Skip to the manual
GeoTerva Free for 7 days

Braced cut in clay: user manual

Design the bracing of a strutted excavation in undrained clay: the apparent-pressure envelope chosen from the stability number, the load of every strut, the sheeting, the wales and the struts to EN 1993-1-1 or AISC 360-22, the tension crack at the first strut and the bottom heave of the base. This manual walks through the screen, every input, the results and every message, with a worked example you can reproduce.

Updated 20 October 2026 · GeoTerva user manual

What the module calculates

Braced cut in clay designs the bracing of a strutted excavation in undrained clay. You give the depth of the cut, the clay and the levels of the struts; the module draws the apparent-pressure envelope that Peck derived from measured strut loads, works out the load of every strut, and sizes and verifies the sheeting, the wales and the struts to EN 1993-1-1 or AISC 360-22. It also checks the first strut against the tension crack and the base of the cut against bottom heave.

The clay is analysed in total stress, with the unit weight γ and the undrained shear strength cu. The shape of the envelope is chosen by the stability number γH/cu, with H the depth of the cut:

γH/cu > 4: σa = max( γH − 4cu, 0.3 γH ) γH/cu ≤ 4: σa = k γH, k = 0.2 to 0.4
  • Above 4 the clay is soft to medium: the envelope is zero at the surface, rises over the top quarter of the depth and keeps its plateau σa to the base; its resultant is 0.875 σa H.
  • At or below 4 the clay is stiff: the envelope rises over the top quarter, keeps σa over the middle half and falls over the bottom quarter; its resultant is 0.75 σa H. The coefficient k is yours to set between 0.2 and 0.4 (0.3 by default).

For the default example, γH/cu = 18 × 7 / 35 = 3.60, so the stiff envelope applies with σa = 0.3 × 18 × 7 = 37.80 kPa and a resultant of 0.75 × 37.80 × 7 = 198.45 kN/m.

What you can describe

  • Clay layers: up to ten, each with its unit weight, saturated unit weight and cu; several layers inside the cut are thickness-averaged into one cu and one γ. The bottom layer runs on below the base.
  • The cut: depth H, width B, optional plan length L, embedment d of the sheeting below the base and the depth T of a hard stratum.
  • A water table behind the sheeting, and a uniform surcharge beside the cut.
  • Struts: from 2 to 15 levels at depths you type or drag, at a horizontal spacing s.
  • Members: sheeting by its section modulus; wale and strut either by the numbers a profile table prints or from the section catalogue.
  • The base check against bottom heave with its required factor of safety, and the hinge convention and the design code.

It draws the section and a 3D view, writes the working step by step, and prepares a PDF or Word report.

Which module for which cut

Before you start: what you need

Have these ready from your design and your ground investigation:

WhatWhere from, and notes
The clayBoring logs, vane or triaxial tests: unit weight, saturated unit weight and undrained shear strength cu (at least 1 kPa) of each layer, and the thickness of each layer except the last.
The cutYour design: depth H (at least 0.5 m), width B (at least 0.5 m), the plan length if the cut is short, the embedment d of the sheeting below the base, the depth to a hard stratum if there is one.
The strutsThe depth of each level below the ground surface, each strictly between the surface and the base, and the horizontal spacing s (at least 0.5 m).
The membersYield strength from the steel grade; the section modulus of the sheeting per metre of wall; for the wale a modulus (or a catalogue section); for the strut an area and a second moment of area (or a catalogue section).
Loads and waterA uniform surcharge beside the cut, if any; the depth of the water table if it matters for the unit weight.

Quick start in eight steps

  1. Open the module and choose the units

    Open Braced cut in clay from the Braced Cuts family. Pick SI · kN, SI · tf or US in the header; you can change it at any time.

  2. Enter the clay

    In Soil layers fill the New layer form and press + Add layer, once per layer from the top down; the last layer has no thickness.

  3. Describe the cut

    In Groundwater choose the water table; in Cut geometry type H, B, L, d and the hard stratum; in Surcharge add a uniform load if there is one.

  4. Place the struts

    In Struts type the spacing s and the depth of each level; + Add a strut level adds one. Before Analyze you can also drag a strut on the drawing.

  5. Give the members

    In Sections choose the steel grade and the section of the sheeting, the wale and the strut; in Base heave the required factor of safety; in Analysis settings the envelope coefficient, the hinge convention and the design code.

  6. Press Analyze

    Press Analyze in the bar at the foot of the Model tab. The bar reads Analysed and the model locks. The module stays on the Model tab: open Results.

  7. Read the answer

    The Results tab gives the drawings, the tables of the strut loads and the wales, and the cards: σa, Pmax , Mmax , Wreq , the utilisation of each member and the heave factor.

  8. Take the working and the report

    The Calculations tab writes out the steps with your numbers; the Report tab saves a PDF or a Word file.

The screen: section and 3D

The layout is the one every GeoTerva module shares, described in the workspace guide. The drawing has two views, chosen with the buttons above it:

  • Section is the cut with its clay, the sheeting, the struts lettered A, B, C … from the top, the dimensions and the hard stratum. After Analyze it adds the envelope with σa, the load of each strut (PA = 162.06 kN …) and Mmax marked on the sheeting; each is green where the member carries its force and red where it does not.
  • 3D is an oblique view of the excavation: the sheeting on both sides, the wales and the struts at their spacing, the clay on the front face, a legend with the steel grade and section of the members, and, after Analyze, the load of every strut level.
The Section view before Analyze: the cut with its clay, the sheeting, the struts A, B and C, the dimensions 1, 2.5, 2.5, 1, 7, 6, 1.5 and 4 and the hard stratum.
Section before Analyze.
The Section view after Analyze: the stiff-clay envelope with sigma a = 37.8 kPa, the strut loads 162.06, 271.26 and 162.06 kN and Mmax = 27.03 kN·m/m.
Section after Analyze: the envelope, the strut loads and the largest moment.
The 3D view after Analyze: the excavation, the sheeting with its wales and struts, the loads of the three strut levels and the legend with the sections.
3D after Analyze.

