Skip to the manual
GeoTerva Free for 7 days

Retaining walls: the user manuals

Three modules check a retaining wall for stability and bearing, in the static case and in an earthquake: a reinforced-concrete cantilever wall, a gravity wall and a reinforced-soil wall. This page helps you choose the module that matches your wall and links to the manual of each.

Updated 20 October 2026 · GeoTerva user manual

Which retaining wall module do I need?

The Retaining Walls family has three modules. All of them check a wall against sliding, overturning and bearing, in the static case and in an earthquake. They differ in the kind of wall. Pick the one that matches the wall you are designing.

Your wallModule
A reinforced-concrete wall with a stem, a toe and a heel, with an optional shear key or pressure-relief shelf; stability, bearing and the actions in the stem and the slabsCantilever RC wall
A stone masonry or plain concrete wall that holds by its own weight, on a stepped footingGravity wall
A wall of granular fill reinforced by strips, geotextile or geogrid behind a facing; the tension of every level, rupture, pullout and the stability of the blockMSE wall

The three manuals

Each manual follows the same plan: what the module calculates, what you need before you start, a quick start, the screen, every input section by section, the choices that decide the margin, the results, the report, a worked example you can reproduce, a table of how each input changes the answer, the messages the module gives, and answers to common questions.

What the three modules share

  • The workspace. The drawing, the tabs, Analyze and the input lock, units and the report follow the same layout as the other GeoTerva modules. See the workspace guide.
  • Static and seismic cases. Each module checks the wall under its own weight, the soil, the water and the surcharges, and again in an earthquake.
  • The stability checks. Sliding, overturning, eccentricity and bearing, each against its required factor.
  • Earth pressure. The pressure behind the wall follows the methods of the Lateral earth pressure manuals.
  • Surcharges. Loads on the retained ground add to the pressure; see the Surcharge loads manuals.

What each module takes, side by side

ModuleWallAlso gives
Cantilever RC wallReinforced concrete, stem, toe, heel, key, shelfShear and moment in the stem and the slabs
Gravity wallStone masonry or plain concrete, stepped footingEvery force in a ledger
MSE wallReinforced granular fill behind a facingTension, rupture and pullout of every level

A typical wall check in order

  1. Choose the module

    Pick the one that matches the wall and open its manual for the fields.

  2. Draw the wall

    Enter the dimensions of the wall, or of the reinforced block.

  3. Describe the soil and the loads

    Enter the backfill and the foundation soil, the water, the surcharges and the earthquake.

  4. Analyze and read the checks

    Press Analyze. Read the factors of safety, the bearing pressure and the actions, then save a report with the cover filled in.

Frequently asked questions

How do I check a retaining wall with GeoTerva?

Open the module for the wall: Cantilever RC wall, Gravity wall or MSE wall. Draw the wall, enter the soil, the water, the surcharges and the earthquake, press Analyze, and read the factors of safety for sliding, overturning and bearing.

Which module do I use for a reinforced-soil wall?

MSE wall. It checks the tension, the rupture and the pullout of every reinforcement level and the stability of the reinforced block.

Do the modules include an earthquake?

Yes. Each module checks the wall in the static case and in the seismic case.

Where do the earth pressures come from?

From the methods described in the Lateral earth pressure manuals, such as Rankine, Coulomb and Mononobe–Okabe, depending on the module.

Do the cantilever and gravity modules give the forces in the wall?

The cantilever module gives the shear and moment in the stem and the slabs. The gravity module lists every force in a ledger.