On this page · 21 chapters
- 1The model of the wall
- 2Model at a glance
- 3Coordinates, free body, force ledger and sign convention
- 4Geometry decomposition: parts, centroids and lever arms
- 5The soil moving with the wall: heel block, zones, moist and saturated weight
- 6Effective stress and groundwater
- 7Rankine active and passive earth pressure
- 8Coulomb earth pressure on the vertical plane
- 9At-rest pressure and passive resistance (simplified shear-key method)
- 10Surcharge loads
- 11Hydrostatic water on both sides and uplift
- 12Mononobe–Okabe seismic earth pressure
- 13Hydrodynamic water
- 14Inertia of the wall and of the soil moving with it
- 15Relief shelves
- 16Shear keys — simplified shear-key method
- 17Sliding, overturning and bearing
- 18Structural actions: stem, toe, heel, shelf and key
- 19Worked example: a wall calculated step by step
- 20Variables
- 21References
The wall is treated as a reinforced-concrete cantilever retaining system per unit length. The retained side consists of one soil layer and may include a sloping backfill, uniform surcharge and groundwater. The wall geometry may include an optional pressure-relief shelf and an optional shear key beneath the base slab.
1The model of the wallWhat is analysed, and how it is drawn.
Analysis concept
Rankine · static
Suitable for a conventional active/passive earth-pressure idealization. Wall friction is not explicitly used in the classical Rankine coefficient.
Coulomb · static
Acts on the vertical plane at the heel edge (soil against soil) with δ = β, so no concrete wall friction is used; for this plane (α = 90°, δ = β) the Coulomb Kₐ equals the Rankine Kₐβ exactly. The external thrust always acts on this vertical plane; only the stem structural actions use the stem back-face angle (Section 17).
Mononobe–Okabe · seismic
The seismic earth pressure is always the Mononobe–Okabe pseudo-static thrust: the Coulomb wedge with the inertia forces kₕ·W and ±kᵥ·W added, solved on the same pressure plane as the static case (the vertical plane at the heel edge, δ = β).
Uniform surcharge
A uniform surface surcharge produces an additional lateral pressure. Its distribution depends on the selected earth-pressure formulation and is reported separately from the soil self-weight component.
Theory manual
The overview above summarises the model. The manual below is written as a self-contained manual: every quantity that appears in the Calculations tab is explained from its physical idea, drawn, derived and then tied to the exact way the solver evaluates it. A complete numerical example (Section 18) is computed by the same engine that runs the tool, so every substitution printed there can be checked by hand.
2Model at a glanceGroundwater, relief shelf, shear key, the three stability checks and the symbols of the overview.
Groundwater & effective stress
Below the groundwater table, effective vertical stress should be calculated using submerged soil unit weight while hydrostatic water pressure is applied independently. If retained-side and front-side water levels differ, the wall experiences a net water-pressure component and the project should also consider the appropriate hydraulic stability/seepage condition.
Optional pressure-relief shelf
The shelf is modeled as part of the reinforced-concrete geometry with user-defined elevation, projection and thickness. It changes wall self-weight, soil-overburden geometry and the lateral-load transfer arrangement. The soil above the shelf is carried by the shelf. Below the shelf underside the stem pressure restarts as K·[σ′v(z) − R·σ′v(zL)] with R = min(Ls/bkr, 1); surcharge and water are not reduced. The relieved pressure is used for the stem and the shelf root and, with the same R, for the soil self-weight pressure on the virtual back x = B in the external stability; under the earthquake the full increment of the wall without the shelf is added (PAE,shelf = PA,shelf + ΔPAE,0). The counter-moment of the shelf load is not credited to the stem. The Calculations tab prints the reduction.
Optional shear key
The shear key is modeled below the base with user-defined width, depth and offset. The resistance on its front face (base underside → key tip), p = Kmob·σ′v with Kmob = w·Kp + (1 − w)·K0 (w = 1/3 by default: 1/3 Passive + 2/3 Rest), is added in full to the sliding resistance as Pkey.
Stability checks
Sliding
Resistance is the base friction μb·N plus Ptoe and Pkey; no base adhesion is used.
Overturning
Moments are commonly evaluated about the toe for the governing load combination.
Bearing pressure
The result is checked against no-tension/contact criteria and allowable or design bearing resistance.
RC elements
Stem, toe, heel, shelf and key are separate structural elements. GeoTerva gives their shear forces and bending moments from the same load cases used in the geotechnical stability calculation; reinforcement design is outside the tool.
Variables
3Coordinates, free body, force ledger and sign conventionFree body, force ledger, M = x·Fz − z·Fx.
Stability is an equilibrium problem, so the first step is to decide what is in equilibrium and how forces and moments are signed. Mixing conventions (for example taking some moments "clockwise positive" and others "overturning positive") is the most common source of error in hand calculations; GeoTerva therefore uses one Cartesian system for everything.
Coordinates
The origin O is at the toe edge, on the underside of the base slab. x points toward the backfill and z upward. The base top is at z = tf, the wall top at z = tf + H, the heel edge at x = B = Lt + tb + Lh, and the bottom of a shear key at z = −dk.
Forces and the moment about the toe
A force acting on the free body is written by its components (Fx, Fz) and a point on its line of action (x, z). Its moment about O is the two-dimensional cross product r × F:
Why this sign is "overturning positive". A weight W at x > 0 has Fz = −W, so M = −x·W < 0: it holds the wall back. An earth thrust at height z pushing toward the front has Fx < 0, so M = −z·Fx > 0: it turns the wall over the toe. Uplift (Fz > 0) gives M > 0, front resistance (Fx > 0) gives M < 0. No force category is hard-coded as "resisting": each of the two parts x·Fz and −z·Fx is classified by its own sign. The vertical component of an inclined earth thrust, for example, is correctly counted as resisting.