Dragging, and what is locked

Before Analyze the struts are the only things on the drawing that move: drag a strut up or down, and its depth in Struts follows, in steps of 0.05 m. A strut cannot be taken above 0.1 m, nor lower than 0.1 m above the base. Nothing else on the drawing is dragged: the layers, the water and the cut are changed in the Model tab. After Analyze the model is locked and nothing can be dragged.

There are no Show chips. Each view has −, a percentage and + at the lower right and a button that fits the whole drawing in the pane. The Model tab follows what you type: a value that cannot be used (a strut outside the cut, for example) is reported in the bar at the foot of the tab as Cannot be analysed, before you press Analyze.

Entering the model, section by section

The Model tab has nine sections: Model data, Soil layers, Groundwater, Cut geometry, Surcharge, Struts, Sections, Base heave and Analysis settings. Each opens when you click its title; Next and Back at the foot walk you through them, and Analyze waits in the bar below. A unit shown two or three times, such as m · ft, gives the units of SI · kN, SI · tf and US in turn. Defaults are shown in SI. After a switch of the unit system the boxes show the converted values, unrounded.

Model data

The first section holds the model name, Save to file…, Open file…, Quick Save… with its list, Load and Delete, and Reset to defaults. It works as described in the workspace guide. Its note says that the page opens every time on the default model, not analysed.

The Model data section with the model name, Save to file, Open file, Quick Save, Reset to defaults and the quick-save list with Load and Delete.
Model data.

Soil layers

A New layer form over a Soil layers table. Fill the form and press + Add layer: the layer goes to the bottom of the table, with a counter (1 of 10). Press a row to change it in the form; × takes it out. Every layer is undrained clay. Several layers inside the cut are thickness-averaged into one cu and one γ for the envelope, and the layer under the base carries the heave check. The bottom layer has no thickness (its row shows a dash): it runs on below the base, to the stratum.

The Soil layers section: the New layer form with thickness 5, unit weight 18, saturated unit weight 19 and undrained cohesion 35, the Add layer button with the counter 1 of 10 and the table with one layer Clay.
Soil layers: the form over the table.
Layer fields (the form, and each row of the table)
FieldDefaultWhat to enter
Name
—
automaticOptional; empty gives Clay, or Clay-1, Clay-2 … when there are several.
Thickness H
m · ft
5 (form)At least 0.1 m. Absent on the last layer.
Unit weight γ
kN/m³ · t/m³ · pcf
18At least 1 kN/m³. Used above the water table, or everywhere without one.
Saturated unit weight γsat
kN/m³ · t/m³ · pcf
19At least 1 kN/m³. Used below the water table.
Undrained cohesion cu
kPa · kg/cm² · psf
35At least 1 kPa.

Groundwater

Water table has Below the base (default) and Present. With Present, a box for the depth zw below the ground surface appears (3 m by default, at least 0). The clay envelopes are total-stress: the water is recorded but adds no separate pressure. Its effect is on the unit weight: below the table the clay weighs its saturated unit weight, so γ averaged over the cut rises (with zw = 2 m the example gives σa = 39.29 kPa instead of 37.80 kPa). The module notes that the cut has been computed undrained.

The Groundwater section with the buttons Below the base and Present.
Groundwater.

Cut geometry

The Cut geometry section with the buttons At a known depth and None within reach and the boxes H 7, B 6, L 20, d 1.5 and T 4.
Cut geometry.
Cut geometry
FieldDefaultWhat to enter
Depth of the cut H
m · ft
7At least 0.5 m. It fixes the envelope. The module notes when H is below about 6 m, the depth the envelopes were derived for.
Width of the cut B
m · ft
6At least 0.5 m. Feeds the heave check.
Plan length of the cut L
m · ft
20 (optional)At least 0.5 m. Empty means a long cut: the shape term of the heave check is 1.
Wall embedment below the base d
m · ft
1.50 or more. Drawn, but not credited in the heave check.
Base to hard stratum T
m · ft
4Shown when a hard stratum is At a known depth (the default); None within reach hides it.

Surcharge

The section is the one of the braced-cut family: a New load form (the kind Uniform; Strip and Point stand there marked Soon and the kind stays Uniform) and a table of the loads. Type the intensity q (10 kPa in the form) and press + Add load: the table shows it as a uniform load over the whole surface. One load at most; press × to take it away. The opening model has none. A surcharge is not put inside the envelope; it is added beside it as its own uniform lateral pressure Δpq = q (clay, φ = 0, so Ka = 1) over the full height of the cut, and the struts, the sheeting and the wales all see it. It enters the heave check and the tension-crack depth as well.

The Surcharge section with the New load form, the Uniform kind, the intensity 10 kPa and the Add load button.
Surcharge.

Struts

The horizontal spacing s (3 m, at least 0.5 m) and one block per strut, Strut 1, Strut 2 …, each with its depth below the ground surface: zA = 1 m, zB = 3.5 m and zC = 6 m in the example. + Add a strut level and Remove the last strut change the number, from 2 to 15 (the counter reads 3 of 15). The levels are lettered A, B, C … from the top in the order of their depth. At least two struts are needed; each must lie strictly between the surface and the base.

The Struts section with the spacing 3 and the blocks Strut 1, 2 and 3 with depths 1, 3.5 and 6, the Add a strut level and Remove the last strut buttons and the counter 3 of 15.
Struts.

Sections

Three blocks, Sheeting, Wale (waling beam) and Strut. Each has a steel grade: S235, S275 (default), S355, or Typed. The yield strength fy follows the grade (275 000 kPa for S275, with the chip “from the grade”) until you type a value of your own; it must be at least 100 000 kPa.

