Skip to the manual
GeoTerva Start free
User manual · Stresses in a soil mass

Stresses below a loaded rectangle: user manual

Calculate the vertical stress increase at any point below or beside one or several uniformly loaded flexible rectangles: the stress at A, the lines of equal stress, colour contours, the profile with depth and a 3D view. This manual walks through the screen, dragging, every input, the results and the report, with a worked example you can reproduce.

Updated 17 October 2026 · GeoTerva user manual

What the module calculates

Rectangle gives the increase in vertical stress at any point of the ground below or beside one or several flexible rectangular areas, each carrying a uniform pressure q on the ground surface. The ground is a homogeneous, isotropic, elastic half-space, and the solution is the one found by integrating Boussinesq’s point-load solution over the rectangle. You place the point A by its three coordinates, x and y on the ground and the depth z, and the module gives Δσz there, the lines of equal stress, the colour contours, the profile with depth under A and a 3D view.

Below a corner of a rectangle with sides L and B the stress is Δσz = q I3, where the influence factor I3 depends on m and n, the two sides divided by the depth:

I3 = (1/4π) [ 2mn√(m² + n² + 1)/(m² + n² + m²n² + 1) · (m² + n² + 2)/(m² + n² + 1) + tan⁻¹( 2mn√(m² + n² + 1)/(m² + n² + 1 − m²n²) ) ]

For any other point the module writes the loaded rectangle as the sum of four rectangles that all have a corner directly above A. Each is added or subtracted, so the point may lie under the area, on its edge or outside it. With several rectangles the stress of each is found in the same way and the stresses are added.

What you can describe

  • One to eight rectangular loads, each with its own load per unit area q, its side L along x, its side B along y and the position xc, yc of its centre on the ground.
  • The point A: x and y on the ground surface and the depth z below it.
  • The depth of the profile zmax, down to which the Profile view and the table under A run.

The result is the increase caused by the rectangles only; the overburden pressure of the soil above A is not included, so add it where your design needs the total stress. The module draws the section, the contours, the profile and a 3D view, writes out the working and prepares a PDF or Word report.

Which module for which load

  • A footing, raft or slab that is rectangular in plan: this module. A load that is long compared with the depth you ask about is close to a strip: Vertical strip load.
  • A circular footing or tank: Circle, any point.
  • A load of any other shape in plan, such as an L-shaped slab with an irregular edge: Influence chart. A shape made of rectangles can also be built here, as several rectangles that meet at their sides.
  • A concentrated load: Point load; a load along a line: Vertical line load.
  • A trapezoidal fill: Embankment.
  • Layered ground, where a stiff layer spreads the load: Westergaard areas.

Before you start: what you need

Have these ready from your design:

WhatNotes
The load per unit area q
Your design loading
The pressure the rectangle puts on the ground, zero or more. It is a pressure, not a total force.
The sides L and B
The footing, raft or slab
L is the side along x and B the side along y, each at least 0.001 m. Either may be the longer one.
The centre xc, yc
The layout
The place of the centre on the ground. With one rectangle you can leave it at the origin and measure A from the centre.
The point A: x, y, z
Where you want the stress
x and y in the same coordinates as the centres; z at least 0.001 m below the surface.

Quick start in seven steps

  1. Open the module and choose the units

    Open Rectangle from the Stresses in a Soil Mass family. Pick SI · kN, SI · tf or US in the header; you can change it at any time.

  2. Enter the rectangle

    In Rectangular loads the first rectangle is already in the table. Press its row to change q, L, B, xc and yc, or drag the rectangle on the drawing. To add another, fill the New rectangular load form and press + Add rectangular load.

  3. Place the point A

    In Point A type x, y and z, or drag the blue point on the Section drawing (it sets x and z).

  4. Set the depth of the profile

    In Depth profile type zmax, or drag the dashed line at the foot of the Section drawing.

  5. Press Analyze

    Press Analyze at the foot of the Model tab. The bar reads Analysed and the rectangles lock; the point A and the profile depth stay free.

  6. Read the answer

    The Results tab gives Δσz at A, the influence value Δσz/q for one rectangle, the part from each rectangle for several, and a table of the stress against depth under A. The lines of equal stress are on the Section drawing, the colour bands in Contours.

  7. Move A and take the report

    Drag A or change x, y and z: the stress there is calculated at once. The Calculations tab writes out the working; the Report tab saves a PDF or a Word file.