The free body
The free body is the concrete plus the soil that moves with it (the heel block of Section 4). It is cut out along the base underside and along the external pressure plane. Everything that acts across those cuts, and every body force inside them, is one entry of the force ledger. The three checks read the same ledger, so a force can never be forgotten in one check and counted in another.
| Ledger id | Force | Sliding | Overturning | Bearing |
|---|---|---|---|---|
W_CONCRETE | Concrete self-weight (all parts) | yes | yes | yes |
W_SOIL_HEEL | Soil moving with the wall (γ above, γsat below the GWT) | yes | yes | yes |
Q_HEEL | Surcharge over the heel soil — a favourable load that may be absent, always excluded | no | no | no |
W_SOIL_TOE | Front fill over the toe — rests on the toe slab and moves with the wall | yes | yes | yes |
PA_STATIC, PA_Q | Static active thrust of the soil and of the surcharge | yes | yes | yes |
PA_SP | Lateral pressure of the strip and point loads (rigid-wall elastic solutions), all cases at full value | yes | yes | yes |
PAE_TOTAL | Total seismic active thrust (soil + surcharge) | yes | yes | yes |
U_REAR, U_FRONT | Hydrostatic water on the retained and front sides | yes | yes | yes |
UPLIFT | Water pressure on the base underside | yes | yes | yes |
HD_REAR, HD_FRONT | Hydrodynamic water in the seismic cases (retained and front side) | yes | yes | yes |
IH_W_…, IV_W_… | Horizontal and vertical inertia of the concrete, the heel soil and the front fill over the toe | yes | yes | yes |
PP_FRONT, PP_KEY | Front soil resistance on the toe face and the key | yes | no | no |
How the checks read the ledger
PP_FRONT and PP_KEY onlyA front-side water force has Fx > 0 and therefore reduces ΣHdrive. Section 16 derives the three factors of safety from these sums.
4Geometry decomposition: parts, centroids and lever armsBase, stem rectangle + triangle, shelf, key; centroids and lever arms.
The self-weight of the concrete and its moment about the toe are the backbone of both stability checks. A hand calculation splits the section into simple shapes whose area and centroid are known, computes Wi = γc·Ai for each and adds the moments Wi·x̄i. GeoTerva does exactly the same (the component table of the Calculations tab) and, as an independent check, also computes the whole outline as one polygon; the two must agree to 10⁻⁹.
The parts
| Part | Shape and area A | x̄ from the toe | z̄ from the base underside |
|---|---|---|---|
| Base slab | rectangle, B·tf | B/2 | tf/2 |
| Stem, constant thickness t | rectangle, t·H | Lt + t/2 | tf + H/2 |
| Stem, taper on the front (back face vertical) — rectangle | tt·H | Lt + (tb − tt) + tt/2 | tf + H/2 |
| — triangle | ½·(tb − tt)·H | Lt + 2(tb − tt)/3 | tf + H/3 |
| Stem, taper on the backfill side (front face vertical) — rectangle | tt·H | Lt + tt/2 | tf + H/2 |
| — triangle | ½·(tb − tt)·H | Lt + tt + (tb − tt)/3 | tf + H/3 |
| Relief shelf (vertical back face) | rectangle, Ls·ts | xroot + Ls/2 | tf + hs |
| Shear key | rectangle, bk·dk | xk + bk/2 | −dk/2 |
Shelf levels. The shelf is centred at hs above the base top: its top is at zU = tf + hs + ts/2 and its underside at zL = tf + hs − ts/2. Its root is the stem back face (xU at the top, xL at the underside) and its tip is at xtip = max(xU, xL) + Ls. When the back face is battered the root is inclined and the shelf is a quadrilateral; its area and centroid then come from the polygon formulas.
Weights and moments
In the ledger the concrete is one entry W_CONCRETE with Fz = −Wc at (x̄c, z̄c), so its moment is M = −Wc·x̄c = −ΣMi. The height z̄c is needed only for the horizontal inertia kh·Wc of Section 13.
5The soil moving with the wall: heel block, zones, moist and saturated weightHeel block, pressure plane, moist and saturated zones.
Why does the earth pressure not act simply on the back of the stem? Because the soil standing on the heel cannot slide relative to the heel: when the wall moves, that soil moves with it. In the limiting state the backfill behind it reaches failure along planes that start at the heel, not at the stem. The mechanically consistent free body is therefore the concrete plus this heel block, loaded by the earth pressure on its outer face — the external pressure plane (often called the virtual back).
The plane runs from the ground surface above the heel edge (x = B, z = zground(B)) down to the base underside. On a sloping backfill it therefore includes the rise of the ground over the heel. Above the heel top (z = tf) it is the virtual soil–soil plane; over the base slab thickness (z = 0 … tf) it is the end face of the heel slab, and the same pressure is applied down to the base underside, as in the standard hand calculation (the source, Bowles). Everything between the plane and the stem — soil beside the stem, soil above wall-top level (S_SLOPE), soil on and under a shelf — is weight. A plane from the stem top to the heel bottom is not used: it would cut through the concrete of the heel slab.
The seismic case uses the same plane: the Mononobe–Okabe wedge is solved on the vertical plane at the heel edge with δ = β. By default the plane ends at the base underside: its height is h = zground(B) = tf + H + the rise of the slope over the heel (H is the stem height). For a shear key whose rear face is at the heel edge (within 0.1 mm) the option "Include active earth pressure on rear face of heel shear key" extends the plane down to the key tip (h + dk) for the earth pressure and the surcharge (the retained water stops at the base underside); it is off by default (simplified shear-key method, Section 15).
Zones
For the component table the heel block is clipped into named zones, each split at the retained water table into a moist part (unit weight γ) and a saturated part (γsat):
| Zone id | Region |
|---|---|
S_HEEL | Soil over the heel from the base top to wall-top level (no shelf) |
S_SHELF_TOP | Soil on the shelf: stem back face → shelf tip, shelf top → wall-top level |
S_BESIDE_SHELF | Soil beyond the shelf tip: shelf underside → wall-top level |
S_BELOW_SHELF | Soil below the shelf: base top → shelf underside |
S_SLOPE | The wedge of sloping ground above wall-top level |
Why γsat and not γ′ below the water table? The free body is written in total stress: the soil is weighed with its pore water, and the water pressure on the boundary of the free body (U_REAR on the pressure plane, UPLIFT on the base underside) is applied as separate forces. By Archimedes, total weight minus the resultant of the boundary water pressure equals the effective (buoyant) weight, so the two descriptions are identical — but mixing them (γ′ and uplift) would count buoyancy twice.
Excluded vertical load. The surcharge over the heel block (Q_HEEL) is a favourable vertical load that may be absent when the lateral load acts: it is listed in the ledger as excluded and enters no check, while it still pushes on the plane. The front fill over the toe (W_SOIL_TOE) is different: it rests on the toe slab and moves with the wall, so its weight is a vertical load like the heel soil — in N, in the resisting moment and in the bearing resultant, and on the toe slab as a load — and the front soil still provides the passive resistance of Section 8. Enter hp = 0 when the fill may be removed.
6Effective stress and groundwaterσ′v, pore pressure, γ′ and the porosity of the backfill.
Soil strength and therefore earth pressure are governed by the effective stress — the part of the total stress carried by the grain skeleton. Water has no shear strength: it pushes equally in every direction and is added to the lateral pressure with a coefficient of one. Every lateral pressure in GeoTerva is therefore built in two separate layers: K·σ′v from the soil and u from the water.
