δσz, labelled in kPa; the line through A is blue. Switch them on and off with the Lines of equal stress chip. The Contours view shows the same stress as colour bands on a logarithmic scale.

Which units does it use, and what are the units of the answer?

SI · kN, SI · tf or US, switchable in the header at any time, even after Analyze. Stresses are in kPa, t/m² or ksf, forces in kN, tf or kip and lengths in m or ft. The default example gives 0.01058 kPa, 0.002116 t/m² with a load of 1 tf, or 0.0002210 ksf.

What does the report contain?

A cover with your project details and the answer, then six parts: introduction and scope, input data, the calculation step by step, results, summary and references, with the section, profile and 3D drawings. It is saved as a PDF or a Word file once the model is analysed.

Does the module remember my inputs?

Yes. Every change is kept in the browser, and the page opens again on the model you last worked on, including its analysed state. Reset to defaults brings back the example; Save to file and Quick Save keep copies.