The screen: section, contours, profile and 3D

The layout is the one every GeoTerva module shares, described in the workspace guide. For this module the drawing has four views, chosen with the buttons above it:

  • Section is a vertical cut through the ground in the plane y = yA, the plane through A parallel to the x axis, with the rectangles that the plane cuts drawn on the ground. It shows the point A, the dimensions z and x (with several rectangles, or one that is not centred at the origin, x − x₁: the distance of A from the centre of rectangle 1) and the dashed line of the profile depth. After Analyze it adds the lines of equal stress and a label with Δσz at A. Under the load a red note says whether the plane cuts it (“the section cuts the loaded area”) or not (“the loaded area lies beside this section (y outside the rectangle)”). With several rectangles, one the plane misses is drawn dashed with its distance, for example “6.00 m beside the plane”, and still acts on the section from beside; the subtitle says so.
  • Contours is the same section filled with colour bands of Δσz on a logarithmic scale, with a legend in kPa and in per cent of q (with several rectangles the percentage header reads “% of q max”).
  • Profile is the curve of Δσz against depth under A, with a marker at the depth of A.
  • 3D is an oblique view of the rectangles on the ground, the axes x, y and z, and a small element at A with the stress on it.

Before Analyze the drawings follow the inputs and say “The stress and the lines of equal stress appear after Analyze” (Section), “The colour contours of the stress appear after Analyze” (Contours), “The profile appears after Analyze” (Profile) or “The stresses on the element appear after Analyze” (3D). The small rings at the edges of the rectangle are its grips.

The Section view before Analyze: the Lines of equal stress chip unchecked and Dimensions checked, the rectangle of 150 kPa on the ground with a ring at each end, the point A with its distances x = 2.50 m and z = 4.00 m, and the dashed line of the profile depth.
Section before Analyze.
The Section view after Analyze: the loaded rectangle with the lines of equal stress labelled 50, 30, 20, 15 and 11 kPa, the point A with the label Δσz = 10.9 kPa and the line through A drawn in blue.
Section after Analyze: the lines of equal stress; the line through A is blue.
The Contours view after Analyze: colour bands from dark red under the rectangle to blue at the edges, a legend from 0.1 to 75 kPa with per cent of q, the point A and the dashed line of the profile depth.
Contours after Analyze.
The Profile view after Analyze: the curve of the stress increase rising from zero at the surface to about 12.7 kPa near 2.6 m and then falling, with the point A at 10.9 kPa and a dashed line at z = 4.00 m.
Profile after Analyze.
The 3D view after Analyze: the loaded rectangle with red arrows on the ground, the axes x, y and z, the distances x = 2.50, y = −1.00 and z = 4.00 to the point A, and an element at A with the stress Δσz = 10.9 on it.
3D after Analyze.

The Show chips

Above the Section and the Contours drawings a bar has two chips: Lines of equal stress and Dimensions. In the Section view the lines chip is off and greyed out until you press Analyze, and then turns on; in Contours it is greyed out before Analyze too, and off by default afterwards, so that the lines can be laid over the colours. Dimensions is on by default in both. The Profile and 3D views have no chips.

Dragging on the drawing

Before Analyze two lines under the Section drawing read: “Drag a load to move it, the rings at its edges to resize it. Drag the dashed line to set the depth of the profile (zmax).” and “Drag the point A to place it. The stress and the lines of equal stress appear after Analyze.” After Analyze the first line is reduced to “Drag the dashed line to set the depth of the profile (zmax).” What each pull does, as the module runs it:

  • The rectangle in the Section and Contours views. Drag its body to move it along x: xc follows the pointer. Pulling the example rectangle 2 m to the right changes xc from 0 to 2. The section shows one plane, so the pull does not change yc.
  • An edge ring in the Section and Contours views. The rings at the two ends change L: the edge you pull follows the pointer and the other edge stays where it is, so L and xc change together. Pulling the right ring 1 m to the right gives L = 4 and xc = 0.5; pulling the left ring 1 m to the left gives L = 4 and xc = −0.5. The side stops at 0.1 m: pulling the left ring far to the right leaves L = 0.1 with the right edge where it was.
  • The rectangle in the 3D view. Drag it over the ground to move it in both directions: a pull of the example changed xc to 1.15 and yc to 0.3. Four rings sit on the edges: the two along x change L and xc as above, the two along y change B and yc in the same way. B is changed by dragging in the 3D view, not in the Section view.
  • Rectangles never overlap. A pull that would put a rectangle on another stops at the last free place, and a message says “That would put rectangular load 1 and rectangular load 2 on top of one another — the value is kept as it was.” Pulling a second rectangle at xc = 5 onto the first stopped at xc = 3, where the two meet at a side.
  • The point A. Drag the blue point in the Section or Contours view: x and z follow the pointer in steps of 5 cm, and y is not changed. The depth stops at 0.05 m at the top and at the foot of the drawn frame at the bottom, and x at the sides of the frame. With the example, pulling A far to the upper left gave x = −4.8 m and z = 0.05 m, and far to the lower right x = 4.8 m and z = 9 m. The 3D view has no handle for A; type its coordinates.
  • The dashed line (Section and Contours). Drag it up or down to set zmax; it stops at 0.5 m.
  • After Analyze the rectangles are locked: their body and rings are gone from the drawing. The point A and the dashed line stay free, and so do the boxes x, y, z and zmax; dragging A after Analyze updates the stress at once (from the example, dragging A to x = 1.5 m, z = 5 m gave 12.01 kPa).