  • Sheeting: Section modulus given says which catalogue column the value is, Elastic Wel (default) or Plastic Wpl; W per metre of wall (600 cm³/m).
  • Wale: How the section is given, By its modulus W (default; W = 1 000 cm³, elastic or plastic) or From the catalogue, where a section type (IPE, HEA, HEB, HEM, UPN or a steel box with its width, depth and wall thickness) and a section are chosen; the catalogue gives the class and the shear area.
  • Strut: By A and I (default; the area A = 65.7 cm², the second moment of area about the weak axis Imin = 3 598 cm⁴ and, with EN 1993-1-1, the buckling curve, default c) or From the catalogue (tube, square or rectangular tube, IPE, HEA, HEB, HEM or UPN). Then the buckling length Lb (it follows the width of the cut, 6 m, until you type another), the effective length factor K (1) and the modulus of elasticity E (210 000 000 kPa, from the design code).
The Sections section: the Sheeting block with the steel grade S275, the Elastic Wel and Plastic Wpl buttons, yield strength 275000 from the grade and section modulus 600, then the Wale block with the grade and the choice By its modulus W or From the catalogue.
Sections: the first two blocks.

Base heave

Check the base against bottom heave has Yes (default) and No. With Yes, give the required factor of safety FSreq (1.5, from 1 to 3). With No the base is not checked and the card is absent. The check compares the resistance of the clay under the base with the weight of the soil beside the cut: see Bottom heave.

The Base heave section with the buttons Yes and No and the required factor of safety 1.5.
Base heave.

Analysis settings

The stiff-clay envelope coefficient k (0.3; 0.2 to 0.4) is used when γH/cu is 4 or less. Hinge convention has Auto (default), Interior struts, All but the top and Every strut: see Strut loads. Verify the steelwork to has EN 1993-1-1 (Eurocode 3), with the partial factor γF on the bracing loads (1.35, from 1 to 1.6) and γM0 (1) and γM1 (1) from 1 to 1.3 on the cross-section and the buckling resistance, or AISC 360-22, with LRFD (the load factor γH on the earth pressure, 1.6, from 1 to 2) or ASD.

The Analysis settings section with the stiff-clay envelope coefficient 0.3, the hinge convention buttons, the design code buttons and the partial factors 1.35, 1 and 1.
Analysis settings.

The envelope: soft to medium, or stiff

The module takes γ and cu (averaged over the depth when there are several layers, and γ weighted with the saturated unit weight below the water table), forms γH/cu and picks the envelope. The plateau pressure σa is the first card.

Soft to medium: γH/c above 4

With cu = 20 kPa the number is 18 × 7 / 20 = 6.3. Then γH − 4cu = 126 − 80 = 46 kPa against 0.3γH = 37.8 kPa, and the larger governs: σa = 46.00 kPa. The resultant is 0.875 × 46 × 7 = 281.75 kN/m, against 198.45 kN/m for the stiff example: a weaker clay loads the struts more, and the module gives Pmax = 338.1 kN (271.3 kN with cu = 35 kPa).

The Section view of the cut with c = 20 kPa after Analyze: the soft-to-medium envelope, zero at the surface and constant from the top quarter to the base, sigma a = 46 kPa.
The soft-to-medium envelope: zero at the surface, a plateau from the top quarter to the base.

Stiff: γH/c at most 4

σa = k γH. With k = 0.3 the example gives 37.80 kPa; k = 0.4 gives 50.40 kPa (Pmax = 361.6 kN) and k = 0.2 gives 25.20 kPa (Pmax = 180.8 kN): the loads follow k in proportion. Choose k from the stiffness of the clay; 0.3 is the average of the range.

Near the changeover

At γH/cu = 4 the plateau σa is the same on both sides (0.3γH = 37.8 kPa in the example), but the shapes differ: the soft-to-medium envelope keeps its plateau to the base and has a resultant a sixth larger than the stiff one. The runs show it: cu = 31.5 kPa (ratio 4.00, stiff) gives 271.3 kN for the largest strut and cu = 28 kPa (ratio 4.5, soft to medium) gives 277.8 kN, with the same σa = 37.80 kPa. When γH/cu is between 3.6 and 4.4 the module adds a note that gives the resultant of the branch used and of the other (198.45 and 231.53 kN/m in the example) and advises you to check cu against the tests and, where it is uncertain, to run the other branch and design for the heavier. The default example sits in this band (3.60), so its first note is this one.

Several clay layers, a water table, a surcharge

  • Several layers: cu and γ are averaged over the depth of the cut with the thicknesses as weights. Two layers, 3 m with cu = 25 kPa over the rest with cu = 45 kPa, average to (25 × 3 + 45 × 4) / 7 = 36.43 kPa; with γ = 18 the ratio is 3.46 and σa = 37.80 kPa.
  • A water table at 2 m raises the weight of the clay below it to γsat: the average γ is 18.7 kN/m³, the ratio 3.74 and σa = 39.29 kPa.
  • A surcharge of 20 kPa does not change σa (37.80 kPa): it adds 20 kPa over the 7 m of the cut, 140 kN/m, to the 198.45 kN/m of the envelope. See Strut loads.

Strut loads, sheeting and wales

From the envelope to the strut loads

The sheeting is idealised as hinged at the struts, and each piece between hinges is a determinate beam carrying its share of the envelope. A reaction R per metre of wall comes out at each strut level, and the strut load is P = R × s. A strut at a hinge collects a reaction from the pieces on both sides. The hinge convention says where the hinges are:

  • Interior struts: hinges at every strut except the top and the bottom ones, the classical arrangement.
  • All but the top and Every strut: hinges at more levels, which share the load differently (for the example, Pmax = 275.6 and 279.9 kN against 271.3 kN).
  • Auto (default) takes Interior struts and switches to another convention if that layout would put a strut in tension; the module then says so in a note. The example has the same figures with Auto and with Interior struts.