Governing equations
ddry is the depth above the water table and dsub the depth below it, both measured from the top of the pressure plane, the ground surface above the heel edge. A uniform surcharge adds q to σ′v at every depth.
Porosity of the backfill
The seismic pore-water assumption (Section 12) needs the dry (skeleton) unit weight, which is not an input. It follows from the phase relations with the specific gravity of the solids, Gs = 2.65 — an internal constant of the module, not an input. With void ratio e, γsat = (Gs + e)·γw/(1 + e); with porosity n = e/(1 + e) this becomes γsat = [Gs(1 − n) + n]·γw, and solving for n:
For γsat = 20 kN/m³, γw = 9.81 kN/m³ and Gs = 2.65: n = (2.65·9.81 − 20)/(1.65·9.81) = (25.9965 − 20)/16.1865 = 0.370 and γd = 20 − 0.370·9.81 = 16.37 kN/m³ — the values the solver prints in its assumption note. Note γd > γ′ = 10.19 kN/m³: buoyancy reduces the weight of the grains, not their mass.
7Rankine active and passive earth pressureActive and passive states, sloping backfill.
Imagine a soil element at depth z behind the wall before anything moves. The vertical effective stress is σ′v and the horizontal one is K0·σ′v (Section 8). If the wall moves away from the soil, the horizontal stress falls while the vertical stress stays the same; the Mohr circle grows to the left until it touches the failure envelope. That limiting horizontal stress is the active pressure. If the wall is pushed into the soil the horizontal stress rises past σ′v until the circle touches the envelope on the right: the passive pressure. The active state needs only a small outward movement (in the order of a few tenths of a percent of the height for granular soil); full passive resistance needs a movement roughly an order of magnitude larger.
Derivation from the Mohr–Coulomb criterion
For a circle touching the envelope τ = σ′·tan φ′ (a line through the origin for a granular soil) the radius equals sin φ′ times the distance of the centre from the origin:
using (1 + sin φ′)/(1 − sin φ′) = tan²(45° + φ′/2). In the active state σ′1 = σ′v and σ′3 = σ′a; in the passive state σ′3 = σ′v and σ′1 = σ′p:
For a dry, uniform backfill of height h the pressure is a triangle, so the thrust and its height above the bottom are Pa = ½·Ka·γ·h² and h/3. Water and a surcharge change σ′v (Sections 5 and 9), not the coefficient.
Sloping backfill
For a ground surface inclined at β, Rankine's argument for a semi-infinite slope shows that the stress on a vertical plane is parallel to the surface. Its magnitude is σ′a = Kaβ·σ′v with
The horizontal component on the plane is Kaβ·cos β·σ′v and the vertical component Kaβ·sin β·σ′v, downward for a rising slope. For β = 0 the expression reduces to Ka. The square root requires β < φ′; for β ≥ φ′ the slope itself is not stable and the calculation is blocked.
Implementation
Built from the real ground surface above the point — γ above and γ′ below the GWT — plus q (Section 5).
σ′a = Kaβ·σ′v, split into its horizontal part Kaβ·cos β·σ′v and its vertical part Kaβ·sin β·σ′v.
Composite Simpson rule along the plane, split at the GWT and the base top, so no panel straddles a kink.
PA_STATIC (soil) and PA_Q (with q minus without q), each with its resultant height z = −Mx/Fx.
Front passive resistance uses the Rankine Kp for a horizontal front ground and a smooth face (no wall friction, which is conservative for passive resistance); see Section 8 for the passive state blend with K0.
8Coulomb earth pressure on the vertical planeTrial wedge, closed form, on the vertical plane with δ = β.
Coulomb (1776) did not look at stresses at all. He took a rigid wedge of soil bounded by the wall back, the ground surface and a trial plane from the wall bottom, and asked what force the wall must supply to keep that wedge in limiting equilibrium. Three forces act on the wedge: its weight W (known), the reaction R of the soil below the trial plane, inclined at φ′ to the plane normal because the wedge is about to slide down, and the wall reaction P, inclined at the wall friction angle δ to the wall normal. The directions of R and P are known, so the force triangle can be closed.
Derivation for a vertical wall and horizontal ground
With a vertical back (α = 90°) and β = 0, the wedge weight is W = ½·γ·H²·cot ρ. Applying the sine rule to the force triangle (the angle between W and R is ρ − φ′, the angle opposite W is 90° + δ − (ρ − φ′)):
The wall must resist the most dangerous wedge, so Pa = max over ρ of P(ρ), from dP/dρ = 0. For δ = 0 this gives ρ = 45° + φ′/2 and Pa = ½·γ·H²·tan²(45° − φ′/2): Coulomb and Rankine coincide.
General closed form
The resultant has a horizontal and a vertical component; the vertical one acts downward on the free body and adds to N and to the restoring moment. GeoTerva distributes the thrust as p = Ka·σ′v along the plane, with σ′v built from the ground surface above the heel edge (γ above and γ′ below the groundwater table).
The plane used by GeoTerva. The Coulomb back is the vertical plane through the heel edge (α = 90°), the same plane as Rankine. That plane is soil against soil, so the real concrete wall friction does not act on it; the thrust is taken parallel to the backfill surface, δ = β. For this plane (α = 90°, δ = β) the Coulomb Ka equals the Rankine Kaβ exactly, for every β, so the two methods give the same pressure on it.
9At-rest pressure and passive resistance (simplified shear-key method)Rankine Kp, Jaky K0, the blend Kmob = w·Kp + (1 − w)·K0, hignore, toe passive.
The at-rest state is the stress state of soil that has not been allowed to strain laterally; for a normally consolidated granular soil K0 = 1 − sin φ′. On the retained side GeoTerva always uses the active state (a cantilever wall is flexible enough to reach it). On the front side K0 is the lower end of the passive state blend below.
Passive pressure
The front soil is described by a blend of the Rankine passive and the Jaky at-rest coefficients with c′ = 0 and the geostatic effective vertical stress (γ′ below the front water level). The front ground lies at Df = hp + tf above the base underside. The top layer hignore may be excavated, softened or disturbed during the life of the wall, so the depth is measured from the lowered ground:
Toe passive resistance (optional, default on)
Full passive resistance needs a displacement far larger than a serviceable wall should have, so the coefficient is interpolated between the at-rest state (no movement, w = 0) and the full Rankine passive state (w = 1); the whole blended resistance is credited. The toe passive can be switched off; the weight of the front fill over the toe is always a vertical load (Section 4).
Used in sliding only
PP_FRONT and PP_KEY enter the sliding resistance only. They are not used in the overturning moment or the bearing resultant.
Seismic cases
No seismic passive coefficient is used. A single factor ηp,E (default 0 = no passive credit) multiplies the same static blended toe and key resistances.