The 3D view has its own hint, “Drag a load over the ground to move it, the rings at its edges to resize it.” These pulls work before Analyze only.

Zoom

Each view has −, a percentage and + at the lower right, and a button that fits the whole drawing in the pane. Zoom is a property of the drawing only: it is not saved with the model and does not change the report.

Entering the model, section by section

The Model tab has four sections: Model data, Rectangular loads, Point A and Depth profile. Each opens when you click its title; Next and Back at the foot walk you through them, and Analyze waits below the last one. Where a unit is shown twice or three times, such as m · ft, the units are those of SI · kN, SI · tf and US in turn, and equal ones are merged. Defaults are shown in SI; in US the boxes show the converted values, for example 9.84252 ft for the 3 m side and 3.13282 ksf for the 150 kPa load.

Model data

The first section holds the model name, Save to file…, Open file…, Quick Save… with its list and Load and Delete, and Reset to defaults. It works as described in the workspace guide. Reset to defaults puts the example back at once, whatever you had typed.

The Model data section with the model name, Save to file, Open file, Quick Save, Reset to defaults and the quick-save list with Load and Delete.
Model data.

Rectangular loads

The section is a form over a table. The New rectangular load form takes q, L, B, xc and yc; + Add rectangular load puts the rectangle into the Rectangular loads table, and a counter beside the button shows how many of the eight there are. The table lists each rectangle with its load, sides and centre. Press a row to change that rectangle in the form (the form then reads Editing · Rectangular load 1 and offers Done and Delete rectangular load; the note says that changes apply as they are entered), or press × to take a rectangle out. The first rectangle is already in the table when the module opens, and Delete rectangular load and × are greyed out while it is the only one.

The Rectangular loads section: the New rectangular load form with q = 150 kPa, L = 3 m, B = 2 m, xc = 5 m and yc = 0 m, the Add rectangular load button with the counter 1 of 8, and the table with Rectangular load 1.
Rectangular loads: the form over the table.
Rectangular load fields (the form, and each row of the table)
FieldUnitDefault
Load per unit area q
The uniform pressure of the rectangle on the ground. Zero or more.
kPa · t/m² · ksf150
Side of the rectangle along x L
At least 0.001 m.
m · ft3
Side of the rectangle along y B
At least 0.001 m.
m · ft2
Position of the centre along x xc
Any value. The first rectangle has 0; the New rectangular load form opens with 5.
m · ft0
Position of the centre along y yc
Any value.
m · ft0
The Rectangular loads section with the row of rectangle 1 pressed: the form reads Editing, Rectangular load 1, shows q, L, B, xc and yc with the Done and Delete rectangular load buttons.
A row of the table pressed: the rectangle is edited in the form.

The rectangles may not lie on top of one another: two rectangles may meet at a side but not overlap. Adding or editing a rectangle that would overlap another is refused (see Messages). The rectangles are listed in the order you add them, and their numbers name the results “From rectangular load 1”, “From rectangular load 2” and so on. The sides stay along x and y: the module does not turn a rectangle.

The Rectangular loads section with two rectangles in the table: Rectangular load 1 with q = 150 kPa, L = 3 m, B = 2 m and centre (0, 0), and Rectangular load 2 with q = 75 kPa, L = 3 m, B = 2 m and centre (5, 0); the counter reads 2 of 8.
Two rectangles in the table.

Point A

The three coordinates of the point where you want the stress. A is under the ground surface at the position (x, y) in plan and the depth z. It may be under a rectangle, on its edge or outside it; the corner method handles all of these.

The Point A section with x = 2.5 m, y = −1 m and the depth z = 4 m.
Point A.
Point A fields
FieldUnitDefault
Point A: x on the ground surface x
In the same coordinates as the centres. For one rectangle centred at the origin it is measured from the centre.
m · ft2.5
Point A: y on the ground surface y
In the same coordinates. The Section view is the plane through this value of y.
m · ft−1
Depth of the point A z
At least 0.001 m below the ground surface.
m · ft4

Depth profile

The depth down to which the table of the stress under A and the Profile view run. The table goes down to zmax, or to the depth of A if that is deeper; the Profile view goes to zmax, or to 1.2 times the depth of A if that is deeper.