For the example the two pieces (0 to 3.5 m and 3.5 to 7 m) each carry 99.23 kN/m. Piece 1 is an overhanging beam on A and B: RB = 99.23 × (2.1389 − 1.00) / 2.50 = 45.21 kN/m and RA = 99.23 − 45.21 = 54.02 kN/m. Level B collects 45.21 from each side, 90.42 kN/m, so PA = PC = 54.02 × 3 = 162.1 kN and PB = 90.42 × 3 = 271.3 kN; the module gives 271.3 kN as the largest.

The sheeting and the wales

The largest moment of the sheeting is the largest anywhere in the pieces: 27.03 kN·m/m in the example, at 2.30 m, in piece 1. Each wale is a simple span s loaded by the reaction of its level: Mwale = R s² / 8 = 90.42 × 3.00² / 8 = 101.72 kN·m at level B. The first card block gives Mmax and the sheeting modulus, and under the cards stand the moment and the modulus of the governing wale.

What the strut layout does

  • Spacing: with s = 4 m the largest strut load is 361.7 kN and the wale utilisation 0.8878; with s = 2 m, 180.8 kN and 0.2219. The wale moment goes with s², the strut load with s; the sheeting is not affected.
  • Number of struts: four struts at 1, 2.5, 4 and 5.5 m bring Pmax to 180.3 kN and Mmax to 12.15 kN·m/m.
  • Depth of the cut: at H = 9 m (struts unchanged) the ratio is 4.63, the soft-to-medium envelope gives σa = 48.60 kPa, and the lowest strut carries 882.1 kN. The module warns that Strut C carries 882.09 kN, 2.3 × the average of the 3 struts and suggests moving the struts so that the tributary heights are similar, or adding a level.
  • A strut in tension: where a layout would put a strut in tension the module says so (“would be in tension in this layout — it is slack and carries nothing”).

The tension crack and the first strut

A clay face stands unsupported down to the depth where its tension crack closes: zc = 2cu/γ for φ = 0, or (2cu − q)/γ with a surcharge. With several layers or a water table the module finds the depth piece by piece, with the total overburden and the surcharge reaching 2cu. The first strut should go in above this depth, so that the sheeting never relies on an open clay face deeper than the clay itself can hold.

In the example zc = 2 × 35 / 18 = 3.89 m and the first strut is at 1.00 m: the check is passed, and the working shows “first strut A at z = 1.00 m ≤ zc”. The caution appears when the first strut is deeper. With the struts at 4, 5 and 6 m the module warns:

  • “First strut (A) at z = 4.00 m is deeper than the tensile-crack depth zc = 3.89 m. Below 2c/γ the unsupported clay face is past what it can hold in tension before the strut is installed. Raise the first strut above zc, or justify the temporary unsupported height separately.” The same run also gives, as it must, a heavy first strut: Pmax = 411.1 kN and a sheeting moment of 189.4 kN·m/m, which the sheeting given does not carry (utilisation 1.549).

A surcharge shortens the crack: with 60 kPa the depth is (70 − 60) / 18 = 0.556 m, and a first strut at 1 m triggers the same caution with zc = 0.5556 m. With 20 kPa it is (70 − 20) / 18 = 2.78 m, so the first strut at 1 m passes.

Step 9 of the Calculations tab: the crack depth zc = 2c/γ, zc = (2 × 35.00) / 18.00 = 3.89 m, and first strut A at z = 1.00 m not deeper than zc.
The check of the first strut in the Calculations tab.

Bottom heave of the base

A deep cut in clay can fail by the base bulging up: the clay beneath the excavation is squeezed in under the weight of the soil beside it. The module compares the resistance of the clay along the failure surface with the driving overburden and surcharge:

FSheave = [ 5.14 cu (1 + 0.2 B″/L) + cside H/B′ ] / ( Σγi Hi + q )

B′ is B/√2, or the depth T of the hard stratum when that is smaller; B″ = √2 B′. cu under the base gives the bearing term and cside (the cohesion averaged over the height of the cut) the side shear. Without L the cut is taken as long (the shape term is 1), and without a hard stratum B′ = B/√2. The embedment d of the sheeting is not credited, which is on the safe side. The check is made when Check the base is Yes; the card reads PASS at or above FSreq and FAIL below it.

For the example: B/√2 = 4.24 m ≥ T = 4 m, so B′ = 4.00 m and B″ = 5.66 m; 1 + 0.2 × 5.66 / 20 = 1.0566; FSheave = [5.14 × 35 × 1.0566 + 35 × 7 / 4.00] / 126 = 251.33 / 126 = 1.99, above the required 1.5: PASS. The module gives 1.995.

Step 10 of the Calculations tab: the heave relation, B/√2 = 4.24 m ≥ T, B′ = 4.00 m, B″ = 5.66 m, the shape term 1.0566, FS = 251.33 / 126.00 = 1.99, and the drawing of the base heave with the strip B′, the side shear and the bearing term.
The heave step of the Calculations tab.

What changes the factor of safety

  • Weaker clay: cu = 20 kPa gives 1.140 (hand: [5.14 × 20 × 1.0566 + 20 × 7 / 4] / 126 = 1.14), FAIL against 1.5, with the warning “Factor of safety against bottom heave FS = 1.14 is below the required 1.50. The clay beneath the base cannot carry the overburden beside the cut with the intended margin. Extend the sheeting below the base, reduce the surcharge beside the cut, narrow the cut or improve the clay under the base.” Stronger clay raises it: 50 kPa gives 2.850 and 80 kPa 4.559.
  • Width: B = 4 m makes B′ = 2.83 m and gives 2.172; a width of 10 m leaves B′ = T and the factor at 1.995.
  • Hard stratum and length: with no hard stratum the factor is 1.972; L = 10 m gives 2.075 and an empty L 1.914.
  • Surcharge: 20 kPa gives 1.721 (hand: 251.33 / (126 + 20) = 1.72).
  • A hard stratum at the base (T = 0): no heave surface can develop, no factor is given, and the module notes “Hard stratum at the base of the cut — bottom heave cannot develop.”