10Surcharge loadsUniform q, its lateral pressure and its vertical load.
A uniform load q spread over the whole backfill surface raises the vertical stress by q at every depth (an infinitely wide load spreads without decay). The lateral pressure therefore gains a constant K·q in the simple case, and the thrust gains K·q·h acting at mid-height of the plane.
How GeoTerva separates it. The thrust is computed twice on the same plane, with q and without q; PA_Q is the difference. This definition stays exact under a sloping ground.
Vertical effect. The surcharge over the heel block (Q_HEEL = q × the horizontal length of ground over the block) is a favourable vertical load and is excluded from every check — an assumption of this module. Its lateral effect is always kept: a load that pushes on the wall when present must be assumed present.
Seismic cases. In the Mononobe–Okabe wedge the surcharge on the wedge top is a force Q with its own inertia kh·Q and (1 ± kv)·Q (Section 11).
Strip and point loads
A strip load q between the distances x1 and x2 from the wall and a point load Q at the distance x press on the wall through the soil, and their effect decays with depth. GeoTerva takes their lateral pressure by the elastic solutions for a rigid wall — the same as the sheet-pile modules and the Surcharge Loads tools: the Boussinesq stress doubled by the wall (the image method). z is the depth below the ground at the top of the wall and x the horizontal distance from the back face of the wall at its top.
Where it acts. The pressure is carried from the ground at the top of the wall down to the bottom of the pressure plane (D = the height of the plane below the wall top), on the stem back face for the structural actions and on the pressure plane for the stability, and it is added to the soil pressure at its full value in the static and in the seismic cases (no combination factor: the loads are taken as present, as the uniform surcharge is). Its resultant is the ledger entry PA_SP: a horizontal force toward the front at the depth where its moment is balanced, closed forms of the integrals above.
Assumptions. A point load nearer than 0.30 m is taken at 0.30 m (the elastic solution is singular at the wall). The pressure of a point load is that on the section of wall through the load — the most loaded metre of wall — and is used for the whole wall, on the safe side. The loads are taken on the ground at the level of the top of the wall, also where the backfill slopes. Only the lateral pressure is taken: the weight of the loads on the soil over the heel is not (a favourable vertical load that may be absent, excluded as the uniform surcharge over the heel is).
11Hydrostatic water on both sides and upliftWater on both sides, linear uplift under the base.
Water pressure is isotropic and acts normal to every surface it touches. The free body of Section 4 is surrounded by water on three of its boundaries: the pressure plane on the retained side, the front face, and the base underside. Each is one ledger entry.
Retained side, U_REAR
zw,rear = tf + H − zw is the elevation of the retained water table (zw = the groundwater depth below the wall top, the input), zbottom the base underside (z = 0) and zPw the height of Pw. With the heel-key active option the plane runs to the key tip for the earth pressure and the surcharge only: the retained water stops at the base underside, and the water on the two key side faces is not added (it cancels to first order). If a falling slope puts the water table above the ground at the plane top, only the part of the column below the plane top loads the plane: Pw = ½·γw·(hw² − h0²), a trapezoid.
Front side, U_FRONT
The front water height hwf is entered above the base top; the water acts on the toe face down to the base underside, so the column is zwf = tf + hwf and Pwf = ½·γw·zwf² at zwf/3. It pushes toward the backfill (Fx > 0) and reduces the net driving force.
Uplift, UPLIFT
The pore pressure under the base is taken to vary linearly from the head at the toe to the head at the heel (straight-line head loss along the base):
Derivation of xU. Split the trapezoid into a rectangle utoe·B at B/2 and a triangle ½·(uheel − utoe)·B at 2B/3 from the toe. Taking moments: U·xU = utoe·B²/2 + (uheel − utoe)·B²/3 = B²(utoe + 2uheel)/6, and dividing by U gives the formula. Uplift acts upward (Fz = +U), so it reduces N — and with it the base friction — and adds an overturning moment U·xU.
U_REAR are applied (Section 4).12Mononobe–Okabe seismic earth pressureθ, the active wedge, the seismic passive credit ηp,E, where the increment acts.
An earthquake shakes the wall and the backfill back and forth. The pseudo-static method replaces this transient loading by constant body forces: every mass m receives a horizontal force kh·m·g and a vertical force ±kv·m·g, where kh and kv are the seismic coefficients (fractions of g). For the wall the critical horizontal direction is the one in which the inertia forces push toward the front — the same direction as the earth pressure. The vertical coefficient is uncertain in sign, so GeoTerva runs both: weights multiplied by (1 − kv) and by (1 + kv).
Gravity and inertia together act like a gravity field rotated by θ from the vertical. Coulomb's wedge is therefore solved for the seismic case by adding the inertia forces to the force polygon — this is the Mononobe–Okabe method, the only seismic earth-pressure theory used by the tool.
11.1 Mononobe–Okabe active thrust
Okabe (1926) and Mononobe and Matsuo (1929) applied Coulomb's wedge with the inertia forces added. Maximising P over ρ gives the closed form (ψ = inclination of the back from the vertical, δ = thrust inclination — δ = β on the vertical plane at the heel edge, β = backfill slope):
For θ = 0 it reduces to Coulomb's Ka. The square root needs φ′ − θ − β ≥ 0: when the rotated gravity is steeper than the friction angle allows, no wedge can be in equilibrium: the thrust keeps growing as the failure plane approaches the backfill surface, the load case is reported with “no solution” and its checks count as not satisfied. GeoTerva solves the same wedge numerically on the case's pressure plane: the forces on the wedge are its weight W, the surcharge Q on its top, the horizontal inertia (W + Q)·kh, the vertical force (W + Q)(1 ± kv), the reaction R at φ′ to the failure plane and the thrust P at δ to the plane normal; the wedge is clipped at the GWT (γ above, γ′ below for the weight, Section 12 for the inertia), so a submerged backfill and a surcharge can be included. For a dry, uniform wedge the closed form is reproduced exactly (tested). The static reference PA of a seismic case is the static-case thrust on the same plane (the Rankine or Coulomb closed form of Sections 6–7, soil + surcharge), so ΔPAE = PAE − PA,static. The wedge with kh = kv = 0 can differ slightly from it (for example with a water table under a sloping backfill); it is shown for information only. For every method the plane is the vertical plane through the heel edge and the thrust is inclined at δ = β (soil against soil, no wall-friction input).
11.2 Passive resistance under the earthquake
No seismic passive coefficient is used. The front soil accelerates with the ground and its resistance is uncertain, so the toe and key passive credit of a seismic case is the static blended resistance (Section 8) multiplied by a single factor ηp,E. The default ηp,E = 0 gives no passive credit; a value above zero is a project acceptance. Base friction uses Neff of each seismic case.