The Depth profile section with the depth of the profile zmax = 12 m.
Depth profile.
Depth profile field
FieldUnitDefault
Depth of the profile zmax
At least 0.1 m. The table goes down to this depth, or to the depth of A if that is deeper; the Profile view goes to this depth, or to 1.2 times the depth of A if that is deeper.
m · ft12

Several rectangles and how they combine

The one choice in the module is how many rectangles there are, from 1 to 8; you make it by adding or deleting rectangles. The stress of each rectangle is found as if it were alone, from the position of A relative to its four corners, and the stresses are added. This works because the ground is elastic, so the stresses of separate loads add.

  • Positions are on one set of axes. x, y and every xc, yc are in the same coordinates. Moving a rectangle and A together by the same distance changes nothing: the example with the centre at (4, 3) and A at (6.5, 2) gives 10.90 kPa, the same as the example.
  • Loads can differ. Each rectangle has its own q, L and B, so a heavy core and a lighter surround can be put in one model.
  • The result lists the parts. The Results tab shows the total and the part from each rectangle, and the Calculations tab writes out each rectangle’s working.
  • The sides are fixed to the axes. To model a rectangle that is turned, or an irregular shape, use Influence chart.

With the example rectangle (150 kPa, 3 m × 2 m, at the origin) and A at x = 2.5 m, y = −1 m, z = 4 m, a second rectangle of the same size centred at xc = 5 m is the mirror image of the first about A, so it adds the same 10.90 kPa: 21.79 kPa in all. If the second is 75 kPa, it adds 5.448 kPa and the total is 16.34 kPa. A third rectangle of 150 kPa centred at 10 m brings the total of the three to 22.45 kPa.

The Section view of two rectangles, q1 = 150 kPa and q2 = 75 kPa, with the lines of equal stress of the sum, labelled 30, 20, 16, 10 and 7, and the point A with the label Δσz = 16.34 kPa.
Two rectangles, 150 kPa and 75 kPa: the lines of equal stress of the sum.
The Contours view of the same two rectangles: the colour bands of the sum, with lower stress in the gap between the rectangles near the surface.
The same two rectangles in the Contours view.

Rectangles that meet

Two rectangles that meet at a side give the same as one rectangle made of both. The example rectangle with a second one of 150 kPa and 3 m × 2 m centred at xc = 3 m meets it at the side x = 1.5 m; the parts are 10.90 kPa and 19.73 kPa and the total 30.63 kPa. One rectangle L = 6 m, B = 2 m centred at xc = 1.5 m gives 30.63 kPa, the same. Likewise a second rectangle meeting along y (centred at yc = 2 m) gives 16.18 kPa, and one rectangle L = 3 m, B = 4 m centred at yc = 1 m gives 16.18 kPa. An L-shaped or stepped load can therefore be built from rectangles that meet at their sides.

Which should I use?

  • One rectangle or several? One when the pressure is uniform over a rectangle; several when the pressure differs from part to part, or when the shape is made of rectangles.
  • A load much longer than wide is close to a strip: with L = 30 m the example gives 41.14 kPa; Vertical strip load is the plane-strain model.
  • A round load is not a rectangle: use Circle, any point.

Analyze and read the results

Press Analyze. The bar changes to Analysed — the stress at the point calculated and says “The inputs are locked. Edit inputs clears the results; the unit system can still be changed. The point A stays free: drag it on the drawing or change its coordinates, and the stress there is calculated at once.” A message appears briefly, “Analysed — see the Results tab and the Calculations.” The module stays on the Model tab: open Results for the answer. The Section view now shows the lines of equal stress.

The Analysed bar: Analysed — the stress at the point calculated, the message about the locked inputs and the free point A, the Warnings (0) button and the Edit inputs button.
The bar after Analyze.
The Results tab: the cards Vertical stress increase at A 10.90 kPa and Influence value 0.07264, with the note that the overburden pressure is not included.
The cards of the example.
CardSymbolThe example
Vertical stress increase at AΔσz10.90 kPa
Influence value (one rectangle)Δσz/q0.07264
From rectangular load k (several rectangles)Δσz(k)the part of the total from rectangle k

Below the cards the Vertical stress increase under A table gives z, Δσz and, for one rectangle, Δσz/q at ten equal steps from the surface to zmax, with the row of A inserted and highlighted. With several rectangles the ratio column is left out. A Values, step by step table above it lists the steps of the Calculations tab with their values.