Analyze and read the results

Press Analyze. The bar changes to Analysed — the braced cut calculated, with — n warnings added when there are warnings. The module stays on the Model tab (the bar, with Warnings or Notes, Edit inputs and Analyze, belongs to that tab): open the Results tab. The window of the warnings does not open by itself.

The Results tab shows, from the top:

  • Half section — dimensions and struts and Pressure on the sheeting: half the cut to its centre line, with the strut sections, beside the envelope with σa and the envelope resultant and the total on the wall.
  • Strut loads and Wales — seen from inside the cut: the load of each strut, and the moment and shear of each wale between the struts.
  • Values, step by step, then the table of the beam pieces of the wall, the strut loads and the wales, level by level.
  • The cards, last, under Braced cut.
The first block of the Results tab: the half section with the strut sections and the pressure on the sheeting, sigma a = 37.80 kPa, then the strut loads 162.06, 271.26 and 162.06 kN and the wales with their moments and shears.
The drawings of the Results tab.
The Values, step by step table: the envelope with γH/c = 3.60 and σa = 37.80 kPa, Pmax = 271.26 kN, Mmax = 27.03 kN·m/m, Mwale = 101.72 kN·m, zc = 3.89 m, FSheave = 1.99, the design actions and the section checks.
Values, step by step, for the example.
The table of the strut loads: A at 1.000 m with R = 54.02 kN/m and P = 162.1 kN, B at 3.500 m with 90.42 kN/m and 271.3 kN, C at 6.000 m with 54.02 kN/m and 162.1 kN, and the area each needs.
The strut loads.
CardWhat it isThe example
Apparent pressure of the envelope σaThe plateau of the envelope chosen from γH/cu.37.80 kPa
Largest strut load PmaxThe heaviest strut, R × s.271.3 kN
Maximum moment in the sheeting MmaxPer metre of wall.27.03 kN·m/m
Section modulus the sheeting needs Wreq,spThe number a sheet-pile table is looked up with (the design code is named on the card).132.7 cm³/m
Utilisation of the sheeting ηspDesign moment over the resistance of the modulus given; PASS up to 1, FAIL above.0.2212 PASS
Utilisation of the wale ηwaleThe same for the governing wale.0.4994 PASS
Utilisation of the strut ηstrutDesign load over the buckling resistance (with A and I given).0.3500 PASS
Factor of safety against bottom heave FSheaveOnly when the heave check is on; PASS at or above FSreq .1.995 PASS

Beneath the cards stand Maximum moment in the governing wale (101.7 kN·m) and Section modulus the wale needs (499.4 cm³).

The Braced cut cards of the example: 37.80 kPa, 271.3 kN, 27.03 kN·m/m, 132.7 cm³/m, 0.2212 PASS, 0.4994 PASS, 0.3500 PASS and 1.995 PASS, with the wale moment 101.7 kN·m and the wale modulus 499.4 cm³.
The cards of the example.

The members and the design code

With EN 1993-1-1 the working loads are multiplied once by γF: NEd = 1.35 × 271.26 = 366.20 kN, MEd = 1.35 × 27.03 = 36.49 kN·m/m for the sheeting, 1.35 × 101.72 = 137.33 kN·m for the wale. Then Wreq = MEd γM0 / fy: 36.49 / 275 000 = 132.7 cm³/m for the sheeting and 137.33 / 275 000 = 499.4 cm³ for the wale. The sections given are held to Mc,Rd = W fy / γM0 : 165.00 kN·m/m for 600 cm³/m (utilisation 36.49 / 165.00 = 0.2212) and 275.00 kN·m for 1 000 cm³ (137.33 / 275.00 = 0.4994). The strut, with A = 65.7 cm² and Imin = 3 598 cm⁴ over 6 m, has Ncr = 2 071 kN, λ̄ = 0.9339, χ = 0.5791 and Nb,Rd = 1 046 kN, so ηstrut = 366.20 / 1 046.36 = 0.3500: buckling governs over the cross-section check (0.2027).

With AISC 360-22 the same cut needs Wreq,sp = 174.7 cm³/m by LRFD (the moment factored by γH = 1.6) and 164.1 cm³/m by ASD, with the sheeting utilisation 0.2912 and 0.2736. The partial factor matters as well: γF = 1.5 gives 147.4 cm³/m. Steel S355 for the three members (with fy = 355 000 kPa) lowers Wreq,sp to 102.8 cm³/m and ηsp to 0.1713; the strut and wale utilisations fall to 0.3107 and 0.3868. The pressure, the strut loads and the heave factor do not depend on the steel.

Catalogue sections

With From the catalogue for the wale (HEB 300) and the strut (HEB 220) the module checks the class of the section, the shear and the flexural buckling of the strut with the section properties of the catalogue; for the example the wale utilisation is 0.6038 and the strut 0.3511. A section given only by a modulus (or by A and I) cannot be classed; the module then notes that the class was not computed and what the check rests on.

Using the numbers

  • Strut loads are per strut (kN, tf or kip); the sheeting moment is per metre of wall (kN·m/m, tf·m/m, kip·ft/ft) and the wale moment per wale (kN·m).
  • Values are rounded where they are drawn. After a unit switch the drawings keep their labels in m, kN and kPa; the cards, the tables and the report are re-stated.
  • In SI · tf the default example gives σa = 3.860 t/m², Pmax = 27.66 tf and Mmax = 2.760 tf·m/m; in US σa = 0.7895 ksf, Pmax = 61.02 kip, Mmax = 6.077 kip·ft/ft and Wreq,sp = 2.468 in³/ft (37.80 kPa is 0.7895 ksf; 271.26 kN is about 61 kip). The last digit or two can differ, because the unit weight and cohesion are rounded to the digits printed in the chosen unit before the envelope is built: the heave factor is 1.996 in US, 1.998 in SI · tf and 1.995 in SI · kN.