11.3 Where the seismic increment acts — an assumption of this module
The wedge gives the magnitude of PAE but not its distribution. Model tests show that the seismic increment acts higher than the static thrust. GeoTerva takes the increment ΔPAE = PAE − PA (PAE from the wedge, PA the static-case thrust on the same plane, Section 11.1) and assumes for it an inverted trapezoid over the plane height he, 1.6·ΔP/he at the top and 0.4·ΔP/he at the bottom, with u the height above the plane bottom; the static part keeps its static shape:
A non-positive increment keeps the static shape (the static distribution is then scaled to PAE). The stem structural actions use the same assumption: the static stem pressure plus the force difference ΔPE,0 = PAE,stem,0 − PA,stem,0 (trial wedge on the stem back face of the wall without the shelf, δ = β, with and without the inertia; soil + surcharge; horizontal part) distributed as the same inverted trapezoid over the stem height H, resultant at 0.6·H (Section 17).
13Hydrodynamic waterThe parabolic pressure on the water columns; free pore water in the backfill.
When a wall accelerates against free water, the water cannot follow instantly and an additional pressure develops. GeoTerva assumes the classical parabolic pressure for a rigid vertical face and incompressible water and applies it to the vertical projection of the water column on the retained side (HD_REAR) and to the front water (HD_FRONT). It is always included in the seismic cases when water is present — there is no switch; it enters the stability ledger and the stem actions.
Derivation of the resultant and its height
The column runs from the water table to the bottom of the pressure plane. If the water table is above the ground at the plane top (h0 of water above it), only the part below the plane top is applied: P = 7/12·kh·γw·√hw·(hw1.5 − h01.5). On the front face the wall moves away from the water during the critical half-cycle, so the pressure drops; the drop acts toward the front, in the same direction as the rear increase. The stem structural actions use the same water column as the stability case.
Pore water under earthquake: free — an assumption of this module
Below the water table the backfill contains water. The module assumes it is free, able to move relative to the grains: the soil skeleton carries the inertia of the grains only, γd = γsat − n·γw (the porosity n from Section 5), while the weight stays on γ′, and the free water adds the hydrodynamic pressure above. In the wedge the horizontal inertia below the water table is therefore kh·γd·Asub with weight γ′·Asub. Some formulations reduce the hydrodynamic pressure by the porosity; GeoTerva keeps the full γw, which is conservative.
The soil moving with the wall is different. The pore water inside the heel block is enclosed by the stem and the base and must move with the wall, so the horizontal inertia of the heel block uses its total mass (γ above, γsat below the water table). Buoyancy reduces weight, never mass: the horizontal inertia never uses γ′ (active wedge γd, heel block γsat); the vertical force of the wedge is (1 ± kv)·γ′·A.
14Inertia of the wall and of the soil moving with itkh·W and kv·W at the centroids.
The Mononobe–Okabe wedge of Section 11 describes the soil behind the pressure plane. The free body itself — concrete and heel block — has mass too, and in the pseudo-static model it receives the same body forces. They are often the largest seismic load after the thrust, because the heel soil is heavy and its centroid is high.
Wh is the mass-carrying weight: for the concrete Wc; for the heel block and the front fill γ·Amoist + γsat·Asat (Section 12). In the ledger the concrete, the heel soil and the front fill over the toe are one entry each (IH_W_CONCRETE, IH_W_SOIL_HEEL, IH_W_SOIL_TOE, and IV_… when kv > 0). The Calculations tab also lists the inertia of every concrete part and soil zone; their sum equals the ledger entries, which is the hand check.
Why the heights matter. The horizontal inertia enters the overturning moment with the lever arm z̄. The concrete centroid of a tall stem and the centroid of the heel soil lie near mid-height, far above the base, so these moments can exceed that of the seismic thrust increment. The vertical inertia changes both N (sliding) and the restoring moment; the "kv up" case usually governs sliding and overturning, the "kv down" case can govern bearing.
What is not in the free body. Only the surcharge over the heel is an excluded vertical load, so it has no inertia entry; the inertia of the surcharge on the sliding wedge is inside PAE. The front fill over the toe (W_SOIL_TOE) is a vertical load and gets IH_W_SOIL_TOE / IV_W_SOIL_TOE. For the structural actions the inertia of the stem above each section, of the shelf and of the soil on the shelf (total mass, no surcharge) is added (Section 17), and the vertical factor is honoured there as well: the stem, toe, heel and shelf weights, the soil masses resting on them and the surcharge are all taken at (1 ± kv)·W in the load case being analysed, so the two kv directions give different slab moments. The water pressures, the vertical earth-thrust component at x = B and the base contact pressure are not scaled — they already follow from the equilibrium of that load case.
15Relief shelvesLoad carried by the shelf, critical angle and width, full and partial relief, stem moment, earthquake, external stability.
A relief shelf is a reinforced-concrete slab cantilevering from the back of the stem into the backfill. It changes the wall in three ways. (1) It carries the soil above it: that weight goes into the stem through the shelf root. (2) It relieves the stem below it: under the shelf underside the self-weight earth pressure restarts, fully or in part. (3) It adds weight to the wall. Shelves are used for high walls, where the stem moment grows with H³, and for strengthening walls that are found to be deficient.
14.1 The load carried by the shelf
xc is the stem axis at the section considered; ΔM is the counter-moment of the shelf load about that axis (Section 14.4 says what is done with it). In the seismic cases the shelf and its soil also receive kh·(Wsoil,m + Wself), each at its own centroid: Wsoil,m is the total mass of the soil on the shelf (γsat below the GWT, without the surcharge q), and the underside uplift is not deducted. The shelf itself is a cantilever from its root under the same loads (Section 17).
14.2 Critical slip-plane angle and critical width
The shelf is fully effective only when its tip reaches the critical slip plane rising from the bottom of the stem back face. The angle α of that plane from the horizontal follows from the static method in use. For Coulomb it is the closed form of the critical wedge (Zarrabi-Kashani, in Kramer 1996) with θ = 0:
Sign of βw. In GeoTerva βw is the batter of the stem back face from the vertical, + when its top leans toward the backfill (the sign used in bkr, eq. 8). The published closed form takes the batter + when the top leans toward the front (the soil overhangs the face), so (6) is written here with −βw put in for it.
For Rankine, with a backfill inclined at i:
Both give 45° + φ′/2 for i = δ = βw = 0, and (6) with βw = 0 and δ = i reproduces (7). The width that the shelf must span at its underside is the horizontal distance of the plane there, less the horizontal offset of the battered back face:
H is the stem height, z1 the depth of the shelf underside below the wall top and βw the batter of the stem back face (+ when its top leans toward the backfill; see the sign note under (6)). For a vertical back bkr = (H − z1)/tan α.