The table Vertical stress increase under A with the columns z, Δσz and Δσz/q: 1.200 m 7.668 kPa, 2.400 m 12.59 kPa, then 4.000 m 10.90 kPa 0.07264 highlighted, and on to 12.00 m with 2.603 kPa and 0.01735.
The depth table of the example.
The Results tab of two rectangles: the total 16.34 kPa and the parts 10.90 kPa from rectangular load 1 and 5.448 kPa from rectangular load 2.
Two rectangles: the total and the part from each.

Reading the table

A point beside the loaded area does not have its largest stress at the surface. In the example A lies 1 m outside the short side of the rectangle, and the table rises from 7.668 kPa at 1.2 m to 12.59 kPa at 2.4 m before falling to 10.90 kPa at 4 m and 2.603 kPa at 12 m; the Profile view shows the same bulge. Under the rectangle the stress is largest at the surface and falls with depth: under the centre of the example, 116.2 kPa at 1 m, 22.98 kPa at 4 m and 1.067 kPa at 20 m.

Using the numbers

  • The result is an increase, not the total stress: add the overburden pressure of the soil above A for the total vertical stress.
  • The influence value Δσz/q is the part of the surface pressure that reaches A. It is 1 at the surface under the rectangle, 0 beside it, and falls with depth and with distance.
  • Values are rounded where they are drawn, so the last digit of a figure on the drawing can differ by one from the card.
  • Change x, y or z after Analyze and everything follows at once; to change a rectangle, press Edit inputs, which unlocks the rectangles and clears the results.
  • Changing the unit system after Analyze re-states the cards and the report without a new run. The drawings keep their labels in m and kPa.

Warnings and notes

The bar carries a Warnings (0) button. It opens a window that says “No warnings — the assumptions of the solution hold for these inputs.” The runs of this manual, from the example to eight rectangles, gave no warning.

The window Warnings (0) with the text No warnings — the assumptions of the solution hold for these inputs, and a Close button.
The Warnings window.

The Calculations tab, the report and the Theory tab

The Calculations tab opens with Given and what is sought and then writes out the working in numbered steps, ending with the answer. For one rectangle:

  1. Corner rectangles — the equation for Δσz as a signed sum of I3, with m = |a|/z and n = |b|/z, and the equation of I3.
  2. I3 of each corner rectangle — one line for each of the four corners of the loaded area, with the distances a and b from A, m, n, I3 and the sign. A corner level with A in one direction gives zero.
  3. Sum — the signed sum, Δσz = sum × q. When A is below the centre, a second result for the centre of a rectangle is given as a check.
  4. Stress increase against depth — the same sum down the vertical line through A, as the table of the Results tab, with the row of A marked.

With several rectangles there is one step for each rectangle, with its four corners, then a Superposition step that adds the parts, then the depth table.

The Calculations tab: the Given and what is sought block with q = 150.00 kPa, the rectangle 3.00 (x) × 2.00 (y) m centred on the origin, the point A at x = 2.50, y = −1.00, z = 4.00 m, and the quantity sought.
The Calculations tab: the given data.
The Calculations tab: step 2, the four corner lines with m, n, I3 and the sign (two of them zero), and step 3, the sum 0.07264 and Δσz = 0.07264 × 150.00 = 10.90 kPa.
The Calculations tab: the corner rectangles and the sum.

The report

In the Report tab fill in the cover (project, location, client, report number, date, prepared by, title or qualification, checked by, and optional notes). The details are kept in this browser and saved with the model file. Save as PDF and Download Word (.docx) produce the summary report; the preview below the buttons is the report itself.

The report has six parts: 1 Introduction and scope, 2 Input data, 3 Calculation, 4 Results, 5 Summary and 6 References. It carries three drawings, the Section with the lines of equal stress, the Profile and the 3D view, and states the units used.

The Report tab: the cover form with project, location, client, report number, date, prepared by, title and checked by, the notes box, the Save as PDF and Download Word buttons, and the cover page of the report with the stress 10.90 kPa and the conclusion sentence.
The Report tab: the cover details, the two buttons and the first page.

The Theory tab

The Theory tab has five sections: Scope and assumptions, Below a corner, Any point and the centre, Worked example and References. Each opens when you click its title (Open all and Close all open or close them together), and the figures in it are computed from the equations.

Worked example: the module’s own example

The module opens on this example, so you can follow the numbers on your own screen.