The Calculations tab, the report and the Theory tab

The Calculations tab opens with Given and what is sought and then writes out seventeen numbered steps with your numbers, ending with the notes and the answer:

The Given and what is sought block of the Calculations tab: the clay, the cut H = 7.00 m, B = 6.00 m, L = 20.00 m, the hard stratum, the three struts at 1.00, 3.50 and 6.00 m, the sections of the three members and what is sought.
The first block of the Calculations tab.
  1. Select the apparent-pressure envelope; Idealise the sheeting and solve the strut reactions, with the beam pieces and, for each piece, its own step with the reactions and the shear and moment diagram.
  2. Take the yield strength of each member from its steel grade.
  3. Convert the reactions to strut loads and a preliminary strut area.
  4. The moment in the sheeting; The moment in the wales.
  5. Check the first strut against the tensile-crack depth; Check the base against bottom heave.
  6. Take the design actions from the envelope (γF once).
  7. For each of the sheeting, the wale and the strut, the modulus or the area the code asks for, then the section given verified.

The tab ends with Notes and assumptions and the Answer: “Stiff clay trapezoid, Peck envelope with σa = 37.80 kPa; the heaviest strut is B at P = 271.26 kN …; FS against bottom heave = 1.99 (meets the required 1.50).”

The report

In the Report tab fill in the cover (project, location, client, report number, date, prepared by, title or qualification, checked by, and optional notes). The details are kept in this browser and saved with the model file. Save as PDF and Download Word (.docx) produce the report; the preview below the buttons is the report itself.

The report has seven parts: 1 Introduction and scope, 2 Input data, 3 Calculation (3.1 to 3.17, one for each step), 4 Results, 5 Assumptions and notes, 6 Summary and 7 References.

The Report tab: the cover form, the Save as PDF and Download Word buttons and the first page of the report.
The Report tab.

The Theory tab

The Theory tab has seventeen sections: The braced cut and its members; Why the pressure is not Rankine’s; Apparent pressure from measured strut loads; The envelopes for clay; A surcharge, and water in clay; The first strut and the tension crack; Struts: from the envelope to the strut load; Sheet piles; Wales; The members as they are given; Verifying the steel to EN 1993-1-1; Verifying the steel to AISC 360-22; The envelopes against real cuts; The base of a cut in clay: bottom heave; What the method assumes, and what it leaves out; Worked example; and References. Each opens when you click its title.

Worked example: the module’s own example

The module opens on this example, so you can follow the numbers on your own screen.

Inputs of the example
SectionInputValue
Soil layersClayγ = 18 kN/m³ (saturated 19); cu = 35 kPa
GroundwaterWater tableBelow the base
Cut geometryH, B, L, d, T7 m, 6 m, 20 m, 1.5 m, 4 m
Strutss; levels3 m; 1.0, 3.5 and 6.0 m
SectionsSheeting; wale; strutS275, 600 cm³/m; S275, 1 000 cm³; S275, 65.7 cm², 3 598 cm⁴
Base heave, settingsFSreq; k; code1.5; 0.3; EN 1993-1-1 with 1.35, 1, 1

Step 1: the envelope

γH/cu = 18 × 7 / 35 = 3.60 ≤ 4: the stiff envelope. σa = 0.3 × 18 × 7 = 37.80 kPa, resultant 0.75 × 37.80 × 7 = 198.45 kN/m. The module notes that the ratio is close to 4, where the other branch would give 231.53 kN/m.

Step 2: the reactions and the strut loads

Two pieces, 99.23 kN/m each. RA = 54.02 kN/m, RB = 2 × 45.21 = 90.42 kN/m, RC = 54.02 kN/m. With s = 3 m: PA = PC = 162.1 kN, PB = 271.3 kN.

Step 3: the moments and the sections

Mmax = 27.03 kN·m/m in the sheeting; Mwale = 90.42 × 9 / 8 = 101.72 kN·m. With γF = 1.35: Wreq,sp = 132.7 cm³/m (utilisation 0.2212), Wreq,wale = 499.4 cm³ (0.4994), strut 0.3500. All three PASS.

Step 4: the crack and the base

zc = 2 × 35 / 18 = 3.89 m, the first strut is at 1.00 m. FSheave = 251.33 / 126 = 1.99, above 1.5. Every figure above is one the module gives (37.80 kPa, 271.3 kN, 27.03 kN·m/m, 132.7 cm³/m, 0.2212, 0.4994, 0.3500, 1.995).

The same cut in other units

In SI · tf the example gives Pmax = 27.66 tf (271.26 / 9.807) and Mmax = 2.760 tf·m/m; in US Pmax = 61.02 kip and Mmax = 6.077 kip·ft/ft. The utilisations agree to within about 0.1 % in all three (sheeting 0.2212, 0.2215 and 0.2212).

How each input changes the answer

Each row changes one thing in the example (clay with γ = 18 kN/m³ (saturated 19) and cu = 35 kPa, H = 7 m, B = 6 m, L = 20 m, d = 1.5 m, T = 4 m, struts at 1, 3.5 and 6 m, s = 3 m, no water, no surcharge, k = 0.3, Auto hinges, S275, EN 1993-1-1) and runs the module again. The numbers are the ones the module gives.