14.3 Full and partial relief
The relief ratio compares the shelf projection Ls with the critical width:
Below the shelf underside the effective vertical stress that produces the self-weight earth pressure restarts, less the part R of the overburden at the underside:
With R = 1 (Ls ≥ bkr) the diagram splits into two separate triangles. With R < 1 the pressure below the shelf starts from the residual σ0, and every component below the shelf is the linear interpolation between the wall without the shelf (P0) and full relief (P1):
Only the static self-weight pressure of the soil is relieved. The surcharge pressure, the hydrostatic water and the hydrodynamic water are computed with their own relations, independent of the shelf, and added to the relieved soil pressure. Within the shelf thickness the pressure acts on the shelf tip and reaches the stem through the root. "Without the shelf" is the same wall with R = 0, so the reported reduction is due to the shelf only.
14.4 The stem moment: the shelf counter-moment is not credited
The load carried by the shelf (Section 14.1) acts behind the stem axis and its moment opposes the earth-pressure moment. GeoTerva does not credit that counter-moment to the stem: the stem actions are calculated for the relieved pressure alone, which is conservative, and the shelf actions are calculated separately as a cantilever under its own load (Mroot, Section 17). Only a net demand — an underside uplift larger than the load — is applied to the stem.
SHELF_SOIL, SHELF_SELF, SHELF_UPLIFT) appear in the stem-base table, so the omission can be audited.14.5 The shelf under earthquake: no seismic credit
The shelf gives the stem no seismic credit. The static stem pressure is the relieved one; the seismic increment is computed for the same wall without the shelf and added in full with the distribution of Section 11.3.
The relieved profile is never scaled by a seismic ratio: that would let the shelf relieve the earthquake as well. Hydrostatic and hydrodynamic water are added separately and are not relieved. The shelf and its soil receive their own horizontal inertia kh·(Wsoil,m + Wself) on their total mass (γsat below the GWT, no surcharge, no deduction of the underside uplift), each part at its own centroid, and their weights carry the vertical factor (1 ± kv).
14.6 External stability: the same relief on the virtual back
External stability keeps the virtual-back free body of Section 4: the soil between the stem and the pressure plane, with the shelf inside it, moves with the wall, and the shelf and the soil on it stay in the free body as weights. On the vertical virtual back at x = B the soil self-weight pressure is relieved in the same way as on the stem, with the same α, bkr and R (a design assumption of this module: the shelf screens the retained soil below its underside):
The surcharge pressure K·q, the hydrostatic and the hydrodynamic water on the plane are not reduced. Sliding, overturning, eccentricity and bearing use the relieved static soil thrust PA,shelf. In the seismic cases the shelf gets no seismic credit on the plane either: the increment is that of the same plane without the relief, added in full with the inverted-trapezoid distribution of Section 11.3 (resultant at 0.6·he), while PA,shelf keeps its relieved static diagram:
PAE,0 is the Mononobe–Okabe trial wedge on the plane and PA,0 the unreduced static closed-form thrust on the same plane. The Results tab and the reports print Pa,H, FS against sliding and overturning, e and qmax for the same wall without and with the relief.
Reported comparison. The Calculations tab prints α, bkr, R, σ′v(zL) and the residual, the stem pressure and stem-base shear and moment with and without the shelf, with their percentage reductions and the shelf load, and the external-stability quantities without and with the relief.
16Shear keys — simplified shear-key methodSimplified shear-key method: blended key resistance, gross Kp design diagram, pivot, heel-key active pressure.
When friction under the base is not enough, a key cast into undisturbed ground below the base adds the passive resistance of the soil in front of it. GeoTerva uses a deliberately simple method (the GeoTervaStudio simplified shear-key method): the key face receives the blended pressure Kmob·σ′v (Section 8), credited in full in sliding, and the section actions of the key are calculated from the gross full passive diagram.
15.1 Key resistance
15.2 Sliding
The passive resistance is used in sliding only. Under the earthquake both passive terms are multiplied by ηp,E instead (default 0, no passive credit; Section 11.2). ΔFS = Pkey/Hdrive is reported for every case; the key weight is kept in Neff in both.
15.3 Check example
γ = 18 kN/m³, φ′ = 30°, Df = 1.0 m, dk = 0.6 m, hignore = 0, dry soil, 1/3 Passive + 2/3 Rest (w = 1/3):
15.4 Key structure
The key is a cantilever from the base underside; its shear force and bending moment are calculated from the gross full passive diagram (Kp, w = 1 — not the credited blend), split into a rectangle ptop·deff and a triangle ½·(pbottom − ptop)·deff:
Check example (Kp = 3.00: ptop = 54.0, pbottom = 86.4 kPa, Pp,gross = 42.12 kN/m): Prect = 54.0·0.6 = 32.40, Ptri = ½·32.4·0.6 = 9.72 kN/m; Vkey = 42.12 kN/m, Mkey = 32.40·0.30 + 9.72·0.40 = 13.61 kN·m/m.
Key at the toe edge: pivot
Default: overturning about the base-slab front bottom corner. Optional: about the shear-key front bottom corner, where every horizontal force gains the lever arm dk and FSo is lower (Section 16.2).
Key at the heel edge: active pressure
Default: the active pressure acts on the plane from the ground above the heel edge to the base underside, height h = zground(B) (simplified method). Optional: "Include active earth pressure on rear face of heel shear key" extends it to the key tip, h + dk, for the earth pressure and the surcharge; the retained water stops at the base underside.
17Sliding, overturning and bearingDerivations including partial base contact.
16.1 Sliding
At the base underside the wall is held by friction. Summing horizontal forces on the free body, the base must supply the shear T = ΣHdrive − ΣPresist, while the available shear is μb·N (no adhesion is used). Placing all resistance in the numerator gives
μb = tan δb is the base friction coefficient; for concrete cast on the foundation soil δb is commonly taken between 2/3·φ′ and φ′ of that soil. N is an effective normal force because the uplift is part of it. Note that putting the passive resistance in the numerator gives a different number than subtracting it from the driving force; the definition must match the one the required factor of safety was calibrated for.
16.2 Overturning
Pivot. By default the wall overturns about the front bottom corner of the base slab (x = 0, z = 0). For a shear key at the toe edge the option "Shear key overturning pivot" may move the pivot to the shear-key front bottom corner (x = 0, z = −dk): every horizontal force then gains the lever arm dk, the vertical forces keep their arm x. The default is the base-slab corner; the key-corner option gives the lower FSo, because the key passive is never used in overturning. The option has no effect for a key away from the toe edge. The bearing pressure is always evaluated on the base underside.