Inputs of the example
SectionInputValue
Rectangular loadsRectangular load 1q = 150 kPa; L = 3 m; B = 2 m; centre (0, 0)
Point APosition and depthx = 2.5 m; y = −1 m; z = 4 m
Depth profileDepthzmax = 12 m

Step 1: the corners seen from A

The rectangle runs from x = −1.5 to 1.5 and y = −1 to 1. A is at (2.5, −1), so A is level with the lower long side. Taking each corner of the rectangle in turn, the distances a (along x) and b (along y) from A to the corner are: corner (1.5, 1), a = −1 and b = 2; corner (−1.5, 1), a = −4 and b = 2; the two corners at y = −1 have b = 0, so their rectangles have no area and give zero.

Step 2: the influence factors

With z = 4 m, m = |a|/z and n = |b|/z. Corner (1.5, 1): m = 0.25, n = 0.5, I3 = 0.04753, subtracted. Corner (−1.5, 1): m = 1, n = 0.5, I3 = 0.12018, added. For this second corner the equation gives 2mn√(m² + n² + 1) = 1.5, the fraction 1.5/2.5 × 3.25/2.25 = 0.8667 and the arctangent of 1.5/2.0 = 0.6435, so I3 = (0.8667 + 0.6435)/4π = 0.12018.

Step 3: the stress

Σ ± I3 = 0.12018 − 0.04753 = 0.07264, Δσz = 0.07264 × 150 = 10.90 kPa

The difference of the rounded factors is 0.07265; the module carries the unrounded values and shows 0.07264. These are the two cards of the Results tab and the steps of the Calculations tab. An independent numerical integration of the point-load solution over the rectangle gives the same 10.90 kPa, and the same integration at 1.2 m, 2.4 m and 12 m reproduces the table (7.668, 12.59 and 2.603 kPa).

Other points under the same rectangle

The same rectangle at z = 4 m: A below the centre gives 22.98 kPa (influence value 0.1532, four equal corner factors of 0.03830); A under a corner, at (1.5, 1), gives 16.06 kPa; A under the middle of a short side, at (1.5, 0), gives 18.08 kPa; A far away, at (10, 0), gives 0.2043 kPa. A 2 m square loaded with 150 kPa gives, below its centre at 1 m, 105.1 kPa, an influence value of 0.7009, the value for a point at a depth of half the side below the centre of a square (4 × I3(1, 1)).

Other unit systems

The same rectangle in SI · tf, with q = 15 t/m² (the other values unchanged), gives 1.090 t/m² and the influence value 0.07264. In US the default example, which is 3.13282 ksf on a rectangle 9.84252 ft by 6.56168 ft, gives 0.2276 ksf: 10.90 kPa is 0.2276 ksf. A check with round US numbers, q = 3 ksf, L = 10 ft, B = 6 ft, centred at the origin, A at x = 8 ft, y = −3 ft, z = 12 ft: the same independent integration gives 0.2266 ksf and an influence value of 0.07554, and the module gives 0.2266 ksf and 0.07554.

How each input changes the answer

Each row changes one thing in the example (one rectangle of q = 150 kPa, L = 3 m, B = 2 m centred at the origin, A at x = 2.5 m, y = −1 m, z = 4 m) and runs the module again, in SI · kN; where a row says two things, both change. The numbers are the ones the module gives, so you can reproduce any row; an independent numerical integration of the point-load solution over the rectangle agrees with every row to the digits shown.

The example with one change at a time
ChangeΔσz (kPa)Δσz/q
The example10.900.07264
q = 300 kPa
The stress is proportional to the load; the ratio is unchanged
21.790.07264
q = 75 kPa
Half the load, half the stress
5.4480.07264
L = 6 m
A longer rectangle puts more on A
23.140.1543
L = 1.5 m
A shorter one puts less
5.2320.03488
L = 30 m
A very long rectangle, close to a strip; A is level with its long side
41.140.2742
B = 4 m
A wider rectangle: more of the load is near A
20.220.1348
B = 1 m
A narrower one
5.5540.03703
B = 30 m
A very wide rectangle
38.320.2555
L = B = 30 m
A is deep inside a large area: the ratio approaches 1
147.90.9857
L = 2, B = 3, A at (−1, 2.5)
Sides and point turned together: the same as the example
10.900.07264
x = 0, y = 0
Larger than below the middle of a short side (next row) or a corner
22.980.1532
x = 1.5 m, y = 0
Below the middle of a short side: between the centre and the corner
18.080.1205
x = 1.5 m, y = 1 m
Below a corner of the rectangle
16.060.1071
y = 0
A level with the middle of the long sides; A is closer to the middle
12.100.08068
y = +1 m
The same as y = −1 m: the rectangle is symmetric about y = 0
10.900.07264
x = −2.5 m
The same as x = +2.5 m
10.900.07264
x = 10 m, y = 0
Far from the rectangle the stress is a tiny part of the load
0.20430.001362
z = 1 m
Beside the rectangle the stress is small near the surface
5.8770.03918
z = 2 m
It rises with depth first
11.960.07977
z = 8 m
Then falls
5.0280.03352
z = 20 m
The stress keeps falling with depth
1.0210.006806
z = 0.01 m
At the surface beside the rectangle the stress is almost zero
0.000014790.0000001
x = y = 0, z = 1 m
Below the centre near the surface the stress approaches q
116.20.7746
x = y = 0, z = 0.01 m
At the surface under the rectangle the stress equals q
150.01.000
xc = 4 m
A is then below a corner: the same as x = 1.5 m, y = 1 m
16.060.1071
Centre (4, 3), A at (6.5, 2)
Both moved by (4, 3): the same as the example
10.900.07264