Changeσa kPa
Pmax kN
Mmax kN·m/m
FSheave
The example (reference)37.80
271.3
27.03
1.995
cu = 20 kPa (ratio 6.3, soft to medium)46.00
338.1
32.89
1.140
cu = 28 kPa (ratio 4.5, soft to medium)37.80
277.8
27.03
1.596
cu = 31.5 kPa (ratio 4.0, stiff)37.80
271.3
27.03
1.795
cu = 50 kPa37.80
271.3
27.03
2.850
γ = 20 kN/m³ (saturated 21; ratio 4.0)42.00
301.4
30.03
1.795
H = 9 m (struts as before)48.60
882.1
218.7
1.659
H = 5.5 m, struts at 1, 2.5, 4 m29.70
163.5
12.14
2.406
k = 0.450.40
361.6
36.04
1.995
Uniform surcharge 20 kPa37.80
397.2
37.92
1.721
Water table at 2 m39.29
281.9
28.10
1.919
s = 4 m37.80
361.7
27.03
1.995
s = 2 m37.80
180.8
27.03
1.995
Four struts at 1, 2.5, 4, 5.5 m37.80
180.3
12.15
1.995
Hinges at every strut37.80
279.9
28.78
1.995
Struts at 4, 5, 6 m37.80
411.1
189.4
1.995
d = 3 m37.80
271.3
27.03
1.995
B = 4 m37.80
271.3
27.03
2.172
Wale W = 300 cm³37.80
271.3
27.03
1.995
Strut A = 20 cm², Imin = 500 cm⁴37.80
271.3
27.03
1.995
  • cu and γ act through the stability number. Between 31.5 and 80 kPa the envelope does not change (k γH stays 37.80 kPa); only the heave factor rises, from 1.795 to 4.559. Below the changeover the envelope grows as the clay weakens: 338.1 kN at 20 kPa.
  • H moves everything: from 5.5 to 9 m the largest strut load goes from 163.5 to 882.1 kN and Mmax from 12.14 to 218.7 kN·m/m, so at 9 m the sheeting, the wale and the strut given are all FAIL (utilisations 1.789, 1.624 and 1.138).
  • The embedment d changes nothing in the strut loads or the heave factor: it is not credited.
  • The struts given (the last two rows) change only their own utilisation: a wale of 300 cm³ gives 1.665 (FAIL), and a strut of 20 cm² 1.871 (FAIL).

Messages: when the module stops, and what it says

The module checks the numbers it needs before it calculates. When one cannot be used it stops and nothing is calculated; otherwise it calculates and lists warnings and notes.

  • A value outside its range stops the analysis with a window titled Cannot analyse — 1 input error (or 2 input errors …) that lists each message. The limits are shown in the units of the unit system chosen.
  • A condition of the solution that is not met stops it in a window titled Cannot analyse — a condition of the solution is not met, which ends “Nothing was calculated. Change the inputs marked in red, then press Analyze again.”
  • Warnings (△) and notes (○ and ●) are listed on the Warnings (n) or Notes (n) button of the bar; the button reads Warnings when there is at least one warning. The bar reads Analysed — the braced cut calculated — 1 warning in that case.
The window Cannot analyse, 1 input error: Depth of the cut (H) must be at least 0.5 m.
The window Analyze opens when the depth of the cut is 0.2 m.
The window Cannot analyse, a condition of the solution is not met: Strut C at z = 8.00 m lies outside the cut.
The window for a strut below the base.

Stops: a value out of range

WhenThe messageWhat to do
H below 0.5 m, or empty“Depth of the cut (H) must be at least 0.5 m.” / “Depth of the cut (H) is missing.”Enter the depth.
cu below 1 kPa“Undrained cohesion (cu,1) must be at least 1 kPa.”Enter cu.
A unit weight below 1“Unit weight (γ1) must be at least 1 kN/m³.”Enter the unit weight.
s below 0.5 m“Horizontal strut spacing (s) must be at least 0.5 m.”Enter the spacing.
fy below 100 000 kPa“Yield strength (fy) must be at least 100000 kPa.”Choose a grade or type fy.
k above 0.4“Stiff-clay envelope coefficient (k) must be at most 0.4.”Enter k from 0.2 to 0.4.
FSreq above 3“Required factor of safety against heave (FSreq) must be at most 3.”Enter 1 to 3.
A modulus below 1 cm³/m“Section modulus of the sheeting (W) must be at least 1 cm³/m.”Enter W.
A thickness below 0.1 m“Thickness (Hi,1) must be at least 0.1 m.”Enter a thickness.
A strut area below 0.1 cm²“Cross-section area (A) must be at least 0.1 cm².”Enter A.

The layer number is part of the symbol: Hi,1, cu,1 and γ1 belong to layer 1.

Stops: a condition of the solution

WhenThe messageWhat to do
A strut at or beyond the base (or the surface)“Strut C at z = 8.00 m lies outside the cut. Every strut must sit strictly between the ground surface (z = 0) and the base (z = H = 7.00 m). Move it inside the cut or remove it.”Move it inside the cut or remove it. A shallower cut with the same struts gives the same message.
Two struts at the same depth“Two struts share the depth z = 1.00 m. Coincident struts leave a zero span between supports and the beam statics break down. Merge them into one level or separate them.”Merge them or separate them.
Fewer than two struts“At least two struts are required” (a single level is a propped wall, which the method does not cover); the Struts section counts from 2, so this can arise only from a model opened from a fileAdd a second strut.

Warnings

A warning does not stop the analysis; the results are calculated.