Each ledger entry contributes its two moment parts −z·Fx and x·Fz; positive parts are added to ΣMoverturning, negative parts (in absolute value) to ΣMresisting. Weights and the vertical component of an inclined thrust resist; horizontal thrusts, uplift, horizontal inertia and upward vertical inertia overturn. The front resistance is not included. Because a force may be counted on either side, FSo is not a unique measure of safety; the eccentricity check of the bearing calculation is the more robust indicator of the same mechanism.
16.3 Bearing pressure
The vertical load V = Σ(−Fz) and the total moment ΣM about the toe locate the resultant on the base. Its lever arm from the toe satisfies V·xR = −ΣM:
Full contact. For a rigid base with a linear contact pressure, q(x) = V/B + (V·e)·(B/2 − x)/I with I = B³/12 per metre, so
The heel pressure stays compressive while |e| ≤ B/6 — the resultant lies in the middle third of the base.
Partial contact. Soil cannot take tension, so beyond the middle third only part of the base is in contact. A triangular pressure of length a has its resultant at a/3 from the toe, which must coincide with xR; its area must equal V:
| Check | Condition | Note |
|---|---|---|
| BEARING | qmax ≤ qall | qall is an allowable pressure supplied by the user |
| ECCENTRICITY | |e| ≤ B/6 | full base contact |
| QMIN | V/B·(1 − 6|e|/B) ≥ 0 | the unclipped linear value; negative means lift-off. The same condition as |e| ≤ B/6, so it is information only, not a separate check |
| Resultant outside the base | xR ≤ 0 or xR ≥ B | the wall overturns; bearing is not evaluated |
18Structural actions: stem, toe, heel, shelf and keyStem, toe, heel, shelf and key shear forces and moments.
Once the wall is stable, each reinforced-concrete element must carry its own internal forces. GeoTerva gives the shear force V and bending moment M at the critical sections for the static and every seismic case, and their envelope; reinforcement design is outside the tool.
Stem
The stem is loaded on its own back face, which is not the external pressure plane: with Coulomb it has its own coefficient at its own wall angle, and the thrust leaves the face at δ = β to its normal (no concrete wall friction input). The horizontal component bends the stem; the component along the face presses down on it. With a sloping backfill the Rankine stress does the same, because it is parallel to the ground surface.
The axial force of a stem section is that vertical component above the section, plus the weight of the stem above it, plus the net load a relief shelf hands over (all scaled by 1 ± kv in a seismic case). It is reported as N beside V and M so a later N–M interaction design can use it; the bending check itself does not use N.
ph is the horizontal pressure on the stem back face: the earth pressure (with a shelf, the relieved pressure of Section 14.3), the hydrostatic water, and in the seismic cases the hydrodynamic water (same column as the stability case) and the increment ΔPE,0 = PAE,stem,0 − PA,stem,0 distributed as in Section 11.3 (trial wedge on the stem back face of the wall without the shelf, horizontal part; resultant at 0.6·H). The stem inertia kh·γc·t(z) above the section and the shelf inertia kh·(Wsoil,m + Wself) of Section 14.5 are added. For a uniform dry Rankine backfill with surcharge and no shelf the base values are
Tension is on the back face of the stem, so the main reinforcement is placed there. The section is checked at the base top; for tall walls the moment falls quickly with height (as H³), which is why stems are tapered or reinforcement is curtailed.
Toe
σc(x) is the contact pressure of Section 16 (compression only), u(x) the uplift (over a key footprint it includes γw·dk). The front fill resting on the toe slab is included as a downward load: wfill = γ·hdry + γsat·hsat (γ above, γsat below the front water level). Wkey,toe = γc·dk·b is the weight of the part of a shear key under the toe (b = the key width between x = 0 and Lt) at its centroid x̄key. In seismic cases γc·tf, wfill and Wkey,toe are multiplied by (1 ± kv). Tension is at the bottom of the toe.
Heel
wsoil = γ·hdry + γsat·hsat is the soil column above the heel; under a shelf it reaches only to the shelf underside, the pore pressure at the underside is added as a separate water load wu = γw·(zw,rear − zL) (zero elsewhere), and the surcharge qs is q beyond the shelf and 0 under it. σc(x) is the contact pressure and u(x) the uplift. Pv is the vertical component of the earth thrust on the virtual back at x = B (static Pa,v, seismic PAE,v of the total thrust; soil + surcharge; downward for a rising slope, zero for a flat backfill): it acts on the heel free body at the heel edge and is the same force as in N. Wkey,heel is the weight of the part of a shear key under the heel. In seismic cases wsoil, qs, γc·tf and Wkey,heel are multiplied by (1 ± kv); the water (wu, u), Pv and the contact pressure are not. The heel usually has tension at the top, because the soil load exceeds the contact pressure near the heel edge.
Shelf and key
The shelf is a cantilever from its root: V = Wsoil + Wself − U and Mroot = Wsoil·(x̄soil − xU) + Wself·(x̄self − xU) − U·(x̄U − xU) (Section 14.1). The key is a cantilever from the base underside loaded by the gross passive diagram: V = Pp,key,gross, M = Prect·(dk − deff/2) + Ptri·(dk − deff/3), which is Prect·dk/2 + Ptri·2dk/3 when deff = dk (Section 15.4).
19Worked example: a wall calculated step by stepA wall calculated step by step with engine numbers.
The example below is solved by the same engine that runs this tool, each time this page is opened. Every line shows the hand formula, the substituted input values and the result printed by the engine; the green tick confirms that the hand formula, evaluated independently in the page, gives the same number. The wall is kept simple — no water, no shelf, no key, a horizontal backfill — so that every step can be followed by hand. The example is in SI units (kN, m, kPa) whatever display units are selected.
| Input | Value | Input | Value |
|---|---|---|---|
| Retained height H | 4.00 m | Moist unit weight γ | 18.00 kN/m³ |
| Stem top / base thickness tt / tb | 0.30 / 0.50 m (back face vertical) | Friction angle φ′ | 30.0° |
| Toe Lt, heel Lh | 1.00, 2.00 m | Uniform surcharge q | 10.00 kPa |
| Base thickness tf | 0.60 m | Base friction μb | 0.55 |
| Front fill hp; w, ηp,E, hignore | 0.80 m; 1/3, 0.00, 0.00 m | Concrete γc | 24.00 kN/m³ |
| Static method | Rankine (vertical plane at the heel) | Seismic | Mononobe–Okabe, kh = 0.15, kv = 0 |
| Required FS (static) | sliding 1.50, overturning 2.00 | Required FS (seismic) | sliding 1.10, overturning 1.10 |
Static case
Base width and heights (origin at the toe, base underside).