Several rectangles, SI · kN, from the example (second rectangle added with the values shown):

Adding rectangles
AddedTotal (kPa)Parts (kPa)
Rectangle 2: 150 kPa, 3 m × 2 m, centre at (5, 0)
The mirror image of rectangle 1 about A
21.7910.90 + 10.90
Rectangle 2: 75 kPa, 3 m × 2 m, centre at (5, 0)16.3410.90 + 5.448
Rectangle 2: 150 kPa, 3 m × 2 m, centre at (3, 0)
Meets rectangle 1 at x = 1.5 m
30.6310.90 + 19.73
Rectangle 2: 150 kPa, 3 m × 2 m, centre at (0, 2)
Meets rectangle 1 at y = 1 m
16.1810.90 + 5.283
Rectangles 2 and 3: 150 kPa, 3 m × 2 m, centres at (5, 0) and (10, 0)22.4510.90 + 10.90 + 0.6619

The pattern follows the equations. The stress is proportional to q; it depends on the sides and the position of A only through their ratios to z, so doubling every length leaves the ratio unchanged; at the same depth it is larger below the centre than below an edge or a corner; and with z near zero it equals q under the rectangle and zero beside it. Because it is built from the four corner terms, the result does not change when the rectangle and A are moved together or turned together, as the rows “L = 2 m, B = 3 m …” and “Centre at (4, 3) m” show. The depth of the profile zmax changes the table and the Profile view but not the stress at A: 10.90 kPa with zmax = 6 m and 10.90 kPa with zmax = 0.5 m, a depth the module extends to the depth of A in the table.

Messages: when the module stops, and what it notes

The module checks the numbers it needs before it calculates. When an input cannot be used, press Analyze and a window titled Cannot analyse — 1 input error (or 2 input errors …) lists each message and the box of the value is marked in red; nothing is calculated.

The window Cannot analyse, 1 input error: Side of rectangle 1 along x (L1) must be at least 0.001 m.
The window Analyze opens when a side is zero.
WhenMessage and what to do
L is 0“Side of rectangle 1 along x (L1) must be at least 0.001 m.” Enter a side of at least 0.001 m.
B is 0“Side of rectangle 1 along y (B1) must be at least 0.001 m.” Enter a side of at least 0.001 m.
L and B are 0The window reads 2 input errors and lists both messages.
q is negative“Load per unit area of rectangle 1 (q1) must be at least 0 kPa.” Enter zero or a positive load.
z is 0“Depth of the point A (z) must be at least 0.001 m.” Enter a depth of at least 0.001 m.
zmax is 0“Depth of the profile (zmax) must be at least 0.1 m.” Enter a depth of at least 0.1 m.
A box is empty“Side of rectangle 1 along x (L1) is missing.” (and the same for q, x, y, z and the centre). Fill the box; for a rectangle you may instead take it out.
A new rectangle would overlap anotherA message appears briefly: “The new rectangular load would lie on rectangular load 1 — they cannot overlap. Give it another position or width.” The rectangle is not added.

The messages use the numbered names of the rectangles, such as “rectangle 1” and “L1”, even when there is only one, and the limits in the units of the unit system chosen. When you type a position or a side into a rectangle already in the table, or drag it, and it would put two rectangles on one another, a message appears briefly: “That would put rectangular load 1 and rectangular load 2 on top of one another — the value is kept as it was.” and the value stays as it was. At eight rectangles + Add rectangular load is greyed out and the counter reads 8 of 8.