WhenThe warningWhat to do
The heave factor is below the required“Factor of safety against bottom heave FS = 1.14 is below the required 1.50. …” (with cu = 20 kPa; the card reads FAIL)Deepen the sheeting, reduce the surcharge, narrow the cut or improve the clay.
The first strut is deeper than the crack“First strut (A) at z = 4.00 m is deeper than the tensile-crack depth zc = 3.89 m. …”Raise the first strut above zc.
A member does not carry its load“The wale given does not carry the design moment: MEd / Mc,Rd = 1.66. Mc,Rd = 82.50 kN·m against a design moment of 137.33 kN·m. The wale asks for 499.37 cm³. …” (wale of 300 cm³); likewise for the sheeting (“… the design moment: MEd / Mc,Rd = 1.79 …”) and “The strut section given does not carry the design load: NEd / Nb,Rd = 1.87. Over an effective length of 6.00 m the buckling resistance of this section is 195.73 kN, and the design load is 366.20 kN. …”A heavier section, a higher grade, a closer spacing for the wale, a shorter buckling length for the strut.
One strut carries much more than the average“Strut C carries 882.09 kN, 2.3 × the average of the 3 struts (the lightest, B, carries 89.31 kN). …” (with H = 9 m)Even the layout out: similar tributary heights, the lowest strut nearer the base, or one more level.
The cut is shallower than about 6 m“Cut depth H = 5.50 m is shallower than the ≈6 m the envelopes were derived for. …” (a note)Use the result as a preliminary estimate and confirm it by another method or by monitoring.

Notes

The Notes (5) of the example, and their conditions:

  • The stability number close to 4, with the resultants of the two branches (only when γH/cu lies between 3.6 and 4.4).
  • The sheeting is checked on the modulus given, as the modulus of the whole wall: a wall of U-sections may have its modulus reduced where the interlocks can slip, a wall of Z-sections carries the full value.
  • The wale was verified on the modulus given; its shear resistance was not checked (a catalogue section is checked for shear too).
  • The class of the strut section was not computed for a strut given by A and I; the resistance is on the gross area, correct for a class 1, 2 or 3 section.
  • With a water table: Computed undrained (no separate hydrostatic pressure on the clay envelope); with a surcharge: Computed with the surcharge q = … added as a uniform lateral pressure; with no hard stratum: Computed with no hard stratum below the base; with several layers: Bottom heave computed layer by layer; and always Computed with the bracing loads factored by γF = 1.35 before the code check (the envelope is an upper bound of measured loads, so the factor turns it into the design action).

Good practice and common mistakes

  • Check cu against the tests when the ratio is near 4. A few per cent on cu can change the branch and a sixth of the load; run the other branch and design for the heavier.
  • Choose k on purpose for a stiff clay: the loads follow it in proportion.
  • Keep the first strut above zc. Where the clay will stand open deeper, justify the temporary unsupported height separately.
  • Do not rely on the sheeting embedment for the heave check. The module does not credit d; keep the heave check on and give the width and, if there is one, the hard stratum.
  • Look at the loads of all the struts. An uneven layout puts the lowest strut under the overhang below it; the module says so, and a level more or another hinge convention evens it out.
  • Give the members. Without a section the member is not verified; with a modulus (or A and I) the class and the shear are not computed, with a catalogue section they are.
  • The envelope is for a cut of 6 m or more. For shallower cuts treat the result as a preliminary estimate.
  • Add the surcharge as a load, not by raising γ; it reaches the struts as its own lateral pressure.
  • Check the long term separately. The clay envelopes are total-stress; if the sheeting stays long enough for the clay to drain, the drained loading is a separate case.
  • Save before you leave. The page opens on the default model; use Save to file… or Quick Save….

Frequently asked questions

How does the module choose between the two clay envelopes?

By the stability number γH/cu. Above 4 it takes the soft-to-medium envelope with σa = max(γH − 4cu, 0.3γH); at 4 or below the stiff one with σa = kγH. The example (18 × 7 / 35 = 3.60) is stiff with 37.80 kPa; with cu = 20 kPa it is soft to medium with 46.00 kPa.

What happens when the ratio is close to 4?

The plateau σa is the same on both sides, but the soft-to-medium envelope has a resultant a sixth larger. Between 3.6 and 4.4 the module adds a note with the resultants of both branches and advises running the other branch and designing for the heavier.

How are the strut loads found?

The sheeting is hinged at the struts (the convention is yours; Auto takes the interior struts and switches if a strut would be in tension), each piece between hinges is a determinate beam, the reaction per metre is multiplied by the spacing. The example gives 162.1, 271.3 and 162.1 kN.

What is the tension-crack check?

The first strut should be above zc = 2cu/γ (less a surcharge). In the example zc is 3.89 m and the first strut is at 1 m; at 4 m the module warns.

What does the bottom heave check use, and is the embedment credited?

The bearing resistance of the clay under the base, 5.14cu(1 + 0.2B″/L), plus the side shear of the cut height, against the weight of the soil beside the cut and the surcharge. B′ is B/√2 or the depth of a hard stratum if smaller. The sheeting embedment is not credited. The example gives 1.99.

How is a surcharge treated?

As its own uniform lateral pressure equal to q over the full height, beside the envelope and not inside it. It also enters the heave check and shortens the tension crack. 20 kPa takes the largest strut load from 271.3 to 397.2 kN.

Can I have more than one clay layer?

Yes, up to ten. The layers inside the cut are thickness-averaged into one cu and one γ; the layer under the base carries the heave check; the bottom layer runs on below the base.

Does the water table change anything?

Only the unit weight: the envelope is total-stress, no separate water pressure is added, and below the table the clay weighs its saturated unit weight. A table at 2 m takes σa from 37.80 to 39.29 kPa.

Which codes does it check the steel to?

EN 1993-1-1 with γF, γM0 and γM1 , or AISC 360-22 by LRFD or ASD. The sheeting and the wale are checked in bending (the wale in shear too from the catalogue), the strut in compression and flexural buckling.

Can I drag the struts?

Yes, before Analyze: a strut moves in steps of 0.05 m and its depth in the Struts section follows. Keep it above the base. Nothing else on the drawing is dragged, and after Analyze the model is locked until you press Edit inputs.

Does the module remember my inputs?

No. The page opens every time on the default model, not analysed; only the unit system is kept. Use Save to file or Quick Save to keep a model, and Open file or Load to bring it back.

What does the report contain?

A cover with your project details, then seven parts: introduction and scope, input data, the calculation step by step (3.1 to 3.17), results, assumptions and notes, summary and references, with the drawings, as a PDF or Word file.