Base rectangle, constant-thickness stem rectangle and the tapered triangle on the front side.
| Part | A (m²) | W (kN/m) | x̄ (m) | z̄ (m) | W·x̄ (kN·m/m) |
|---|---|---|---|---|---|
| Base slab | 2.100 | 50.40 | 1.750 | 0.300 | 88.20 |
| Stem — constant-thickness part tₜ (back face vertical) | 1.200 | 28.80 | 1.350 | 2.600 | 38.88 |
| Stem — tapered part on the front side | 0.400 | 9.60 | 1.133 | 1.933 | 10.88 |
| Total | 3.700 | 88.80 | 1.554 | 1.223 | 137.96 |
Flat ground and a vertical back face: the heel block is a rectangle Lh × H, all moist.
φ′ = 30.0°, sin φ′ = 0.5000.
σ′v from the ground at the heel; dry backfill.
Triangle for the soil, rectangle for the surcharge; lever arms above the base underside.
Kmob, c′ = 0, hignore = 0: a triangle from the front ground to the base underside, credited in full.
Every force with its components, point of application and moment about the toe.
| Force | Fx (kN/m) | Fz (kN/m) | x (m) | z (m) | M (kN·m/m) | Used |
|---|---|---|---|---|---|---|
W_CONCRETEConcrete self-weight (stem, base) | 0.00 | −88.80 | 1.554 | 1.223 | −137.96 | SOB |
W_SOIL_HEELSoil moving with the wall (heel side, to the vertical plane at the heel) | 0.00 | −144.00 | 2.500 | 2.600 | −360.00 | SOB |
Q_HEELSurcharge over the heel soil (excluded: variable load) | 0.00 | −20.00 | 2.500 | 4.600 | −50.00 | – |
W_SOIL_TOEFront fill over the toe (rests on the toe slab, moves with the wall) | 0.00 | −14.69 | 0.510 | 1.003 | −7.49 | SOB |
PA_STATICStatic active earth pressure — soil (Rankine) | −63.48 | 0.00 | 3.500 | 1.533 | 97.34 | SOB |
PA_QSurcharge lateral pressure | −15.33 | 0.00 | 3.500 | 2.300 | 35.27 | SOB |
PP_FRONTToe passive resistance Ptoe (Kmob = 1.3333, w = 0.333) | 23.52 | 0.00 | 0.000 | 0.467 | −10.98 | S |
Moments about the base-slab front bottom corner; the passive resistance is not used.
Seismic case
Vertical plane, δ = β = ψ = 0, kv = 0, so cos θ·cos(δ + ψ + θ) = cos²θ.
The static part keeps its shape (soil triangle at h/3, surcharge rectangle at h/2); the increment acts at 0.6·h.
Horizontal inertia at the centroids; no vertical inertia (kv = 0).
No seismic passive coefficient.
| Force | Fx (kN/m) | Fz (kN/m) | x (m) | z (m) | M (kN·m/m) | Used |
|---|---|---|---|---|---|---|
W_CONCRETEConcrete self-weight (stem, base) | 0.00 | −88.80 | 1.554 | 1.223 | −137.96 | SOB |
W_SOIL_HEELSoil moving with the wall (heel side, to the vertical plane at the heel) | 0.00 | −144.00 | 2.500 | 2.600 | −360.00 | SOB |
Q_HEELSurcharge over the heel soil (excluded: variable load) | 0.00 | −20.00 | 2.500 | 4.600 | −50.00 | – |
W_SOIL_TOEFront fill over the toe (rests on the toe slab, moves with the wall) | 0.00 | −14.69 | 0.510 | 1.003 | −7.49 | SOB |
PAE_TOTALTotal seismic active earth pressure incl. surcharge (Mononobe–Okabe) | −102.36 | 0.00 | 3.500 | 1.930 | 197.60 | SOB |
IH_W_CONCRETEHorizontal inertia kₕ·W — concrete | −13.32 | 0.00 | 1.554 | 1.223 | 16.28 | SOB |
IH_W_SOIL_HEELHorizontal inertia kₕ·W — heel soil | −21.60 | 0.00 | 2.500 | 2.600 | 56.16 | SOB |
IH_W_SOIL_TOEHorizontal inertia kₕ·W — front fill over the toe | −2.20 | 0.00 | 0.510 | 1.003 | 2.21 | SOB |
The resultant moves toward the toe and leaves the middle third.
Structural actions at the stem base, toe and heel
Pressure from the wall top; no water.
Static stem pressure + seismic increment (Section 11.3) + stem inertia.
Linear contact pressure from qtoe = 100.22 kPa to q(Lt) = 83.36 kPa; slab weight γc·tf = 14.40 kPa.
Downward γH + q + γctf = 96.40 kPa; upward contact from 74.93 kPa at the stem back face to 41.20 kPa at the heel edge.
| Check | Static | Required | Seismic | Required |
|---|---|---|---|---|
| Sliding FS | 2.026 | 1.50 | 0.976 | 1.10 |
| Overturning FS | 3.812 | 2.00 | 1.857 | 1.10 |
| qmax (kPa) | 100.22 | 200.00 | 175.10 | 200.00 |
| |e| (m) | 0.243 | 0.583 | 0.808 | 0.583 |
20VariablesEvery symbol used in the tool.
21ReferencesThe three theories and the source used.
The three theories of the tool and the source whose presentation of their closed forms (Ka, Kp, KAE) the manual follows. Everything not derived from them is an assumption of this module and is marked so in the text.
- Coulomb C.A. (1776) Essai sur une application des règles de maximis et minimis à quelques problèmes de statique relatifs à l'architecture. Mémoires de l'Académie Royale des Sciences 7, Paris.
- Das B.M. (2016) Principles of Foundation Engineering, 8th ed. Cengage Learning, Boston.
- Mononobe N., Matsuo H. (1929) On the determination of earth pressures during earthquakes. Proceedings of the World Engineering Congress, Tokyo, 9:177–185.
- Okabe S. (1926) General theory of earth pressure. Journal of the Japanese Society of Civil Engineers 12(1).
- Rankine W.J.M. (1857) On the stability of loose earth. Philosophical Transactions of the Royal Society of London 147:9–27.
From theory to your own design
Check your own cantilever wall in minutes
- The factors of safety for sliding and overturning, the bearing pressure and the eccentricity
- Static and seismic cases, with water, a surcharge, a shelf or a shear key
- Shear and moment in the stem and the slabs
- A clean calculation report, saved as a PDF. Online: nothing to install, no dongle, on a phone, a tablet or a PC

PDF