Notes and warnings

With every input inside its limits the module calculates, and the Warnings window reads “No warnings — the assumptions of the solution hold for these inputs.” A load of zero is accepted and gives 0 kPa, with the influence value unchanged at 0.07264 in the cards; in the depth table the ratio column shows a dash except in the row of A, the Section and Contours views draw no lines or legend values, and the Profile view is a zero line. Very large values are accepted too: with q = 1,000,000 kPa and a rectangle of 1000 m × 1000 m the module gives 1,000,000 kPa below its centre, an influence value of 1.000, and a rectangle with a side of 0.001 m gives 0.003431 kPa at the point of the example.

Good practice and common mistakes

  • Use the module for a flexible, uniformly loaded rectangle. The pressure is q over the whole area. A stiff footing distributes its pressure differently; the module gives the stress for the pressure you enter, and a total load divided by the area is q.
  • Enter a pressure, not a force. q is a load per unit area: a column load of 600 kN on a 3 m × 2 m footing is q = 100 kPa.
  • Mind the axes. L is always along x and B along y, and the Section view cuts the plane y = yA. To look at another cut, change y.
  • Do not overlap rectangles. They may meet at a side but not lie on one another; to describe a stepped load, split it into rectangles that meet.
  • Add the overburden. The result is the stress increase; for the total vertical stress add the soil weight above A.
  • Look at more than one depth. Beside a loaded area the stress first rises with depth and then falls, so a single depth can mislead; read the table or the Profile view.
  • Place A with the drawing, then type exact values. Dragging snaps to 5 cm; type the coordinates when you need a given place.
  • Check the units after switching the system: type values in the units shown beside the boxes.
  • Keep a record. The report is the record of an analysis; use Quick Save… or Save to file… to keep the model.

Frequently asked questions

How is the stress below a rectangular load calculated?

The module uses the closed-form integral of Boussinesq’s point-load solution over a rectangle, which gives the stress below one corner as Δσz = q I3. For any other point it adds and subtracts four rectangles that share a corner above A. For the module’s example it gives 10.90 kPa.

What is the influence value Δσz/q?

It is the stress increase divided by the pressure of the rectangle. It depends only on the sides and the position of A divided by the depth, is 1 at the surface under the rectangle, and is the number to use if you have a table of influence values. The module gives it for one rectangle; with several rectangles it gives the stress of each.

Does the result include the weight of the soil?

No. It is the increase caused by the rectangles only. Add the overburden pressure of the soil above A for the total vertical stress.

How many rectangles can I add, and can they overlap?

Up to eight, each with its own q, L, B and centre. They may meet at a side but not overlap; the module refuses a rectangle that would lie on another. The stresses add.

Can I turn a rectangle?

The sides of every rectangle are along x and y. Turn the whole model instead: choose the axes along the sides, and place A in the same axes. For a rectangle at another angle, or an irregular shape, use Influence chart.

Can I drag the rectangle and the point on the drawing?

Yes, before Analyze. In the Section or Contours view drag the rectangle along x and the rings at its ends to change L; in the 3D view drag it over the ground and use all four rings to change L and B. Drag the blue point to place A and the dashed line to set the depth of the profile. After Analyze the rectangles are locked, but A and the dashed line stay free.

What does the Section view show when A is not on the rectangle?

The plane through A parallel to the x axis. A red note under the ground line says whether the plane cuts the load (“the section cuts the loaded area”) or not (“the loaded area lies beside this section (y outside the rectangle)”). With several rectangles, one the plane misses is drawn dashed with its distance, such as “6.00 m beside the plane”, and still acts on the section from beside. The point A stays on that plane, so moving A in y moves the plane.

What values does the module accept?

q zero or more, L and B at least 0.001 m, z at least 0.001 m, zmax at least 0.1 m, and x, y, xc and yc any value. Anything else stops the analysis with a message that names the value.

Which units does it use, and what are the units of the answer?

SI · kN, SI · tf or US, switchable in the header at any time, even after Analyze. Stresses are in kPa, t/m² or ksf and lengths in m or ft. The default example gives 10.90 kPa, 1.090 t/m² with q = 15 t/m², or 0.2276 ksf.

What does the report contain?

A cover with your project details and the answer, then six parts: introduction and scope, input data, the calculation step by step, results, summary and references, with the section, profile and 3D drawings. It is saved as a PDF or a Word file once the model is analysed.

Does the module remember my inputs?

Yes. Every change is kept in the browser, and the page opens again on the model you last worked on. It also reopens in the analysed state if nothing was changed after Analyze; after moving A or the profile depth, press Analyze again. Reset to defaults brings back the example at once; Save to file and Quick Save keep copies.

When is a rectangle the wrong model?

When the load is round (use Circle, any point), long and narrow compared with the depth you ask about (use Vertical strip load), of an irregular shape (use Influence chart), or on layered ground with a stiff layer that spreads the load (use Westergaard areas).